Amplitude modulation is the process in which amplitude of the high frequency carrier wave is varies in accordance with the instantaneous value of modulating.

Slides:



Advertisements
Similar presentations
Analog Communications
Advertisements

Principles of Electronic Communication Systems
BEC/ECE/TSR Angle Modulation. BEC/ECE/TSR Contents  Properties of Angle (exponential) Modulation  Types –Phase Modulation –Frequency Modulation  Line.
Z. Ghassemlooy Angle Modulation Professor Z Ghassemlooy Electronics & IT Division Scholl of Engineering Sheffield Hallam University U.K.
Frequency modulation and circuits
Principles of Electronic Communication Systems Second Edition Louis Frenzel © 2002 The McGraw-Hill Companies.
Signal Encoding Techniques (modulation and encoding)
ANGLE MODULATION CHAPTER 3 Review on Part 1 Part 2
1 Modulations/demodulations in Transmitters/Receivers Amplitude modulation (AM) Angle modulation – Frequency, phase.
Amplitude Modulation Wei Li CSULB May 22, 2006.
Principles of analogue modulation
Lecture 3 Data Encoding and Signal Modulation
Angle Modulation Objectives
Angle Modulation – Frequency Modulation
Angle Modulation.
COMMUNICATION SYSTEM EECB353 Chapter 3(II) ANGLE MODULATION
ANGLE MODULATION 1. Introduction 2 Another class of modulation methods are frequency and phase modulation which referred to as angle- modulation methods.
Chapter 2 : Amplitude Modulation (AM) Transmission and Reception
AMPLITUDE MODULATION (AM)
COMMUNICATION SYSTEM EEEB453 Chapter 2 AMPLITUDE MODULATION
Fundamentals of Frequency Modulation
Radio Communication SL – Option F.1. Radio communication includes any form of communication that uses radio (EM) waves to transfer information –TV, mobile.
COMMUNICATION SYSTEM COMMUNICATION :
PRINCIPLES OF COMMUNICATION
Chapter 4. Angle Modulation
Prepared by Sam Kollannore U. Lecturer, Department of Electronics M.E.S.College, Marampally, Aluva-7.
Lecture 1B (01/07) Signal Modulation
ELECTRONIC COMMUNICATIONS A SYSTEMS APPROACH CHAPTER Copyright © 2014 by Pearson Education, Inc. All Rights Reserved Electronic Communications: A Systems.
© 2008 The McGraw-Hill Companies 1 Principles of Electronic Communication Systems Third Edition Louis E. Frenzel, Jr.
Eeng Chapter 5 AM, FM, and Digital Modulated Systems  Phase Modulation (PM)  Frequency Modulation (FM)  Generation of PM and FM  Spectrum of.
NARROW-BAND FREQUENCY MODULATION
Chapter 4. Angle Modulation
COMMUNICATION SYSTEMS (5marks)
Frequency Modulation ECE 4710: Lecture #21 Overview:
EET260 Frequency Modulation. Modulation A sine wave carrier can be modulated by varying its amplitude, frequency, or phase shift. In AM, the amplitude.
Amplitude/Phase Modulation
 To define and explain frequency modulation (FM) and phase modulation (PM)  To analyze the FM in terms of Mathematical analysis  To analyze the Bessel.
Part 1 Principles of Frequency Modulation (FM)
CHAPTER 2 AMPLITUDE MODULATION (AM). Principles of AM Definitions:  The process of changing the amplitude of a relatively high frequency carrier signal.
Principles & Applications
Chapter 5: Analog Transmission Converting digital data to a bandpass analog signal is traditionally called digital-to-analog conversion. Converting a low-pass.
ANGLE MODULATION CHAPTER 3. ANGLE MODULATION Part 1 Introduction.
4-3-3 Frequency Modulation.. Learning Objectives:At the end of this topic you will be able to; sketch, recognise and analyse the resulting waveforms for.
AM, FM, PM.
Eeng Chapter 5 AM, FM, and Digital Modulated Systems  Phase Modulation (PM)  Frequency Modulation (FM)  Generation of PM and FM  Spectrum of.
Principles of Electronic Communication Systems. Chapter 5 Fundamentals of Frequency Modulation.
Chapter 6 Tutorial 6.
ANGLE MODULATION CHAPTER 3. ANGLE MODULATION Part 1 Introduction.
Modulation. Carrier waves We have seen already that ELECTROMAGNETIC WAVES travel from their source around the world in a variety of ways according to.
Modulation Techniques ( 24 marks)
Angle Modulation Part 2 FM Bandwidth Power distribution of FM
Principles of Electronic Communication Systems
Analog Communications
UNIT – II ANGLE MODULATION (Part -1/2) Prepared by:
Chapter 3 ANGLE MODULATION
CHAPTER 3 Frequency Modulation
Principles of Electronic Communication Systems
FREQUENCY MODULATION “The process of changing the frequency of a carrier wave in accordance with the AF signal.” The Chapter includes: Wave Forms Theory.
Amplitude Modulation.
PRINCIPLES OF COMMUNICATION
AMPLITUDE MODULATION (AM)
FREQUENCY MODULATION “The process of changing the frequency of a carrier wave in accordance with the AF signal.” The Chapter includes: Wave Forms Theory.
PRINCIPLES OF COMMUNICATION
Mr. Haneef Khan Department of Computer Networks College of CS&IS
Signal Transmission and Channel Bandwidth
FREQUENCY MODULATION “The process of changing the frequency of a carrier wave in accordance with the AF signal.” The Chapter includes: Wave Forms Theory.
AMPLITUDE MODULATION (AM)
Amplitude Modulation By Dr. Vaibhav Jain Associate Professor, Dept. of Physics, D.A.V (PG) College, Bulandshahr, U.P., India.
Communication Theory- I Course Code:17 EC 2206 Dr. G V Subbarao Professor Department of Electronics and Communication Engineering K L University.
Presentation transcript:

Amplitude modulation is the process in which amplitude of the high frequency carrier wave is varies in accordance with the instantaneous value of modulating signal. EXPRESSION FOR AMPLITUDE MODULATED WAVE Let the modulated signal be represented as e m = Em sinw m t …(1) And the carrier signal be represented as. e c = Ec sinw c t … (2) “Depth of modulation” (m) or the “modulation index” is given by m= Em/Ec Now the amplitude of the modulated signal is given by A=Ec + e m Let the modulated signal be represented as e m = Em sinw m t …(1) And the carrier signal be represented as. e c = Ec sinw c t … (2) “Depth of modulation” (m) or the “modulation index” is given by m= Em/Ec Now the amplitude of the modulated signal is given by A=Ec + e m

= Ec + E m sinw m t = Ec +m Ec sinw m t = Ec [1+m sinw m t] … (3) Thus amplitude modulated signal can be represented in time domain as E = A sin0 E= A sinw c t = Ec [1+m sinw m t]* sinw c t = Ec sinw c t +mEc sinw c t sinw m t = E c sinw c t +(mEc /2)*2 sinwct sinwmt = Ec sinwct +(mEc /2) [cos( w c +w m )t + cos( w c -w m )t] …(4) Thus it has been shown that the equation of an amplitude modulated wave contains three terms. The first term is identical to equation (2) and represent the the unmodulated carrier. It is thus apparent that the process of amplitude modulation has the effect of adding term to the unmodulated wave, rather than changing it. = Ec + E m sinw m t = Ec +m Ec sinw m t = Ec [1+m sinw m t] … (3) Thus amplitude modulated signal can be represented in time domain as E = A sin0 E= A sinw c t = Ec [1+m sinw m t]* sinw c t = Ec sinw c t +mEc sinw c t sinw m t = E c sinw c t +(mEc /2)*2 sinwct sinwmt = Ec sinwct +(mEc /2) [cos( w c +w m )t + cos( w c -w m )t] …(4) Thus it has been shown that the equation of an amplitude modulated wave contains three terms. The first term is identical to equation (2) and represent the the unmodulated carrier. It is thus apparent that the process of amplitude modulation has the effect of adding term to the unmodulated wave, rather than changing it.

Modulation index can be practically can be calculated measured using two method. Using an AM signal. Using an trapezoidal display. Carrier signal Modulating signal Modulator CRO

(a) Modulating signal (b) Carrier signal tt t E max E min EcEc EmEm EmEm (c) Amplitude modulated signal

Q.1) M = Emax-Emin Emax+Emin Sol. M=Em/Ec m = E max - E min /2 ….1 Ec=E max - Em =Emax -( Emax-Emin/2 ) =Emax+Emin/2 …2 Dividing (1) by (2) M = Emax-Emin …3 Emax+Emin Equation (3) standard method of evaluating modulation index Q.1) M = Emax-Emin Emax+Emin Sol. M=Em/Ec m = E max - E min /2 ….1 Ec=E max - Em =Emax -( Emax-Emin/2 ) =Emax+Emin/2 …2 Dividing (1) by (2) M = Emax-Emin …3 Emax+Emin Equation (3) standard method of evaluating modulation index

Modulated signalAM signal t EmEm EcEc A B

In this method the Am signal is connected vertical deflection and the modulation signal is applied to the horizontal deflection plate of the oscilloscope. The display on the screen of oscilloscope is trapezoidal as shown in fig. A=2(Ec + Em) ……1 B=2( Ec-Em) ……2 Adding (1) and (2) A+B=4Ec Ec=(A + b) / 4 ……3 subtracting (1) and (2) A-B=4Em E m = (A-B) / 4 …….4 Modulation index m f = E m / E c = (A-b) / ( A+b ) In this method the Am signal is connected vertical deflection and the modulation signal is applied to the horizontal deflection plate of the oscilloscope. The display on the screen of oscilloscope is trapezoidal as shown in fig. A=2(Ec + Em) ……1 B=2( Ec-Em) ……2 Adding (1) and (2) A+B=4Ec Ec=(A + b) / 4 ……3 subtracting (1) and (2) A-B=4Em E m = (A-B) / 4 …….4 Modulation index m f = E m / E c = (A-b) / ( A+b )

Relative Power Distribution in AM Wave It is clear that modulated carrier wave contain more power as compared to unmodulated wave became of fact it contain two or more side band. The total power will depend upon the modulation index. P t = E c + E LSB + E USB ………….(1) R R R Where all the voltage signal have r.m.s value and R represents the antenna resistance. 222 P c = (E c / ) R =Ec /2R ……………(2) Similarly P lsb = P usb = [ (m Ec/2) / 2 ] = m Ec / 8R ………(3)

Putting the value of (2) and (3) in equation (1). Then result is : The maximum power in the AM corresponding to m=1 is P t = 1.5 Pc. This is important that relevant amplifier must be capable of handling without distortion. Current Calculation Let I c be the unmodulated carrier current and I t be the modulated current r is the resistance in which the current flow. P t / P c = I t R / I c R = [ 1 + m /2 ] I t / I c = 1 + m / 2 I t = I c 1+ m / 2 2 P t = P c [ 1 + m / 2]

If the frequency of the carrier is made to varying in accordance with instantaneous Value of the modulating signal, the process is called FM. Expression: In FM the frequency of the carrier varies the amount by which the carrier frequency and varied from its unmodulated value is called deviation. And the deviation is perpendicular to the Instantaneous value of modulating signal. The instantaneous value of frequency of the modulated carreier is given by: f = f c + f c k f E m cosw m t = f c [1 + k f E m cosw m t ] ……..(1) F c = unmodulated carrier frequency. K f = proportionality constant E m cosw m t = Instantaneous modulated voltage If the frequency of the carrier is made to varying in accordance with instantaneous Value of the modulating signal, the process is called FM. Expression: In FM the frequency of the carrier varies the amount by which the carrier frequency and varied from its unmodulated value is called deviation. And the deviation is perpendicular to the Instantaneous value of modulating signal. The instantaneous value of frequency of the modulated carreier is given by: f = f c + f c k f E m cosw m t = f c [1 + k f E m cosw m t ] ……..(1) F c = unmodulated carrier frequency. K f = proportionality constant E m cosw m t = Instantaneous modulated voltage

Maximum Frequency deviation f min = fc (1-kE m ) f max = fc (1+kE m )[] = f max – f c = f c – f min = k f E m f c ……….2 Considering again equation (1) f = f c [1 + k f E m cosw m t ] w = w c [1 + k f E m cosw m t ] But angular velocity W= do / dt O = wdt Put the value of w O = w c [1 + k f E m cos w m t ] dt = w c t + w c k f E m sinw m t wm Maximum Frequency deviation f min = fc (1-kE m ) f max = fc (1+kE m )[] = f max – f c = f c – f min = k f E m f c ……….2 Considering again equation (1) f = f c [1 + k f E m cosw m t ] w = w c [1 + k f E m cosw m t ] But angular velocity W= do / dt O = wdt Put the value of w O = w c [1 + k f E m cos w m t ] dt = w c t + w c k f E m sinw m t wm f min f max fcfc

O(t) = w c t + sinw m t …………(3) from 2 fm The carrier wave efmt may be written as ef m (t) = E c sinO(t) Put the value of O(t) in above equation ef m (t) = E c sin (w c t + sinw m t ) ………..(4) fm The modulation index of FM Mf = Max frequency deviation = ……….(5) Modulating frequency fm From equation (4) and (5) ef m (t) = E c sin (w c t + M f fm sinw m t ) ………..(4) fm ef m (t) = E c sin (w c t + M f sinw m t ) Ans. O(t) = w c t + sinw m t …………(3) from 2 fm The carrier wave efmt may be written as ef m (t) = E c sinO(t) Put the value of O(t) in above equation ef m (t) = E c sin (w c t + sinw m t ) ………..(4) fm The modulation index of FM Mf = Max frequency deviation = ……….(5) Modulating frequency fm From equation (4) and (5) ef m (t) = E c sin (w c t + M f fm sinw m t ) ………..(4) fm ef m (t) = E c sin (w c t + M f sinw m t ) Ans.

The Expression for FM is not simple. It is complex since, it is a sine of sine function. The only way to solve this equation is using Bessel’s Function. By using Bessel’s Function. The equation for FM wave can be expanded. As follows. efm = s(t)= Ec { jo (M f ) sinw c t } + j 1 Mf { sin( w c +w m )t – sin (w c -w m )t } +j 2 M f { sin(w c +2w m ) t + sin (w c -2w m )t }+ j 3 Mf { sin( w c +3w m )t – sin (w c -3w m )t } + j 4 Mf { sin( w c +4w m )t – sin (w c -4w m )t } +………….(*) 1.The FM wave constant of carrier. The first term in equation the carrier. 2.FM consist of infinite no. of side band. All terms except first term. 3.The amplitude of the carrier and the side band depend is depends on ‘j’ coefficient. The value of these coefficient can be term the graph. The Expression for FM is not simple. It is complex since, it is a sine of sine function. The only way to solve this equation is using Bessel’s Function. By using Bessel’s Function. The equation for FM wave can be expanded. As follows. efm = s(t)= Ec { jo (M f ) sinw c t } + j 1 Mf { sin( w c +w m )t – sin (w c -w m )t } +j 2 M f { sin(w c +2w m ) t + sin (w c -2w m )t }+ j 3 Mf { sin( w c +3w m )t – sin (w c -3w m )t } + j 4 Mf { sin( w c +4w m )t – sin (w c -4w m )t } +………….(*) 1.The FM wave constant of carrier. The first term in equation the carrier. 2.FM consist of infinite no. of side band. All terms except first term. 3.The amplitude of the carrier and the side band depend is depends on ‘j’ coefficient. The value of these coefficient can be term the graph.

For equation j1(Mf) denotes the value of j1 for the particular value of Mf written inside the bracket. M f jo j1 j In Mf wave, the total transmitted power always remain constant. It is not dependent upon modulation index. The region for this is that the amplitude of FM wave is constant. P t =( a / 2) = A Where ’A’ peak amplitude of FM wave.It is equal to Pt = A where R =1 For equation j1(Mf) denotes the value of j1 for the particular value of Mf written inside the bracket. M f jo j1 j In Mf wave, the total transmitted power always remain constant. It is not dependent upon modulation index. The region for this is that the amplitude of FM wave is constant. P t =( a / 2) = A Where ’A’ peak amplitude of FM wave.It is equal to Pt = A where R =1 2 2 RR 2 R

1) Amplitude of AM wave will change With modulating voltage. 2) Transmitted power is dependent on the Modulation index. 3) Carrier power and one side band power is useful. 4) AM receiver are non immune to noise. 5) It is not possible to decrease noise further by increasing deviation Amplitude of Fm is constant. It is independent of modulation index. Transmitted power remain constant. It is interdependent on the Modulation index. All the transmitted power is useful. They are immune to noise. It is possible to decrease noise further by increasing deviation

Bandwidth = 2( + fm ). BW depends on. BW is much less than FM. Ground wave and sky wave propagation is used. Therefore large area is concerned. AM equipments for modulation are less complex. No. of side band will be two and more constant. Bandwidth = 2 f m BW is large hence wide channel is required. Space wave is used for propagation so radius of transmission is limited. FM transmission and reception the equipment are complex. NO. of side band having significant amplitude depends upon modulation index.

FM S(t) = Ec sin( w c t + m f sinw m t) Frequency modulation is proportional to modulating voltage. M f is proportional to modulating voltage as well as the modulating frequency. It is widely used. It is possible to receive FM on PM receiver Noise immunity is better than AM an PM S(t) = Ec sin( w c t + m p sinw m t) Phase modulation is proportional to modulating voltage. M p is proportional only to modulating voltage. Used in some mobile system. It is possible to receive PM on FM receiver. Noise immunity is better than AM but worst than PM PM