THINKING SKILLS Year 9 Graphics. What method of drawing am I thinking of? 1. 2 dimensional drawing? 2. Isometric Projection? 3. Orthographic Projection?

Slides:

Advertisements

Similar presentations

Technical Sketching and Drawing

Advertisements

Technical Drawing CHAPTER 1

Isometric Drawing Part 1

Time to Teach Presents Year 7 (National Numeracy Strategy) (Based on DFEE Sample Lessons)

Lecture 3 Sunday, 03 May ENGINEERING GRAPHICS 1E7 Lecture 3: Orthographic Projections.

Engineering Design and Presentation Introduction to Pictorials, Specifically Isometrics Copyright © Texas Education Agency, All rights reserved.

Engineering Design and Presentation

Graphics 2: Isometric Sketching From Different View Points

ENGINEERING GRAPHICS 1E7

Orthographic, Oblique & Isometric Projections

Using Drawings to Communicate. EML 2023 Computer Aided Design communicate design intent How can you sketch this angle bracket to convey its shape effectively?

Orthographic to Isometric

Technical Drawing Visual Communication of Technical Information

Geometry and Measurement: Two- Dimensional. If an angle measures 37.8 degrees, what would be the measure of its supplement?

Dimensioning Dimensioning Gateway To Technology®

Solids and Views A solid is in 3D. But we can only draw in 2D.... So how can we draw a solid?

6.1 Law of Sines Objectives –Use the Law of Sines to solve oblique triangles –Use the Law of Sines to solve, is possible, the triangle or triangles in.

Engineering Graphics III – Pictorial Projections Prof. Jon Southen October 15, 2008.

Fundamental principles of technical sketching and visualization techniques Unit B, Objective 4.01.

Multiview Drawings Warm Ups.

Using Drawings to Communicate Lecture 3 –How to create an isometric drawing of a part when given front, top, & right side views.

CHAPTER 3 REVIEW What are the 7 steps of Engineering Design Process ? 1. Define the problem 2. Research the problem 3. Develop possible solutions 4. Choose.

Space Figures, Nets & Diagrams Objectives:  To identify nets of space figures  To make isometric drawings of space figures.

What’s The Next Step to Beginning a Drawing……. You already Know: Measurements Tools.

Orthographic Projection

Sketching By Brian Nettleton This material is based upon work supported by the National Science Foundation under Grant No Any opinions, findings.

Unit 6 Pictorial Drawings  Recognize pictorial drawings  Sketch isometric & oblique drawings  Identify the difference between cavalier oblique &

A quadrilateral is any 2- dimensional, four- sided shape.

Freehand Sketches.

Isometric Drawings & Orthographic Drawings Tutorial 5d.

Orthographic Drawing. Today I will be learning to : Improve my graphic skills by learning how to draw an Orthographic Projection of a 3D object All: Will.

WHITEBOARD PRACTICE FINDING THE MISSING ANGLE IN AN ANGLE PAIR.

“Key Phrases” What do you want to be in the future? I want to be a _____________. Why do you want to be a ________? I like __________. I am good at ___________.

Tuesday 3:15-4:30. Homework Check pp

Learning Objective: (Over 2 lessons) To be able to construct a 3 dimensional object using the Oblique drawing technique. To be able to create a rendered,

LESSON Today: Go over Part Instruction We are what we repeatedly do. Excellence, then, is not an act, but a habit. Aristotle.

Pictorial Drawing Isometric.

3D Pictorials. Isometric PictorialOblique Pictorial.

Unit 16 Engineering Drawing

Introduction to Pictorials, Specifically Isometrics Copyright © Texas Education Agency, All rights reserved.

Isometric, orthographic, and perspective drawing…

1.2 Drawings, Nets, and Other Models

Year 7 Graphics – Isometric Drawing

Multi-view & pictorial sketching concepts

Task 9 Describe the types of drawings that may be produced by the modelling software.

Nets and Drawings for Visualizing Geometry

Prerequisite Skills VOCABULARY CHECK Copy and complete the statement.

Representations of Three-Dimensional Figures

TECH 104 – Technical Graphics Communication

Technical Drawing.

Introduction to Oblique

‘A children’s day nursery’

Year 7 Graphics – Orthographic Projection

First and Third Angle Projection.

Isometric Projection -the term ‘isometric’ comes from the Greek for ‘equal measure’ reflecting the scale along each axis is the same - Isometric views.

A B C D E F G H Riddles Name: _________________________________

ENGN103 Engineering Drawing

Orthographic Sketch Solution

Technical drawings! Please update your TOC.

Unit 2 Review Introduction to Engineering Design

ENGN103 Engineering Drawing

Visualizing Geometry Skill 01.

S1 Orthographic Sketching

ENGN103 Engineering Drawing

Projections & Technical Drawing

How will I know if I have been successful?

Announcements for Minor-I

State what the angles are indicated by a letter, giving reasons for your answer (1) (2) (3) c 115o 75o b 119o a 50o (4) (5) (6) d 125o 70o f e 110o.

Given that {image} {image} Evaluate the limit: {image} Choose the correct answer from the following:

Presentation transcript:

THINKING SKILLS Year 9 Graphics

What method of drawing am I thinking of? 1. 2 dimensional drawing? 2. Isometric Projection? 3. Orthographic Projection? 4. 3 dimensional sketching? 5. Oblique drawing?

You can see more than one side of an object with this method of drawing.

This method of drawing shows only three sides of an object.

This method of drawing is produced using equipment such as set squares.

This method of drawing uses 30 degrees as the key angle.

Did you get the correct answer? ISOMETRIC PROJECTION

MYSTERY TASK Why did Fred lose his job?

Metacognitive Plenary which key thinking skills have we used today? Information Processing Reasoning Evaluating Enquiry Creativity