1 Hands-on: Heater Circuit Kit includes: 3 9 Volt batteries (for flight only) 1 Perf Board 3Ceramic Resistors (4 5W) 39 V connectors 1 White wire 1.

Slides:



Advertisements
Similar presentations
Building a Weather Station for a Near-Space Payload AEM 1905: Spaceflight with Ballooning University of Minnesota.
Advertisements

The circuit shows working model of two way traffic light system .
Assembly Manual Mike Fortney 04/09/2004 CricketSat Receiver.
CricketSat Receiver Assembly Instructions This is the instruction slides for the assembly of a receiver board. It would be a good idea to review soldering.
CricketSat Assembly.
Building a Heater Circuit for a Near-Space Payload AEM 1905: Spaceflight with Ballooning University of Minnesota.
Wiring Color Codes for McLean County 4-H Projects.
Building a Pressure/Temperature Weather Station (Sensor Pack) AEM 1905, Fall 2008.
Electronics Merit Badge Class 4 5/17/2015Electronics Merit Badge Class National Scout Jamboree1.
Dual H-Bridge L298N Breakout Board By Marcelo Moraes BIGDOG1971.
Colorado Space Grant Consortium Gateway To Space ASEN / ASTR 2500 Class #06 Gateway To Space ASEN / ASTR 2500 Class #06 T-58.
Assembly Manual Mike Fortney 04/02/2006 CricketSat LC Receiver.
Assembly Manual Mike Fortney 04/02/2006 CricketSat Receiver.
Colorado Space Grant Consortium Timing Circuit HW #4 Class #07 Timing Circuit HW #4 Class #07.
1 Student Hands On Training I (2009) Additional AVR Modifications For BalloonSat Flight Additional AVR Modifications For BalloonSat Flight.
Colorado Space Grant Consortium Gateway To Space ASEN / ASTR 2500 Class #06 Gateway To Space ASEN / ASTR 2500 Class #06.
1 Student Hands On Training I (2007) Timing Circuit & Camera Integration Timing Circuit & Camera Integration.
You will need the following parts from your kit: 1.Breadboard ohm resistor (brown, black, brown, gold) 3.1 LED (light emitting diode) 4.1 Potentiometer.
SpectraSonde Assembly. What is the SpectraSonde? Reads temperature, pressure, and humidity data from the atmosphere. The SpectraSonde doesn’t fly like.
Basic Electricity Facts and Diagrams. Romex Types Determine your need to determine the type of Romex needed Gage Size of the wire (common = 12 or 14)
Solar Energy Station Directions. Making a Solar-Powered Circuit 1.Make sure your solar panel is in direct sun. 2.Get the clear LED bulb. 3.Use a red jumper.
Lighting and Wiring Services
George Washington University DC Circuits Lab Professor Ahmadi ECE 002.
Using a Multimeter McTigue Junior High Technology Ed. Click Here
Speaker Foundations of Technology Speaker © 2013 International Technology and Engineering Educators Association, STEM  Center for Teaching and Learning™
Wiring the Control Box Battery Conductor(s) Resistor.
Experiments Day 1 & 2 Resistors, Potentiometers and Photocells.
Is this a series circuit or a parallel circuit?
ELECTRONICS AND SAFETY Scarlett, Dash, Sam, Ashley, and Eric.
Building a Weather Station for a Near-Space Payload AEM 1905: Spaceflight with Ballooning University of Minnesota.
Discovery Kits: Electricity. 1.5 V Battery Batteries in series Closed switch Open switch V Motor Components.
Camera Pieces in Box TV Battery Battery Charger Camera Sun shade.
With a knowledge of how to connect cells in parallel and series, we can figure out how to arrange batteries to deliver a desired voltage, and in some cases,
 Source of voltage difference ◦ Battery, outlet  At least one device that uses the electrical energy ◦ Radio, microwave, clock, etc  Conductor that.
BY: ELIZABETH KHOSRAVI IGCSE PHYSICS SERIES AND PARALLEL CIRCUITS.
Complex Circuits Notes Series Circuit + Parallel Circuit = Complex Circuit.
Computer Hardware Technology
How an NPN Transistor Works
Front view LED’s pushed into place Buzzer bolted on Fuse holder bolted on.
Colorado Space Grant Consortium Gateway To Space ASEN / ASTR 2500 Class #06 Gateway To Space ASEN / ASTR 2500 Class #06.
RC Circuits MS&T Physics 2135, Lab O4. Objectives  Measure the time constant of a series RC circuit.  Determine C Note: You will be using a 1F, 5V electrolytic.
Dual Sparkle Circuit Green connections are wires – they can be any colour. Make sure all + and - connections match up. Make sure the larger battery terminal.
Norwood Elementary Science SCHEMATIC DIAGRAM SYMBOLS.
What materials are the best conductors. Possible Materials Aluminum Foil Paper Clips Wood Plastic Rubber Bands String.
Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.
Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.
SeaPerch Electrical System. Electrical System Overview Assemble the control box. Make the Cat5 connector. Wire the motors to the tether. Wire the control.
© NTScience.co.uk 2005KS3 Unit 7j - Circuits 1 Circuits.
How does Energy Move? Lab setup: Goal: SI learning Goal:
Set up your circuit board 2 batteries, bulb, switch, and variable resister.
LED Flashlight.
Light Emitting Diode: LED
SeaPerch Electrical System
The Relay based Multiplexer
Student Hands On Training Workshop (SHOT 2007)
Lesson 4 Electricity Part 3.
Building a Heater Circuit for a Near-Space Payload
Schematic Diagrams: Electrical Component Symbols
You have 5 minutes to check the resistors you have done.
Arduino Switch Soldering
Basic Electronics Part Two: Electronic Components.
Dual H-Bridge L298N Breakout Board By Marcelo Moraes BIGDOG1971.
How a Speaker Works.
How a PNP Transistor Works
How an NPN Transistor Works
Project: Wiring a Building
Bell Work: Series vs. Parallel
SeaPerch Electrical System
Magic Wand.
Presentation transcript:

1 Hands-on: Heater Circuit Kit includes: 3 9 Volt batteries (for flight only) 1 Perf Board 3Ceramic Resistors (4 5W) 39 V connectors 1 White wire 1 Blue wire 1 Red wire 1 Black wire

2 Hands-on: Heater Circuit 1. Set out kit

Front:Back: 3 Hands-on: Heater Circuit 2. Layout Resistors on Perf Board

4 Hands-on: Heater Circuit 3. Fold the leads of two of the resistors and solder them together as shown:

5 Hands-on: Heater Circuit 4. Clip the leads:

6 Hands-on: Heater Circuit 5. Repeat steps 3 and 4 so the resistors are soldered in series, using the leads of the resistors 4Ω4Ω4Ω4Ω4Ω4Ω

7 Hands-on: Heater Circuit Your circuit should look like this:

8 Hands-on: Heater Circuit 6. Twist all the Red wires from the 9V connector together and solder them to the single red wire in your kit

9 Hands-on: Heater Circuit 7. Twist all the Black wires from the 9V connector together and solder them to the single black wire

10 Hands-on: Heater Circuit 8. Check continuity for all “-” and “+” terminals to each other

11 Hands-on: Heater Circuit 9. Check continuity for all “+” terminals of the battery with the end of the single RED wire 10. Check continuity for all “-” terminals of the battery with the end of the single BLACK wire

12 Hands-on: Heater Circuit 11. Put electrical tape on solder joints

13 Hands-on: Heater Circuit 12. Solder the single RED wire from 9V connector to one end of the resistor string and the WHITE wire to the other end of the resistor string 4Ω4Ω 4Ω4Ω 4Ω4Ω *Green boxes are battery connectors

14 Hands-on: Heater Circuit 13. Solder the switch in between the black wire and the white wire 4Ω4Ω4Ω4Ω4Ω4Ω

15 Hands-on: Heater Circuit 14. Test your finished Heater by turning on the switch and putting your finger on the resistors – if they get warm, you’re done. If they don’t, check continuity at the following points: 4Ω4Ω 4Ω4Ω 4Ω4Ω