Distribution Statement C: Authorized for Government Agencies and their Contractors Only

SSP T&ME LCS Program Overview Michal Dusendang (812) 854-2358 michal.dusendang@navy.mil

Topics SSP TME LCS Organization SSBN SSGN Key Program Instructions Key Responsibilities SSP Technical Branches SSP TME Requirements Process NAVSEA Requirements Process

SSP LCS Organization INTERFACE ROLE SP201 J. SCHAEFER SP2016 M. RIVERA B. MORRISON NAVY TAMS EXECUTIVE BOARD SP20163 E. ZACHARIA TME LCS SP206 P. VOTH LOGISTICS SP502 A. HUNT STRATSYS SSGL UK CAL LAB NAVSEA 07T112 F. COLEMAN NSWC CORONA, MSD (CTM) R. FIGURRES UII (CDM) O. ROBINSON NSWC CRANE (CSM) R. ALLEN SWFLANT/PAC (TSBs) J. LANGE / S. SCHAFER NSWC CORONA (QAM) P. THORNBERRY

SSBN Fourteen Ohio-Class SSBNs Notional Schedule: Calibration Support: Eight home ported in Silverdale, WA Six home ported in Kings Bay, GA Notional Schedule: 21 day maintenance period at home port (Silverdale, WA or Kings Bay, GA), 90 Day deployment. Two Crews (Blue/Gold) Calibration Support: Calibration exchanges of portable T&ME conducted during 21 Day maintenance period – 100% portable T&ME calibrated at all times SWFPAC/SWFLANT Navy Calibration Laboratories support/coordinate installed and installed removable “I” Level T&ME calibration support.

SSGN First Four Ohio-Class SSBNs converted to SSGN Notional Schedule: USS Ohio, USS Michigan, USS Florida, USS Georgia Notional Schedule: 3-Month Major Maintenance Period at home port (Bremerton, WA or Kings Bay, GA), 15 month deployment, including 3 forward deployed voyage repair periods (VRP). Calibration Support: Two calibration exchanges of portable T&ME conducted during MMP (upon return from deployment, and just prior to departure) Calibration exchange of portable T&ME conducted at each VRP to lessen impact on forward labs. Short interval installed instruments supported by VR site laboratories USS Frank Cable (AS-40) – Guam NAVAIR Calibration Laboratory – Diego Garcia

Key Program Instructions OPNAVINST 3960.16A (TMDE, ATS, METCAL) SSPINST 4200.7C (T&ME LCS Instruction) OPNAVINST 4000.57F (TRIDENT Logistics Support) OD63913 (METPRO) OD55373A (T&ME LCS Procedures) OD55551 (SSBN Substitution Guide) OD64498 (SSGN Substitution Guide) OD65701 (Calibration Support Procedures for SSGN Forward Deployment)

Key Responsibilities for LCS SSPINST 4200.7C (T&ME LCS Instruction) Paragraph 3.a T&ME covered by this instruction… (1) All SWS, AWS and non-SWS/AWS GPTE, SPTE, GPS and SPS onboard SSBN/SSGN Paragraph 7 Responsibilities… f. NAVSEA and SPAWAR shall: Submit data sheets Outfit and replace non-SWS T&ME (excluding exchange pool) Provide support for new requirements (procedures, intervals, equipment) Provide maintenance documentation to NSWC Crane Provide authorized substitute information for OD55551 Ensure that NAVSEA resources (e.g., provision of authorized onboard FCA portable calibrators, audit of FCAs, evaluation and certification of FCAs, provision of “O” level calibration procedures)….and notify SSP when changes are planned.

SSP Technical Branches INSTRUMENTATION SUBSYSTEM INTERSTATE ELECTRONICS CORP NAVIGATION SUBSYSTEM N FIRE CONTROL SUBSYSTEM LMNE&SS/BOEING E GENERAL DYNAMICS ADVANCED INFORMATION SYSTEMS W NAVSEA/SP21 S SP22 SP28 LAUNCHER SUBSYSTEM NORTHROP GRUMMAN MARINE SYSTEMS SUBMARINE SSBN/SSGN GENERAL DYNAMICS ELECTRIC BOAT CORP. REENTRY SUBSYSTEM LOCKHEED MARTIN SPACE SYSTEMS COMPANY 59 SSBN SSP T&ME Requirements = ~ 104 pieces equipment 251 SSBN NAVSEA T&ME Requirements = ~ 708 pieces equipment SP23 SP27 GUIDANCE SUBSYSTEM TRIDENT MISSILE LOCKHEED MARTIN SPACE SYSTEMS COMPANY CHARLES STARK DRAPER LABORATORIES, et al

SSP Requirements Process Originator (generally contractor) initiates T&ME Requirement (Data Sheet) via web site https://tmecranrdte.navy.mil

SSP Requirements Process Data Sheet Identifies: Originator and Approving Official (SSP or NAVSEA Cog) New, Revised or Cancelled Requirement SPTE or GPTE Specific Model, Accessories, Authorized Substitutes chosen from OD 54585 Selection List Procurement Required and by who Calibration Support (Completed by MSD) Repair Support Allocation (SSBN, Work Center, Qty, Prime System) Procedural Documents for Requirement (MRC, SMP, Tech Manual, RPM, etc.)

SSP Requirements Process

SSP Requirements Process Electronic Data Sheet Routing Process Flow Originator Creates Designated Government Rep Approves NSWC Crane Review Ensure proper TME selection and non-proliferation Update allowance documentation, initiate procurement, update OD55551 (SSBN Substitution Guide) NSWC Corona Review Determine calibration support level, update METRL, identify ICP

SSP Requirements Process

NAVSEA Requirements Process Upload PMS FR Identify MRCs added, deleted or changed Identify T&ME impact Run comparison routine Cancel Requirement and Remove T&ME if required New Requirement Link Requirement to Data Sheet No Yes Generate “Matrix” of Data Sheet requirements Proliferation of T&ME Obviously the data sheet process is in an ideal world, that does not exist. To ensure changing requirements are captured, NSWC Crane reviews both SSP and NAVSEA maintenance documentation for portable T&ME impacts. The intent of the process is to ensure the sailor has the equipment to perform the procedure, remove equipment not required and ensure calibration support in place. Initiate Data Sheet No Yes Use Equipment Onboard

NAVSEA Requirements Data

T&ME Matrix

NAVSEA 08 Requirements Process BPMI generate new requirements (Data Sheets) NAVSEA 08 approve requirements NAVSEA 08 determine revised or cancelled requirements BPMI procure initial outfitting and exchange pool NSWC Crane push requirements to exchange pool/boats (need schedule) NSWC Crane update GPTE Addendum with NAVSEA 08 SCAT requirements NAVSEA 08 remove SCAT requirements from QCOSAL? NSWC Crane update “Matrix”

Questions?