Eddy Viscosity Model Jordanian-German Winter Academy February 5 th -11 th 2006 Participant Name : Eng. Tareq Salameh Mechanical Engineering Department.

Slides:



Advertisements
Similar presentations
Boundary layer with pressure gradient in flow direction.
Advertisements

School of Mechanical, Aerospace & Civil Engineering Postgraduate Research Conference, PGR-MACE10 Performance of two k T -k L -ω models in a separation-induced.
Conservation Equations
Convection.
Louisiana Tech University Ruston, LA Slide 1 Time Averaging Steven A. Jones BIEN 501 Monday, April 14, 2008.
Turbulent Models.  DNS – Direct Numerical Simulation ◦ Solve the equations exactly ◦ Possible with today’s supercomputers ◦ Upside – very accurate if.
Lecture Objectives: Simple algorithm Boundary conditions.
Lecture 10 - Turbulence Models Applied Computational Fluid Dynamics
Boundary Layer Flow Describes the transport phenomena near the surface for the case of fluid flowing past a solid object.
..perhaps the hardest place to use Bernoulli’s equation (so don’t)
Advanced CFD Analysis of Aerodynamics Using CFX
LES of Turbulent Flows: Lecture 10 (ME EN )
1 MECH 221 FLUID MECHANICS (Fall 06/07) Tutorial 7.
Flow over an Obstruction MECH 523 Applied Computational Fluid Dynamics Presented by Srinivasan C Rasipuram.
Combining the strengths of UMIST and The Victoria University of Manchester Aspects of Transitional flow for External Applications A review presented by.
1 B. Frohnapfel, Jordanian German Winter Academy 2006 Turbulence modeling II: Anisotropy Considerations Bettina Frohnapfel LSTM - Chair of Fluid Dynamics.
CHE/ME 109 Heat Transfer in Electronics
Introduction to Convection: Flow and Thermal Considerations
Estimation of Prandtls Mixing Length
LES of Turbulent Flows: Lecture 3 (ME EN )
Transport Equations for Turbulent Quantities
Lecture of : the Reynolds equations of turbulent motions JORDANIAN GERMAN WINTER ACCADMEY Prepared by: Eng. Mohammad Hamasha Jordan University of Science.
FUNDAMENTAL EQUATIONS, CONCEPTS AND IMPLEMENTATION
Conservation Laws for Continua
Introduction to Convection: Flow and Thermal Considerations
CFD Modeling of Turbulent Flows
Chapter 9: Differential Analysis of Fluid Flow SCHOOL OF BIOPROCESS ENGINEERING, UNIVERSITI MALAYSIA PERLIS.
PTT 204/3 APPLIED FLUID MECHANICS SEM 2 (2012/2013)
1 LES of Turbulent Flows: Lecture 11 (ME EN ) Prof. Rob Stoll Department of Mechanical Engineering University of Utah Fall 2014.
Boundary Layer Laminar Flow Re ‹ 2000 Turbulent Flow Re › 4000.
Chapter 9 Turbulence Introduction to CFX.
Introduction to Fluid Mechanics
Governing equations: Navier-Stokes equations, Two-dimensional shallow-water equations, Saint-Venant equations, compressible water hammer flow equations.
1 MAE 5130: VISCOUS FLOWS Momentum Equation: The Navier-Stokes Equations, Part 2 September 9, 2010 Mechanical and Aerospace Engineering Department Florida.
Momentum Equations in a Fluid (PD) Pressure difference (Co) Coriolis Force (Fr) Friction Total Force acting on a body = mass times its acceleration (W)
Fluid Flows due to Pure Mechanical Forces… P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Construction of Navier-Stokes Equations.
Mass Transfer Coefficient
Chapter 6 Introduction to Forced Convection:
HEAT TRANSFER FINITE ELEMENT FORMULATION
© Fluent Inc. 12/18/2015 D1 Fluent Software Training TRN Modeling Turbulent Flows.
The Stability of Laminar Flows - 2
Convection in Flat Plate Boundary Layers P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi A Universal Similarity Law ……
Quantification of the Infection & its Effect on Mean Fow.... P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Modeling of Turbulent.
MECH 221 FLUID MECHANICS (Fall 06/07) Chapter 8: BOUNDARY LAYER FLOWS
INTRODUCTION TO CONVECTION
Analysis of Turbulent (Infected by Disturbance) Flows
THE BOUNDARY LAYER: AN INTRODUCTION  In a flow, the boundary layer represents a (relatively) thin layer of fluid that is nearest the solid boundary
Turbulence Modeling In FLOTRAN Chapter 5 Training Manual May 15, 2001 Inventory # Questions about Turbulence What is turbulence and what are.
 Swiss Mathematician and Physicist  Born in the early 1700s  Made mathematical applications to fluid mechanics.

1 CONSTITUTIVE RELATION FOR NEWTONIAN FLUID The Cauchy equation for momentum balance of a continuous, deformable medium combined with the condition of.
Turbulence Models Validation in a Ventilated Room by a Wall Jet Guangyu Cao Laboratory of Heating, Ventilating and Air-Conditioning,
Lecture Objectives: Define 1) Reynolds stresses and
1 LES of Turbulent Flows: Lecture 7 (ME EN ) Prof. Rob Stoll Department of Mechanical Engineering University of Utah Spring 2011.
Direct numerical simulation has to solve all the turbulence scales from the large eddies down to the smallest Kolmogorov scales. They are based on a three-dimensional.
Heat Transfer Su Yongkang School of Mechanical Engineering # 1 HEAT TRANSFER CHAPTER 6 Introduction to convection.
Avaraging Procedure. For an arbitrary quantity  the decomposition into a mean and fluctuating part can be written as.
Turbulent Fluid Flow daVinci [1510].
External flow: drag and Lift
Chapter 12-2 The Effect of Turbulence on Momentum Transfer
The Standard, RNG, and Realizable k- Models. The major differences in the models are as follows: the method of calculating turbulent viscosity the turbulent.
Objective Introduce Reynolds Navier Stokes Equations (RANS)
Chapter 4 Fluid Mechanics Frank White
Numerical Investigation of Turbulent Flows Using k-epsilon
Chapter 9: Differential Analysis of Fluid Flow
K-ε model, ASM model.
The k-ε model The k-ε model focuses on the mechanisms that affect the turbulent kinetic energy (per unit mass) k. The instantaneous kinetic energy k(t)
Objective Review Reynolds Navier Stokes Equations (RANS)
9th Lecture : Turbulence (II)
Objective Define Reynolds Navier Stokes Equations (RANS)
Presentation transcript:

Eddy Viscosity Model Jordanian-German Winter Academy February 5 th -11 th 2006 Participant Name : Eng. Tareq Salameh Mechanical Engineering Department University of jordan

Reynolds Averaged Navier-Stokes (RANS) Reynolds Averaged Navier-Stokes (RANS) The averaging procedure introduces additional unknown terms containing products of the fluctuating quantities, which act like additional stresses in the fluid. These terms, called ‘turbulent’ or ‘Reynolds’ stresses, are difficult to determine directly and so become further unknowns. Reynolds stress and the Reynolds flux These terms arise from the non-linear convective term in the un-averaged equations.

Reynolds Averaged Navier-Stokes (RANS) (Cont.) The Reynolds (turbulent) stresses need to be modeled by additional equations of known quantities in order to achieve “closure”. Closure implies that there is a sufficient number of equations for all the unknowns, including the Reynolds- Stress tensor resulting from the averaging procedure.

Reynolds Averaged Navier-Stokes (RANS) (Cont.) The equations used to close the system define the type of turbulence model Reynolds Averaged Navier Stokes (RANS) Equations. Type of turbulence model based on RANS (classical type) Eddy viscosity model (I) Reynolds stress model (II) Another type Large Eddy Simulation model Detached Eddy Simulation model

Eddy viscosity model One proposal suggests that turbulence consists of small eddies which are continuously forming and dissipating. Definition of eddy viscosity model. The eddy viscosity hypothesis assumes that the Reynolds stresses can be related to the mean velocity gradients and Eddy (turbulent) Viscosity by the gradient diffusion hypothesis, in a manner analogous to the relationship between the stress and strain tensors in laminar Newtonian flow.

Eddy viscosity model Here,  t is the Eddy Viscosity or Turbulent Viscosity. This has to be prescribed. Analogous to the eddy viscosity hypothesis is the eddy diffusivity hypothesis, which states that the Reynolds fluxes of a scalar are linearly related to the mean scalar gradient:

Eddy viscosity model Here,  t is the Eddy Diffusivity, and this has to be prescribed. The Eddy Diffusivity can be written : Where P rt is the turbulent Prandtl number. Eddy diffusivities are then prescribed using the turbulent Prandtl number.

Eddy viscosity model The above equations can only express the turbulent fluctuation terms of functions of the mean variables if the turbulent viscosity,  t, is known. Both the k-  and k-  two-equation turbulence models provide this variable. Subject to these hypotheses, the Reynolds averaged momentum and scalar transport equations become:

Eddy viscosity model where B is the sum of the body forces, µ eff is the Effective Viscosity, and Γ eff is the Effective Diffusivity, defined by, andis a modified pressure, defined by: whereis the bulk viscosity.

The Zero Equation Model Very simple eddy viscosity models compute a global value for µ t from the product of turbulent mean velocity scale, U t, and a a turbulence geometric length scale, l t using an empirical formula, as proposed by Prandtl and Kolmogorov Wheref  =0.01is a proportionality constant Because no additional transport equations are solved, these models are termed ‘zero equation’

The Zero Equation Model (Cont.) The velocity scale is taken to be the maximum velocity in the fluid domain. The length scale is derived using the formula: where V D is the fluid domain volume This model has little physical foundation and is not recommended.

Two-equation turbulence models (k-  and k-  ) are very widely used and much more sophisticated than the zero equation models. Both the velocity and length scale are solved using separate transport equations (hence the term ‘two- equation’) The turbulence velocity scale and the turbulent length scale are computed from the turbulent kinetic energy and turbulent kinetic energy and its dissipation rate respectively. Two Equation Turbulence Models

The k-  model k is the turbulence kinetic energy and is defined as the variance of the fluctuations in velocity.  is the turbulence eddy dissipation (the rate at which the velocity fluctuations dissipate) The k-  model introduces two new variables into the system of equations. The continuity equation is then:

and the momentum equation becomes: The k-  model (Cont.) where B is the sum of body forces. µ eff is the effective viscosity accounting for turbulence. is the modified pressure given by

The k-  model (Cont.) The k-  model, like the zero equation model, is based on the eddy viscosity concept, so that where µ t is the turbulence viscosity. The model k-  assumes that the turbulence viscosity µt is linked to the turbulence kinetic energy and dissipation via the relation Where C  =0.09

The k-  model (Cont.) The values of k and  come directly from the differential transport equations for the turbulence kinetic energy and turbulence dissipation rate:

The k-  model (Cont.) Where C ε1 =1.44, C ε2 =1.92,  k =1.0 and   =1.3 are constants. P k is the turbulence production due to viscous and buoyancy forces, which is modeled using: For incompressible flow,is small and the second term on the right side of equation does not contribute significantly to the production.

The k-  model (Cont.) For compressible flow,is only large in regions with high velocity divergence, such as at shocks. The term 3µ t in the second term is based on the “frozen stress” assumption. This prevents the values of k and  becoming too large through shocks.

The k-  model (Cont.) there are applications for which these models may not be suitable Flows with boundary layer separation. Flows with sudden changes in the mean strain rate. Flows in rotating fluids. Flows over curved surfaces. A Reynolds Stress model may be more appropriate for flows with sudden changes in strain rate or rotating flows, while the SST model may be more appropriate for separated flows.

Turbulent Recirculation Flow The k-  model (Cont.)

Buoyancy Turbulence If the full buoyancy model is being used, the buoyancy production term P kb is modeled as: and if the Boussinesq buoyancy model is being used, it is:

The RNG k-  Model The RNG k-  model is based on renormalisation group analysis of the Navier-Stokes equations. The transport equations for turbulence generation and dissipation are the same as those for the standard k-  model, but the model constants differ, and the constant C  1 is replaced by the function C  1RNG.

The RNG k-  Model (Cont.) The transport equation for turbulence dissipation becomes: Where, Where   RNG =0.7179, C  2RNG =1.68,  RNG =0.012, C  RNG =0.085

The k-  Model One of the advantages of the k-  formulation is the near wall treatment for low-Reynolds number computations. The model does not involve the complex non-linear damping functions required for the k-  model and is therefore more accurate and more robust. The k-  models assumes that the turbulence viscosity is linked to the turbulence kinetic energy and turbulent frequency via the relation

The Wilcox k-  Model The starting point of the present formulation is the k-  model developed by Wilcox[1]. It solves two transport equations, one for the turbulent kinetic energy, k, and one for the turbulent frequency, . The stress tensor is computed from the eddy-viscosity concept.

The Wilcox k-  Model (Cont.) k-equation:  -equation: In addition to the independent variables, the density, , and the velocity vector, U, are treated as known quantities from the Navier-Stokes method. P k is the production rate of turbulence, which is calculated as in the k-  model

The Wilcox k-  Model (Cont.) The model constants are given by: The unknown Reynolds stress tensor, , is calculated from:

The Wilcox k-  Model (Cont.) In order to avoid the build-up of turbulent kinetic energy in stagnation regions, a limiter to the production term is introduced into the equations according to Menter [2] : With c lim =10 for  based models. This limiter does not affect the shear layer performance of the model, but has consistently avoided the stagnation point build- up in aerodynamic simulations.

The Baseline (BSL) k-  Model The main problem with the Wilcox model is its well known strong sensitivity to freestream conditions Menter [3]. Depending on the value specified for  at the inlet, a significant variation in the results of the model can be obtained. This is undesirable and in order to solve the problem, a blending between the k-  model near the surface and the k-  model in the outer region was developed by Menter [2].

The Baseline (BSL) k-  Model (Cont.) It consists of a transformation of the k-  model to a k-  formulation and a subsequent addition of the corresponding equations. The Wilcox model is thereby multiplied by a blending function F 1 and the transformed k-  model by a function 1-F 1. F 1 is equal to one near the surface and switches over to zero inside the boundary layer. At the boundary layer edge and outside the boundary layer, the standard k-  model is therefore recovered.

The Baseline (BSL) k-  Model (Cont.) Wilcox model: Transformed k-  model:

The Baseline (BSL) k-  Model (Cont.) Now the equations of the Wilcox model are multiplied by function F 1, the transformed k-  equations by a function 1-F 1 and the corresponding k- and  - equations are added to give the BSL model:

The Baseline (BSL) k-  Model (Cont.) The coefficients of the new model are a linear combination of the corresponding coefficients of the underlying models: coefficients are listed again for completeness:

The Shear Stress Transport (SST) k-  Based Model The k-  based SST model accounts for the transport of the turbulent shear stress and gives highly accurate predictions of the onset and the amount of flow separation under adverse pressure gradients. The BSL model combines the advantages of the Wilcox and the k-ε model, but still fails to properly predict the onset and amount of flow separation from smooth surfaces The main reason is that both models do not account for the transport of the turbulent shear stress.

The Shear Stress Transport (SST) k-  Based Model (Cont.) This results in an over prediction of the eddy-viscosity. The proper transport behavior can be obtained by a limiter to the formulation of the eddy-viscosity: Where

The Shear Stress Transport (SST) k-  Based Model (Cont.) Again F 2 is a blending function similar to F 1, which restricts the limiter to the wall boundary layer, as the underlying assumptions are not correct for free shear flows. S is an invariant measure of the strain rate. The blending functions are critical to the success of the method.

The Shear Stress Transport (SST) k-  Based Model (Cont.) Their formulation is based on the distance to the nearest surface and on the flow variables. With: Where y is the distance to the nearest wall and  is the kinematic viscosity and: With:

The (k-  ) 1E Eddy Viscosity Transport Model A very simple one-equation model has been developed by Menter [4] [5]. It is derived directly from the k-ε model and is therefore named the (k-  ) 1E model: Whereis the kinematic eddy viscosity, turbulent kinematic eddy viscosity and σ is a model constant. is the

The (k-  ) 1E Eddy Viscosity Transport Model (Cont.) The model contains a destruction term, which accounts for the structure of turbulence and is based on the von Karman length scale: Where S is the shear strain rate tensor. The eddy viscosity is computed from:

The (k-  ) 1E Eddy Viscosity Transport Model (Cont.) In order to prevent the a singularity of the formulation as the von Karman length scale goes to zero, the destruction term is reformulated as follows:

The (k-  ) 1E Eddy Viscosity Transport Model (Cont.) The coefficients are:

The (k-  ) 1E Eddy Viscosity Transport Model (Cont.) Low Reynolds Number Formulation Low Reynolds formulation of the model is obtained by including damping functions. Near wall damping functions have been developed to allow integration to the surface: Where D 2 is required to compute the eddy-viscosity which goes into the momentum equations:

Development of maximum deficit velocity in axisymmetric wake mixing length model

Reference ,  [ 1] Wilcox, D.C..“Multiscale model for turbulent flows”.In AIAA 24th Aerospace Sciences Meeting. American Institute of Aeronautics and Astronautics,   [2] Menter, F.R..“Two-equation eddy-viscosity turbulence models for engineering applications”.AIAA-Journal., 32(8),   [3]Menter, F.R., Multiscale model for turbulent flows.In 24th Fluid Dynamics Conference. American Institute of Aeronautics and Astronautics,   [4] Menter, F. R.,“Eddy Viscosity Transport Equations and their Relation to the k-ε Model.”NASA Technical Memorandum , November   [5] Menter, F. R.,“Eddy Viscosity Transport Equations and their Relation to the k-ε Model.”ASME J. Fluids Engineering, vol. 119, pp , 1997.

Thanks For Your Listening …

END