Advanced Engineering Design and Presentation C-Clamp Parametric Modeling Skill Builder Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Creating a C-Clamp Create it to the specifications given. Change colors to match your school’s colors. Change “STEM” to your name or initials. Change “2014” to your graduation year. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Layout Page 1 Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Layout Page 2 Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Layout Page 3 Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. How to Create the Parts Create a folder on your drive for all of the C-Clamp parts and assemblies. Make sure you save to this folder only! The following slides will help you figure out how to create the parts. Part #1 – C-Clamp Base Part #2 – Protection Pad Part #3 – Shaft Screw Part #4 – Screw Swivel Part #5 – Tension Bar Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #1 - C-Clamp Base Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #1 - C-Clamp Base Draw this and extrude it. Copyright © Texas Education Agency, 2014. All rights reserved.

Draw this and then extrude/cut it. Part #1 - C-Clamp Base Draw this and then extrude/cut it. Copyright © Texas Education Agency, 2014. All rights reserved.

Add screw threads to the hole. Part #1 - C-Clamp Base Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #1 - C-Clamp Base Draw this and then extrude/cut it. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #1 - C-Clamp Base Fillet the edges; mirror this using the YZ plane. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #1 - C-Clamp Base Create your initials or name. (Hint: Use the Text tool and then trace over the letters.) Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #1 - C-Clamp Base Repeat on the other side to add your graduation year. (Hint: Use the Text tool and then trace over the letters.) Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #2 - Protection Pad Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #2 - Protection Pad Draw and then extrude this. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #2 - Protection Pad Chamfer the four sides. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #2 - Protection Pad Fillet the one bottom edge. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #3 - Shaft Screw Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #3 - Shaft Screw Draw and extrude this. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #3 - Shaft Screw Draw and extrude. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #3 - Shaft Screw Draw and extrude/cut this. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Add threads. Part #3 - Shaft Screw Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #4 - Screw Swivel Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #4 - Screw Swivel Draw and extrude. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #4 - Screw Swivel Draw and extrude. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #4 - Screw Swivel Add chamfer. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #4 - Screw Swivel Create hole through it. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #5 - Tension Bar Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #5 - Tension Bar Draw and extrude. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Part #5 - Tension Bar Add fillet to both ends. Copyright © Texas Education Agency, 2014. All rights reserved.

Place parts and constrain them to look like this. Assembly Place parts and constrain them to look like this. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Make an Exploded View Make an exploded view by tweaking, moving, and rotating to look like this. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Place the exploded and assembled views onto layout page #1; add the parts list and balloon annotations. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Place the C-Clamp base and protection pad onto layout page #2; add annotations. Copyright © Texas Education Agency, 2014. All rights reserved.

Copyright © Texas Education Agency, 2014. All rights reserved. Place the screw swivel, shaft screw, and tension bar onto layout page #3; add annotations. Copyright © Texas Education Agency, 2014. All rights reserved.

Follow the example and rubric given. Copyright © Texas Education Agency, 2014. All rights reserved.