Computer Log-in The Lab computers run windows 7 with active directory Login is required Your user id is the same one you use in the rest of the university Your initial password is your user id plus the last 4 digits of your G Number Example: strebelc4321 You are required to change your password the first time you login. Remember to LOGOUT!!!

Ron Grew KEN217 – - Laboratory Supervisor for Kennedy Hall of Eng. Technical Support Lab (KEN234) EE & CE Support Laboratory Equipment Check-out System (KEN234) Lockers in KEN 2 nd & 3 rd floor need to be registered Report damaged equipment or facilities Access Cards

 Pass out Access Cards  Go to address below to Register your cards  DO NOT GO PAST “I ACCEPT” YET! WE WILL GO OVER EACH P&P!  Read and Understand Policy & Procedures for Access Card and Kennedy & Keller Building Use.  If you understand the terms Click “I accept these terms”.  There is a charge that will post to your student account.  If you lose a card or it gets broken it’s a 5.00 charge.  When you return your card, AFTER YOUR LEAVE or GRADUATE the charge will deducted from your student account.

Jerry Smant KEB 105 – - Urban Campus  Security & Public access  Watch / Take care of your stuff  Fire & Weather Safety  Bus Service Engineering Discipline is not Easy! Enhance your “Powers of Observation” Dress for Safety! Rotating Equipment & Dangers of If you have sandals on today this is your one day of Grace! After today you will not be allowed in labs or asked to leave! Signage – Safety Glasses, Shoes, Power, Doors, Etc Privileges - Increase with achievement

Carl Strebel KEN Computer Software – Licensing – Distribution – Installation Computer Hardware – Computers – Printers Contact – 219 KEN – Put something recognizable in the subject

Computer Labs KEB – No General Lab Computer access – No General Use Printers As you progress in your degree, you will get access to the printers in KEB 115, 202, and 211 KEN – KEN244, 250, and 258 – General Computing Labs Your access cards get you into these labs All the software is the same in each lab

Computer Labs The Lab computers run windows 7 with active directory – Login is required Your user id is the same one you use in the rest of the university Your initial password is your user id plus the last 4 digits of your G Number – Example: strebelc4321 You are required to change your password the first time you login. Remember to LOGOUT!!! LOGOUT!!! LOGOUT!!! – You have 1Gb of storage Your desktop, My Documents, downloads, etc will copy between computers

Computer Software Pro-Engineer (Pro-E), Solid Works/Solid Cam, Matlab, Mentor Graphics, etc… Most licensed software can be downloaded and run on your own computer – Downloading and installing is at your own risk! No support is offered All the software you need is already installed in the various labs – Find the software from blackboard->community->School of Engineering -> Computing Resources Available only to Declared Engineering Majors – Direct access to the software Userid: egr Password: student – Warning the downloads are HUGE Make sure you have enough room on you hard drive for the download, uncompressed software and the installed software.

Computer Software Most licensed software can be downloaded and run on your own computer – Follow the directions for installing…do not skip any steps! – If you are using the software from off campus, you MUST use the VPN connection vpn.student.gvsu.edu Login with your university id and password. Click “network connect” in the lower right corner

Printing Printer Setup – For Windows 7 Add printer -> network printer -> Printer isn’t listed -> select a shared printer Enter the generic address of the printer you want – – Example: Most of the printers are HP Select the correct driver for the printer – For other versions of windows the field names maybe different, but it will follow the same basic procedure.

Printing on a Mac

Printing Etiquette Where did my print job go? Don’t print the “Digikey Catalog”! Don’t print to a room where a class is going on! Always pick-up your print job!

Computer Etiquette Do not enter a lab if a class is in session – Go to another lab If a lab is has a sign saying “closed” or a computer is labeled “DO NOT USE”, do not use them! – It takes 1-2 hours to image the computers, and if you use them when they are not ready, they have to be imaged again If the labs are full, please give up your seat if you are not doing school work. Do not steal mice or keyboards, or damage the computers in any way.

Ron Grew Location: 217 John C. Kennedy Hall of Engineering Phone: Department: Engineering, School of Dept. Phone: Jerry Smant Location: 105 Fred M. Keller Engineering Laboratory Building Phone: Department: Engineering, School of Dept. Phone: Carl Strebel PCEC Network Systems Supervisor Location: 219 Kennedy Hall of Engineering Phone: Teamwork! You can’t do it alone! Work with others! Ask for help!