Market introduction CellaTemp PA

 Newest interface technology  Latest high-resolution microprocessors  Newest sensors  New amplifier technology  Improved optical properties  Improved thermal shock behaviour (PA 10) CellaTemp PA – Technical news

 Cylinder-shaped housing with M65 screw thread for very easy mounting  hight-quality stainless steel housing  Bright LED display on the back side (USP)  Connector on the back side  2 current output signal freely configurable in many ways one of these output can be configured as an analog control voltage input (USP)  2 gate inputs/outputs can be freely custom-configured CellaTemp PA – Special features

 Spot Sighting options alternatively:  a) through-the-lens - mirror-inverted  b) integrated laser spot light  c) integrated high dynamic video camera  Integrated USB interface bit/s  RS 485 interface for point-to-point or multidrop network  in the development New configuration software „CellaView“ usable for parallel operation of up to 30 pyroemters  Complete configuration via keypad or PC  Multifunctional configuration possibilities CellaTemp PA – Special features

 Current output 0(4) – 20 mA  Beginning and end of measuring range  Smoothing function  Data storage mode  Emissivity / emissivity ratio setting  Interface selection  Dirty optics detection in the two-colour pyrometer PA 40 CellaTemp PA- Configuration options (1)

 Sensor output curve correction at 10 data points  Sight glass transmittance setting  Compensation for extraneous radiation (PA 10/13)  Automatic emissivity determination (PA 40)  Automatic temperature detection in discontinuous processes  On-site user calibration  Sequence average value - peak value selectable  Laser can be switched on / off CellaTemp PA – Configuration options (2)

 Control voltage input to offset interfering factors such as extraneous radiation.  Extremely wide measuring ranges  High resolution temperature detection 0.2 K % of the adjusted measuring range  Electronic dirty window check PA 40  Test current to perform diagnostics  polarising filter protects the eye against bright target objects (optional accessory) CellaTemp PA – Special features

Configuration of the analogue outputs and inputs

Configuration of the input and output swichtes

PA Connector Pin Assignment

 Both USB and RS485 interface usable at the same time  Employs either RS485 interface for point-to-point communication or USB interface  Integrated software for sensor configuration and data communication. Runs under all common operating systems, executable in any language.  Parameter settings can be adjusted during running operations Features of the interfaces

 Focusable interchangeable lenses  High optical resolution due to multiple-element lenses  Consistently good imaging properties throughout the entire focusing range  Corrected for the infrared and visible spectrum  Large, high-contrast field of view e.g. 42 ° when used with the wide-angle lens  Minimize Size-of-source effect (make CellaTemp PA less sensitive to fluctuating target size or measuring distance) Optical Features

 Distance range is infinitely adjustable and precise thanks to screw thread  Adaptable to supplementary lenses using camera thread  Target size diameter as small as Ø 0.3 mm  Eyepiece also suitable for users who wear glasses due to broadened intrapupillary distance  By using supplementary lenses a myriad numbers of optical solutions are possible Optical Features

 Through-the-lens sighting tube with target marker  Laser spot indicator  Video camera Viewing options

CellaTemp PA with video camera

 Wide measuring ranges  Consistently high resolution throughout the measuring range  Low quantisation noise, even at the lower end of the measuring range Sensor and Signal Processing

Type overview (1) – One colour compact pyrometer

Type overview (2) – Two colour compact pyrometer

Type overview (3) – One colour fibre optic pyrometer

Type overview (4) – Two colour fibre optic pyrometer

Pyrometer CellaTemp PA 83 with rectangular measuring area

CellaTemp PA with fibre optic cable

 Compatible with entire range of CellaTemp PZ accessories  Mounting bracket PA 11/U  Pivoting / tilting pedestal mount PA 11/K  Protective supplementary quartz lens PA 20/I  Protective supplementary ZnS lens PA 10/I  Protective supplementary sapphire lens PA 15/I  Cooling jacket PA 20/B, PA 20/M  Polarizing filter for eyepiece PA 20/P  Connection cable VK 02/A  USB cable VK 11/D CellaTemp PA – Accessories

 Pyrometer  Connecting cable VK 02/A  manual German, Englisch, French depending on order)  USB cable VK 11/D  Software CellaMevis PZ 10/N AF 10_d_e  Type with video camera: video cable VK 02/F incl. adapter to cinch CellaTemp PA – delivery includes

CellaTemp PA – cooling housing PA 20/… open: PA 20/B AF 1 closed: PA 20/M AF 1 For pyrometers with throught-the-lens optic or laser spot marker closed: PA 20/M AF 2 für pyrometer with video camera

CellaTemp PA – protective housing PA 40/… open: PA 40/B AF 1 closed: PA 40/M AF 1 For pyrometers with throught-the-lens optic or laser spot marker closed: PA 40/M AF 2 für pyrometer with video camera

Mounting set PA for cooling and protective housing

Mounting set PA for cooling and protective housing