MTF SLIT COMPONENTS Adjusting Blocks and Mounting Plate Steel Blocks

Slides:

Advertisements

Similar presentations

Sectional Assembly and Installation

Advertisements

Pedestrian Gate Electric Strike Maintenance Source location on Dell E510 Computer. C:\Documents and Settings\Michael\My Documents\__F-Xfer\Rentals_Tenants\JASMINE\ARCHITCT\Intercom.

Assembly Instructions DucoSlide Luxframe Controllable TOP BOTTOM L.H. R.H. Control side FRONT SIDE in open position REAR SIDE in open position 1.

MISCELLANEOUS WORKHOLDING FIXTURES

Multi-Sync Repair Training DPM Diversified Products Mfg Inc. Click the Mouse or use the Down Arrow to advance to the next point.

Copyright © Texas Education Agency, All rights reserved. Flexible Manufacturing Precision Machining Safety 1.

Robot Quick Build Session Transmission Assembly Instructions Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team 1750 Special Thanks to.

RockOn! Canister Integration RockOn! 2009.

2006/08/291 DUCOSUN F UniFit FITTING INSTRUCTIONS.

Click on this image to open the full PDF document.

1 FITTING INSTRUCTIONS DUCOSUN UNIFIT Cubic & Linear.

Machining a V-Block Flexible Manufacturing Copyright © Texas Education Agency, All rights reserved. 1.

Motor Leveling MECH 1200 Soft foot Condition: One or more of the mounting feet is not level with the others. Nuts loosen, vibration, misalignment Metal.

Lucas Air Mass Meter Stripdown sequence and technical information.

Advanced Construction Technology

MyLock 644D Service Seminar.

Head jig usage procedure RKC London Office. Set the head jig 2) Put two screws with loose condition 3) Lock the plate 4) Tighten two head jig screws 5)

Solenoid Pressure Regulator Check Valve Hand-turn Valve Pipe Clamp L-Bracket Mounting Block Plastic Tubing AN Fitting AN T-Fitting Pressure Sensor Base.

Inside-, Depth-, and Height-Measuring Instruments

Ledgewood Farm greenhouse construction How do I Start? to I’m Finished!

Unlatch and open the instrument door. Removing the Recorded Tape.

Mitsubishi RA90 4 axis Wire EDM

Hoop Tech Clamp Assembly and Attachment. Contents of package.

Making Coverslips by Steve Smith, Cheng-Zhong Zhang and Amy Xu.

Manufacturing Assembly Plan P Mechanical Spine Test Platform.

LCLS-II Magnetic Structure Design Review - Conceptual Mechanical Design: Module Assembly Method Alan Black Steve Marks 7/6/11 1.

Showing Demonstrations on the TV How to connect the camera to our TV set.

DESIGN AND FABRICATION OF TURNING FIXTURE FOR ELBOW

LAUNCHER BASE PARTS B A D E F C G. LAUNCHER BASE PARTS B A D E F C G.

INDUSTRIAL TECHNOLOGY- METAL ASSOCIATED THEORY TOPIC3. HAND TOOLS & FABRICATION VICESCLAMPSCUTTINGTINSIPS & CHISELS FILESHAMMERSFASTENERSSCREWDRIVERS.

Test & Sewing Samples Copyright © Texas Education Agency, All rights reserved. Images and other multimedia content used with permission.

SQXF Shell & Yoke Assembly Procedure

LINEAR MEASUREMENT.

14.52 in Attach the Axle to the chassis using the four (4) bolts, washers, and nylon lock nuts. Mount the tires. Note: The wheel recess outside on the.

Another "Aha!" puzzle “Blockhead”

Holding Down and Chocking The engine must be securely fixed to the ship. For this the engine is mounted on resin or cast iron chocks and bolted to the.

1 Manufacturing Projects Flexible Manufacturing Copyright © Texas Education Agency, All rights reserved.

1 Polarimeter build up and details Robert Lee. 2 View 1 Material (Removable plate, leg supports and rail guide spacer): Aluminum Leg supports attached.

Side view of generator. Close up of unused grounding pad - gives provisions for mounting the absorber.

Roy Hannaford October 23-24, 2002 RFP Review DFBX Feedbox LEAD SPLICE SPECIFICATION  BY: ROY HANNAFORD.

XR621 Drive Hose Update Kit. Removal Turn off Battery dis Drain hydraulic tank Remove both rubber lines under chassis and discard. Remove and discard.

Simon Calibration Instructions Main Antenna Jig Peter Karlsson V2.

Wayne, The upper and lower guides are now small enough in mass so they can be made directly from the CAD models by stereolithography, and at a reasonable.

BTU … Universal Mounting System Sales Release June 2012.

Rapid Change Technology The following is a presentation to aid Technicians in the replacement of the Rapid Change Technology Block.

WeldingRod’s Exactly Constrained 3D Printer Plate Identification and Stuffing.

Dan Cheng 8/27/2015 MQXFS1 Observations and Feedback from the Assembly Processes, Part II.

# 23 SINGLE IMPLANT CASE Osteotomy Progression in Open Guide Sleeve

What is TETRIX? If you can dream up a robot design, you can build it with the TETRIX Robotics Design System.

GENERAL CAUTION TOOLS REQUIRED ASSEMBLY AND INSTALLATION

Flexible Manufacturing

Unit 26: Mechanical fasteners 1 Dr

Bilge Pump Service Project Model Service Kit

By: Shawn Berkeybile, Dave Martin, Zach Palamara, John Sopczynski

Chapter 26: Mechanical fasteners 1

Horizontal Milling Operations

Stainless Steel Water Well Casing.

Unit 26: Mechanical fasteners 1 Dr

Assembly instructions for M-K all bolt together hoppercone kit.

Mounting a BalanceBox®650 to a brick wall

Chapter 11 Lesson 3 Engine Top End.

McMaster linear bearing #6709K180 with guide rail suppressed

NISSAN Z31 & Z32 OIL PUMP DIFFERENCES

Valve stem “gag” mechanism

2000CIV 2½ ”-10”.

4000CIV 21/2”-10”.

709 2½ ”-10”.

Presentation transcript:

MTF SLIT COMPONENTS Adjusting Blocks and Mounting Plate Steel Blocks Clamps Shims Slide Blocks

Two Blocks of Oil Hardening Steel are separated by shims 100um thick Two Blocks of Oil Hardening Steel are separated by shims 100um thick. This forms the slit for MFT measurements. The blocks are secured via two sets of clamps made from aluminum blocks and stainless steel bolts

The steel blocks need to be adjustable so the slit can be centered under the XRAY beam. To allow adjustment, the bocks have a groove which allow them to move along a ridge on the slide blocks.

The actual adjustment is made by turning the left and right adjusting screws. A dial indicator is mounted on one of the adjusting blocks to determine the amount of movement.

The steel blocks are pulled together with the stainless steel shims separating them by 100 microns. The blocks are clamped loosely at the bottom. Then the sliding blocks are placed in the grooves of the steel blocks. The dial indicator is bolted to one of the adjusting blocks. Adjusting screws are placed in the threaded adjusting blocks. The adjusting blocks are then bolted to the underside of the mounting plate.

The mounting plate ready for assembly. The mounting plate is placed over top of steel blocks.

The top clamps are set in place and tightened.