Simply easy! TM XUSL2E/4E light curtains Pilot light ? How to provide a signal to a pilot light or to a PLC input.

Slides:

Advertisements

Similar presentations

Masterclass 2001: Safety Integrated Excellencein Automation&Drives: Siemens Folienthema/Folie 1/Jahreszahl Name & Department AS-Interface Safety now included!

Advertisements

Programming with Ladder Logic

Programming Logic Controllers

Motor Starter Coordination

HYDRAULICS & PNEUMATICS

TPP-TCOMM-17/29/05#1TeleComm™ Control Panels TPP-TCOMM-17/29/05#1.

In this presentation you will:

ZE Ready Electric board. Schneider Electric 2 - VE – Bosquillon – Functionality of Electrical board ●Safety and protections ●User protections ●Equipment.

©2011, The McGraw-Hill Companies, Inc. Chapter 4.

Graphic Symbol Location 1. DIN Terminal X52 The machine is powered by electricity using copper cable with 5 wires (3 phase wires + neutral wire +

ROTHENBUHLER ENGINEERING

Simply easy! TM XUSL4E light curtain - cabling - How to replace the obsolete XUSLB/D by the new XUSL4E and re-using the old cabling - Old & new parts use.

Slide 1 / 35 P&T - GPS - Training PhB - 01_TECH_TeSys_U_controller_ en 06/2004 Presentation of the range Composition of the controller  Control base 

Engineer Training Electrical System Overview and Requirements.

DC Motors, Stepper Motors, H-bridges DC Motors Stepper Motors Motor Control Circuits – Relays – H-bridges.

Chapter 8 Output Modules.

PLC Fundamentals Module 2: Hardware and Terminology.

One solution, many application Integrated Electronic Solution PowerSupply Flex.

Module 2: Hardware and Terminology

Section 4: Electric Motors

Engineer Training UV Electrical Cabinet (16 and above) TJ8300 / TJ8500 UV Electrical Cabinet (Machines 16 and above)

SISTEMA Example One. Schneider Electric – Sistema Example 1 – June Example 1: Start/Stop Facility with Emergency Stop Device Circuit Diagram.

Overview of the 1.

SISTEMA Example Two. Schneider Electric – Areva D Acquisition – June Example 2: Safe stopping of a PLC-driven drive with emergency stop – Category.

Electro-Pneumatics Module 1

© Reference New safety system for Arc Welding products and systems.

Industrial Machine Control

Sensors. This is a set of transmitter and receiver in one of the photoelectric sensor. Detection distance can be adjusted according to the requirements.

JANUS TYPE 4 SAFETY LIGHT CURTAINS applications.

4 May I/O Control. 4 May What is I/O Control? A Doors feature that allows you to program input events to drive output responses – for example:

XS26-2 Expandable Safety Controller.

TRISHUL Winding Solutions Pvt Ltd. RELAY COIL A relay is an electrical switch that uses an electromagnet for automatically off/on the switch instead of.

Module 1: Introduction to PLC

Electrical Distribution Training

Control Technology and Automation

By Anthony Moody Rhys Porter Nicolas Wilson.  Background  Objectives  Design  Normal Operation  Logic  Failure  Issues and solutions  Improvements.

TRISHUL Winding Solutions Pvt Ltd. RELAY COIL A relay is an electrical switch that uses an electromagnet for automatically off/on the switch instead of.

AQ 100 Series Arc Flash Protection System. Characteristics of arc protection Speed, no intentional delays Sensitive, current set-points just above loads.

Engineer Training UV Electrical Cabinet (1-15) TJ8300 / TJ8500 UV Electrical Cabinet (Machines 1-15)

The 3 parts of an electronic system are :

Logic Functions and Symbols

SmartMQn Motor Horner APG, LLC September 9, 2008.

Prepared by: Engr. Qurban Ali Memon 11ES (SEC- 1 & 2)

Quick guide to ASIMON configuration For version 3.0 or greater SAFETY AT WORK Date: 3/18/2009.

SISTEMA Example Four.

the compact air control solution

PRESENTATION ON THE TOPIC By: Rahul agarwal. INTRODUCTION  Overload protection circuit are required in inverters and uninterrupted power supplies to.

Simply easy! TM XY2CC122 obsolete switch  XY2CC122 description  How to replace or cross-reference.

Start of Sales MSI-XXXB Safety Relays Plugable screw or spring-cage terminal blocks.

The Quality Control Company Quanti TM product series “Simplicity is the ultimate sophistication” - Leonardo da Vinci.

1 Comparison of 100-B and 100-D Contactors B Contactors.

Software Configurable Safety Relay

Module 1: Introduction to PLC

SLS 518 Single Beam Safety Light Barrier Type 4

CLOSED-LOOP MOTOR SPEED SENSOR & CONTROLLER

PLC Front Panel.

GROUND-FAULT GROUND-CHECK MONITOR

PLC Front Panel.

PLC Hardware Components.

PLC Front Panel.

PLC Front Panel.

PLC Front Panel.

Hardware integration and interfaces

Microscan3 Core – Technical Addendum

SISTEMA Example Three.

Presentation transcript:

Simply easy! TM XUSL2E/4E light curtains Pilot light ? How to provide a signal to a pilot light or to a PLC input

Telemecanique Sensors 2 - Technical support – April 17 th, 2015 XUSL2E/4E light curtains ●Alternative to supply a pilot light or a PLC signaling input ●No additional output integrated into the light curtain to provide such electrical signal ●External light or PLC input, how to energize it : ●Either by using directly the NC contact available in the FSD (final switch device) connected to the OSSD. ●Either by an external component, when a safety interface is used If it is associated to a safety relay, if possible use an optional output of this relay (or of the monitoring unit). Please check current compatibility of this output with the light or PLC input.

Telemecanique Sensors 3 - Technical support – April 17 th, 2015 XUSL2E/4E light curtains ●Pilot light ●Recommended colour According to the table 4 of the IEC standard (electrical equipment of machines), the yellow (or orange) colour is recommended. In this european standard, the red colour is dedicated for an action required in case of hazardous situation. ●Possible product selection in dia22mm ●Plastic pilot light in XB5A range (version integrated into XY2CE switch) ●Metal pilot light in XB4B range ●Monolithic plastic pilot light in XB7 range

Telemecanique Sensors 4 - Technical support – April 17 th, 2015 XUSL2E/4E light curtains ●Pilot light ●Examples of light units ●XB5AV ●XB7EV

Telemecanique Sensors 5 - Technical support – April 17 th, 2015 XUSL2E/4E light curtains ●How to supply the light in the stand-alone solution ●From the 2 nd NC contact of the CAD32* auxiliary contactor, with linked contacts ●Possible option : NC contact available on the instantaneous auxiliary contact block of the contactor

Telemecanique Sensors 6 - Technical support – April 17 th, 2015 XUSL2E/4E light curtains ●How to supply the light in the stand-alone solution ●K1 contactor detail, CAD32* used ●The light indicates the machine stop 0V +24Vdc K1 OSSD1 K1 K2 restart XUSL receiver

Telemecanique Sensors 7 - Technical support – April 17 th, 2015 XUSL2E/4E light curtains ●How to supply the light, in case of safety interface association ●From the XPS safety relay, using an auxiliary NC contact. Attached XPSAK example using the auxiliary NC output.