Flexible Manufacturing Welding Safety Copyright © Texas Education Agency, 2012. All rights reserved. 1.

Slides:



Advertisements
Similar presentations
Before starting actual arc welding the student should be fully aware of the dangers involved. The high temperature arc and hot metal can cause severe.
Advertisements

Using Gas Welding Equipment
Ag Metals I Using Gas Welding Equipment. Objectives Identify major part of oxyacteylene welding equipment Change oxygen and acetylene cylinders Turn on.
Manufacturing Processes Lab I MET 1321 Stick Welding
Unit: Oxy-Acetylene; Welding, Brazing, Cutting & Heating
Oxygen/ Fuel Cutting and Welding By Ryan Saucier.
Welding, Soldering, Brazing
Arc Welding Basic Safety.
Oxy Fuel Cutting Systems Basic Setup & Use
SMAW (Stick Welding) SECTION OVERVIEW:
Arc Welding. Objectives Apply your welding knowledge to construct a butt weld in a group activity with 75% accuracy. Demonstrate how to properly weld.
Flexible Manufacturing
Gas Welding (Oxy-acetylene)
Tungsten inert gas welding (tig)
Welding Basics Manufacturing Technology HPEDSB.
Technology Education Dept. Bellwood-Antis High School Mr. Crowell Mr. Mackereth.
HOW TO LIGHT AND TURN OFF THE OXY-ACETYLENE TORCH
OXY-ACETYLENE TORCHES Protect your head and eyes by wearing proper welding goggles or face shields equipped with a minimum shade 5 lens. Protect your.
Oxy-fuel Welding and Cutting By: John Templeton
TIG Welding Introduction
Unit 4: Oxyacetylene Welding and Cutting in Agriculture
SAFETY TALK - SLIDE 1 OF 14 Elkhart Products Corporation 08/00 WELCOME ELKHART PRODUCTS CORPORATION “TOOLBOX SAFETY TALK” Welding, Cutting, & Burning.
1. An ______________________ is an unexpected undesirable event that can be cause by the personal or individual factors affecting the people involved.
Oxygen/ Acetylene Cutting & Safety By Keith Dover.
Andrew Brock. Terms  The burning qualities of gases are used in Ag Mechanics to heat, weld and cut metals  Weld- to join by fusion  Fusion- melting.
Agricultural Mechanics Fundamentals & Applications Chapter 22—Using Gas Welding Equipment.
Terms and Definitions Base Metal: Metal to be welded Fusion Welding: process that joins metals by heating them to a melting point and allowing them to.
Welding, Cutting, & Burning. GENERAL HAZARDS General hazards of welding include: –Impact –Penetration –Harmful dust –Smoke –Fumes –Heat –Light radiation.
Welding, Cutting, And Brazing
School Safety Training
Oxygen/ Acetylene Cutting & Safety By Keith Dover.
Metal Cutting Processes Flexible Manufacturing
1 Welding Module 10. 2Objectives After this module you should be able to – identify the most common welding hazards – take the necessary steps to avoid.
Welding, Cutting and Brazing 29 CFR 1910, Subpart Q
Copyright  Business & Legal Reports, Inc. BLR’s Safety Training Presentations Welding, Cutting and Brazing 29 CFR 1910, Subpart Q.
Introduction to Welding
Flexible Manufacturing
WELDING EQUIPMENT WELDING EQUIPMENT BRAZING GAS FUSION WELDING GAS FUSION WELDING ELECTRIC ARC WELDING ELECTRIC ARC WELDING INDUSTRIAL TECHNOLOGY- METAL.
Safety Precaution Before starting actual arc welding the student should be fully aware of the dangers involved. The high temperature arc and hot metal.
Introduction to Welding
Welding and Cutting. Objectives In this course, we will discuss the following: OSHA’s minimum requirements for: – Gas welding and cutting – Arc welding.
Shielded Metal Arc Welding. Shielded Metal Arc Welding (SMAW) welding: –The oldest of the arc welding processes. –Uses a filler rod coated with flux.
Welding Transportation Mr. O’Rourke. What is Welding? A fabrication process that joins metal. This is done by melting the work pieces and adding a filler.
Assembly / Disassembly Machines Foldable Information.
Gas Welding.
SHOP SPEED DATE Get to know your work place. #1: MSDS A Material Safety Data Sheet (MSDS) is a document that contains information on the potential hazards.
SMAW (Stick Welding). 2 SMAW Unit Topics During this overview, we will discuss the following topics: Safety SMAW Basics Equipment Set-Up Welding Variables.
Fabrication Welding
TIG lesson Lesson ). ARC Welding Arc welding is a processes where metals are melted and joined together using intense heat produced by an electric arc.
Gas cutting equipment. MIG WELDING  MIG welding :  metal inert gas welding: a method of welding in which the filler metal wire supplies the electric.
Shop safety (General) Original Power Point Created by Mike Tesnohlidek Modified by Georgia Agricultural Education Curriculum Office June 2002.
OXY-FUEL GAS WELDING. TERMS AND DEFINITIONS CONTINUED  Back Fire  Momentary burning back of the flame into the tip.  Flame goes out with a loud snap.
New Mexico FFA Agricultural Mechanics Career Development Event
Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 23 Using Gas Welding Equipment.
Welding/Metal Working Tool Id
Oxy-Fuel Welding. What is Oxy-Fuel Welding? Process the fuses metal together Does not require electricity Uses a torch and filler rod Similar equipment.
Sara $ Issa الكلية التقنية بنزوى Nizwa College of Technology Mechanical Engineering Department welding Done by: Saravanan & Issa AL-Tobi.
GMAW (MIG Welding). 2 GMAW Unit Topics During this overview, we will discuss the following topics: Safety GMAW Basics Equipment Set-Up Welding Variables.
Arc Welding Basic Safety.
The Welding/Cutting Torch Objective 25.0 Demonstrate proper procedures for oxyacetylene processes.
Arc welding produces heat, sparks, and ultraviolet light. The person Welding must protect themselves and OTHERS from exposure. Welding area: Make sure.
Shop safety (General). Safety comes first! l Always wear safety glasses. l When working with heated objects, always wear gloves. l No running or horseplay.
Oxyacetylene Fusion Welding Safety Review
Unit 2: Welding and Cutting with Heat
Using Gas Welding Equipment
Oxyacetylene Welding Equipment
Nizwa College of Technology
Oxygen/ Fuel Cutting and Welding
Stick Welding.
Stick Welding.
Presentation transcript:

Flexible Manufacturing Welding Safety Copyright © Texas Education Agency, All rights reserved. 1

CAUTION Copyright © Texas Education Agency, All rights reserved. 2 There is no all-inclusive list of safety rules that can apply to every lab. Every lab has a different set of needs based on the work environment. In every case, safety first should be the defining element that applies to your individual lab. Machinery should be respected and used with caution. If this warning is not heeded, serious bodily injury could occur, as well as damage to the machine.

Types of Welding Processes Oxyacetylene Welding Arc Welding Tungsten Inert Gas (TIG) Welding Metal Inert Gas (MIG) Welding Spot Welding Plasma Arc Cutting Copyright © Texas Education Agency, All rights reserved. 3

Arc Welding This type of welding joins metal by the heat of an electric arc. The current is passed through a metal rod to the base metal to be welded. The current melts the rod and the base metal in the area to be welded. A coating of molten flux covers the new weld protecting it until cooled. Copyright © Texas Education Agency, All rights reserved. 4

Metal Inert Gas (MIG) Welding MIG welding is a process using a consumable metal wire as an electrode. The weld is shielded from the air by an inert gas, usually carbon dioxide. Copyright © Texas Education Agency, All rights reserved. 5

Oxyacetylene Welding This type of welding uses oxygen and acetylene to produce a flame hot enough to melt metal. The metal fuses together or has filler material added to the puddle of molten metal to help complete the fuse. Copyright © Texas Education Agency, All rights reserved. 6

Spot Welding The spot welder focuses the electric current through two copper electrodes. The sheets to be welded are held under pressure as the current is applied to the electrodes. This current heats the metal and melts it together. Copyright © Texas Education Agency, All rights reserved. 7

Tungsten Inert Gas (TIG) Welding TIG welding uses a tungsten electrode to produce the weld. An inert gas shields the weld from impurities in the air. A filler rod can be used to add metal into the weld area. Copyright © Texas Education Agency, All rights reserved. 8

Plasma Arc Cutting The plasma cutting torch uses oxygen passing through an electric arc. This air is super heated and under pressure. This blows the molten metal from the torch tip as it cuts the metal below. Copyright © Texas Education Agency, All rights reserved. 9

Copyright © Texas Education Agency, All rights reserved. 10 Arc, TIG, MIG Welding

Arc Welder Identification On/Off Switch Ground Clamp Current Selection Switch Welding Electrode Holder Copyright © Texas Education Agency, All rights reserved. 11

Arc, TIG, MIG Welding Safety Rules 1.Weld only in a well vented area. 2.Use welding hoods when arc welding to protect your eyes from arc rays and ultraviolet radiation. 3.Use welding gloves with cuffs to protect your hands as well as wrists and lower arms. 4.Wear fire resistant clothing to protect you from burns and ultraviolet radiation. Copyright © Texas Education Agency, All rights reserved. 12

Arc, TIG, MIG Welding Safety Rules 5.Do not wrap cables or lines around yourself. 6.To pick up hot metal, with a set of tongs or pliers. 7.Turn off all equipment and tank valves when welding is finished. 8.Always clean work area when finished. 9.Place a barrier up around your welding area. Copyright © Texas Education Agency, All rights reserved. 13

Copyright © Texas Education Agency, All rights reserved. 14 Oxyacetylene Welding

Oxyacetylene Welder Identification Oxygen Tank Valve Safety Relief Valve Oxygen Tank Cart Tank Chain Torch Tip Oxygen Regulator Acetylene Tank Knob Gauge Acetylene Regulator Adjustment Acetylene Tank Torch Handle Copyright © Texas Education Agency, All rights reserved. 15

Oxyacetylene Welding Safety Rules 1.The tanks must be in an approved cart or chained to the wall. This will keep them from falling over and exploding. Copyright © Texas Education Agency, All rights reserved. 16

Oxyacetylene Welding Safety Rules 2.Use an approved striker to ignite the torch; never a match. 3.Never get oil, grease or other combustibles around the oxygen tank. This could cause a violent explosion. 4.Open an acetylene tank valve no more then 1 ½ turns so it can be quickly closed if the need arises. Copyright © Texas Education Agency, All rights reserved. 17

Oxyacetylene Welding Safety Rules 5.Acetylene is a very unstable gas. The regulator should be set for 5 to 7 pounds of pressure on the lines. Acetylene can explode at 15 lbs. 6.Use an approved wrench on the tank valve if there is no hand wheel on the tank. 7.When weld is finished, turn off both tanks and bleed the lines. Then loosen the regulator adjustment screw. Copyright © Texas Education Agency, All rights reserved. 18

Oxyacetylene Welding Safety Rules 8.Keep the safety cap on the tanks when not in use. 9.Before installing the regulators, crack the valves on the tanks to clear dust from connections. 10. Always stand to the side when opening the valves on the tanks. Copyright © Texas Education Agency, All rights reserved. 19

Copyright © Texas Education Agency, All rights reserved. 20 Spot Welder

Spot Welder Safety Rules 1.Sparks and flying molten metal can cause a fire. 2.The electric current during spot welding can cause a burn or shock. DO NOT TOUCH THE WELDER ELECTRODES. 3.Wear tinted goggles while spot welding. 4.Wear welding gloves to protect hands from getting burned. Copyright © Texas Education Agency, All rights reserved. 21

Spot Welding Machine Safety Rules 5.Keep fingers from pinch points while welding. 6.Avoid breathing welding fumes. 7.Do not put fingers between the welder tips. Copyright © Texas Education Agency, All rights reserved. 22

Plasma Arc Cutting Copyright © Texas Education Agency, All rights reserved. 23

Plasma Arc Cutting Safety Rules 1.Wear protective clothing when using a plasma cutter. 2.A #5 shaded lens should be worn for plasma cutting. 3.Never use a plasma cutter in an area with combustible or explosive gases or materials. Copyright © Texas Education Agency, All rights reserved. 24

Plasma Arc Cutting Safety Rules 4.Never touch any part of the torch tip or metal being cut. 5.Hearing protection should be worn when operating a plasma cutter. Copyright © Texas Education Agency, All rights reserved. 25