Geometric & Kinematic Models for An I.C. Engine P M V Subbarao Professor Mechanical Engineering Department Creation of Infrastructure to Facilitate Thermodynamic.

Slides:

Advertisements

Similar presentations

Internal Combustion Engine Induction Tuning

Advertisements

Types of Engines and Uses

Chapter 3 Engine Operation

Engine Geometry BC L TC l VC s a q B

Engine Terminology Engine Measurement Lesson 8 March 2008.

Engine Maintenance Chapter 1 What Makes the Boat Go.

STUDENT NAME: (1) Patel Vidhi A.

Conceptual & Thermodynamic Description of Expansion in I.C. Engine P M V Subbarao Professor Mechanical Engineering Department The Actual & Useful Extent.

Effect of Piston Dwell on Engine Performance P M V Subbarao Professor Mechanical Engineering Department Sufficiency of time to Execute a Process…..

Creation of Ideal Cycles for Internal Combustion Engines P M V Subbarao Professor Mechanical Engineering Department Basic Thermodynamic Structure of an.

Selection of Rod Ratio for I.C. Engines

Variable Compression Ratio By Myles Bohon Robert Dorosko Nana Noel MAE 442 Dr. Klang May 2006.

Four Stroke Cycle Engine

Presented by :- Deepak ranjan swain Regd no: Mechanical.

Lesson 3: Reciprocating Engine Theory Of Operation

Unit A 6-1 Mechanical Systems and Technology. Problem Area 6 Agricultural Power Systems.

Kinematic Analysis for A Conventional I.C. Engine P M V Subbarao Professor Mechanical Engineering Department Creation of Instantaneous Volume, Surface.

Basic Sketch Of Motor How Do We Describe The Physics Of Operation?

Experiment #4 IC Engine.

Internal Combustion Engine Testing

Cylinder Kinematics : A Thinking Process of Artificial Animals P M V Subbarao Professor Mechanical Engineering Department Means to Control Displacement,

Real I. C. Engines Vs Ideal Models P M V Subbarao Professor Mechanical Engineering Department Ideal Cycles Set Performance Limits !!! Real Engines are.

Thermodynamic Analysis of Internal Combustion Engines P M V SUBBARAO Professor Mechanical Engineering Department IIT Delhi Work on A Blue Print Before.

The Role of Cylinder Geometry on Thermo- mechanical Process in I.C. Engines-2 P M V Subbarao Professor Mechanical Engineering Department Geometry is an.

Strategies to Achieve A Fast Cycle with High & Safe Peak Pressure in SI Engines P M V Subbarao Professor Mechanical Engineering Department Fuel Economy.

Influence of Design & Operational Parameters on Volumetric Efficiency of Engine P M V Subbarao Professor Mechanical Engineering Department Clues to Improve.

SIX STROKE DIESEL ENGINE

MEL713 – DESIGN OF I.C. ENGINES: COMPONENTS & SUB-SYSTEMS P M V Subbarao Professor Mechanical Engineering Department Laboratory & Design Practicals …..

Engine Size and Measurements

Thermodynamic Cycles Air-standard analysis is a simplification of the real cycle that includes the following assumptions: 1) Working fluid consists of.

SIX STROKE ENGINES VELOZETA MODEL. Introduction  Two different approaches of six stroke engines  First approach There is two additional strokes by the.

Selection of Geometric Ratios for I.C. Engines P M V Subbarao Professor Mechanical Engineering Department Control of Micro Actions through Macro Features…..

Bike Basics. What will we see today? A typical spec sheet Engine – What is it? Types of Engines – Two Stroke – Four Stroke – Wankel/Rotary Displacement.

The Role of Cylinder Geometry on Thermo- mechanical Process in I.C. Engines-1 P M V Subbarao Professor Mechanical Engineering Department Geometry is an.

Work Distribution Analysis of I.C. Engine Cycles P M V Subbarao Professor Mechanical Engineering Department Find true Scope for Development….

Maximization of Flow through Intake & Exhaust Systems

Four- Stroke Small Engines

Gasoline Engines Operation Energy and Power Energy is used to produce power. Chemical energy is converted to heat energy by burning fuel at a controlled.

Different Types of IC Engine Rated by their maximum horsepower Three Types –Reciprocating –Rotary –Sustained Combustion.

Prepared by : Pavan Narkhede

JAY DUDHELA Roll Num. - T13EC017 Enr. Num

Strategies for Complete Expansion in I.C. Engine P M V Subbarao Professor Mechanical Engineering Department Achieve Maximum Work Output….

The five stroke internal combustion engine Inventor & Patent owner: Dipl. Ing. Gerhard Schmitz.

ENGINE DESIGN AND OPERATION. ENGINE CLASSIFICATIONS n VALVE ARRANGEMENT n CAMSHAFT LOCATION n IGNITION TYPE n CYLINDER ARRANGEMENT n NUMBER OF CYLINDERS.

Copyright © 2016 by Pearson Education, Inc. All Rights Reserved Advanced Engine Performance Diagnosis, 6e James D. Halderman ADVANCED ENGINE PERFORMANCE.

THERMAL ENGINEERING (ME 2301 ) M.R.SWAMINATHAN Assistant Professor Department of Mechanical Engineering Anna University Chennai Chennai-25.

Kinematics Vs Transient Thermal Processes for I.C. Engines P M V Subbarao Professor Mechanical Engineering Department Intelligence to Control Method &

Operational Theory of Compression Small Engines Ag. 221.

Geometry Vs Engine Breathing P M V Subbarao Professor Mechanical Engineering Department Its not engine Volume, but Mass of air Decides the Power Output.

SIX STROKE ENGINE Anil Kumar C S6 Mechanical Roll No:05.

Lecture 2. Top Dead Center (TDC): Position of the piston when it stops at the extreme point away from the crankshaft. – Top because this position is at.

Chapter 20 Lecture 35: Entropy and the Second Law of Thermodynamics HW13 (problems):19.3, 19.10, 19.44, 19.75, 20.5, 20.18, 20.28,

Design of Engine Valves An Extended /Applied Fluid Mechanics…. P M V Subbarao Professor Mechanical Engineering Department.

FIVE STROKE I.C. ENGINE fi

Basic Engine Terms. Dead Center –The term identifies the relation between the positions of the crankshaft and the piston. When the piston is at its outward.

OPERATING PRINCIPLES OF PISTON ENGINES

Unit - 2 INTERNAL COMBUSTION ENGINES.

Understanding Principles of Operation of Internal Combustion Engines

The five stroke internal combustion engine

Strategies for Complete Expansion in I.C. Engine

Ideal but Practicable Cycles for I.C. Engines

Real I. C. Engines Vs Ideal Models

Mechanical Losses in An Engine

Engine Measurement CONNECTING ROD – effect on cylinder wall & piston

Transient Modeling of Current I.C. Engines

UNIT 3 – ENERGY AND POWER 3-6 UNIT 3 Topics Covered

SI Engine Cycle Actual Cycle Intake Stroke Compression Power Exhaust

Internal Combustion Basics

Thermodynamic Analysis of Internal Combustion Engines

THERMAL ENGINEERING-I

Presentation transcript:

Geometric & Kinematic Models for An I.C. Engine P M V Subbarao Professor Mechanical Engineering Department Creation of Infrastructure to Facilitate Thermodynamic Actions…..

Kinematics of Conventional I.C. Engine

Kinematics of Unconventional Piston Movement

Variable Piston Motion Kinematics

Free Piston Engine with Opposed Pistons

Free Piston Gas Generator

Free-Piston Engine With Linear Generator

p- v diagram for Free Piston Engine

The Dilemma of the Classical Engine Kinematics 1. High efficiency requires high expansion ratio 2. High power density requires low compression ratio BUT UNFORTUNATELY Expansion ratio = Compression ratio

How can we change a “ BUT UNFORTUNATELY = “ into an “ AND FORTUNATELY ≠ ” ?

The Unreasonable Bias A I R Combustion Products Ignition Intake Stroke FUEL Fuel/Air Mixture Compression Stroke Power Stroke Exhaust Stroke

A General Physician to A Team of Specialists Why not add an additional degree of freedom? Three times... “There is no reason to not try it!” Why not allow different cylinders to concentrate on different tasks? Why not add an additional engine stroke? Why not add an additional engine stroke?

In 2000, a new engine is born...

The software design...

The hardware manufacturing...

The New p-v Diagram

Six Stroke Engine Velozeta Six-stroke engine German Charge pump Crower six stroke engine Griffin six stroke engine Velozeta six-stroke engine Bajulaz six stroke engine

Kinematics of Conventional I.C. Engine

Engine Cylinder Geometry

Bore/Stroke Ratio Bore – to –Stroke Ratio

Geometry of Cylinder : A Primary Signature An engine is described as a square engine when it has equal bore and stroke dimensions, giving a bore/stroke value of exactly 1. By custom, engines that have a bore/stroke ratio of between 0.95 and 1.04 can be considered "square". An engine is described as under-square or long-stroke if its cylinders have a smaller bore than its stroke - giving a ratio value of less than 1. At a given engine speed, a longer stroke increases engine friction and increases stress on the crankshaft.

The smaller bore also reduces the area available for valves in the cylinder head, requiring them to be smaller or fewer in number. These factors favor lower engine speeds, under-square engines are most often tuned to develop peak torque at relatively low speeds. An under-square engine will typically be more compact in the directions perpendicular to piston travel but larger in the direction parallel to piston travel. An engine is described as over-square or short-stroke if its cylinders have a greater bore diameter than its stroke length, giving a bore/stroke ratio greater than 1.

An over-square engine allows for more and larger valves in the head of the cylinder, lower friction and lower crank stress. Due to the increased piston- and head surface area, the heat loss increases as the bore/stroke-ratio is increased excessively. These characteristics favor higher engine speeds, over- square engines are often tuned to develop peak torque at a relatively high speed. The reduced stroke length allows for a shorter cylinder and sometimes a shorter connecting rod, generally making over-square engines less tall but wider than under-square engines of similar engine displacement.