Wire bundles connecting to Keyence Sensors (screw plug on other end) Colored Wires from bundles (brown, blue, white are nonfunctional, cap with scotch.

Slides:

Advertisements

Similar presentations

#30 Ignition/Starter Switch #54 To Radio Fuse 1 Instrument Power Ignition Coil Red wire with bullet Long black wire with bullet. Wire was.

Advertisements

CricketSat Assembly.

EE188L EE I Laboratory Lab #2 Resistive Circuits.

Introduction To Frc electronics

Most-to-Least Legible Color Combinations for Viewing on Slide Shows Color and contrast are very important tools in communication. They can be used to enhance.

Wiring Color Codes for McLean County 4-H Projects.

What have we learned so far?  When we apply a voltage, the capacitor will charge up to the applied voltage.  The capacitor charges up exponentially.

Digital Camera Integration Presented by: Anna Vigil Electronics Engineering Technology Colorado State University-Pueblo.

Arrange the following in the order of current, starting with the lowest. (A) 7 coulombs in 3 seconds. (B) 10 Volts across 5 Ohms (C) 15 Volts across 7.

60 Hz Variations in Pins Plugged probe into temperature controller output pins: pins 1, 2, 3, 4 all show 1V p-p variations Plugged probe into pins at other.

“Power Supply” Controls Voltage Difference in Voltage is set Output Current is “as requested” by attached device.

Residential Wiring Facts

Using Your Arduino, Breadboard and Multimeter Work in teams of two! living with the lab 1 © 2012 David Hall.

Electrical Wiring Three-Way Switches. Three-Way Switch.

Electricity Wiring Diagrams.

Bob Howard 10/22/2011.  How many connectors do you need ◦ Max DC/Servo Motor Controllers is 4 so use 4  How long should the connectors be ◦

OBJECTIVES 1. Create correctly sized connectivity cabling.

Wiring the Desklamp Basics of Wiring. Types of Wire For this project we will be using two types of wire: 3 wire and standard lamp wire. – 3 wire The wire.

Worksheet Assistance Color Coding Schematics VBloom.

Basic Electricity Facts and Diagrams. Romex Types Determine your need to determine the type of Romex needed Gage Size of the wire (common = 12 or 14)

RM2C Understanding Connections on the Robot Control Board (RCB).

Write a program that will automatically control the brightness of a light based on the surrounding light level. Automatic Night Light.

Electrical Power Distribution in America % Coal 20.4% Nuclear 20.3% Natural Gas 6% Hydro Electric 3.4% Other

Title: Corvette C5 Column Lock Bypass Originator: John Neese Date: 30 Jan 2005 Revision: Sheet: 1 of 6 Column Lock Bypass.

1 LIGO-G V1 Magnetometer DC Power Assessment Magnetometers are distributed in the corner station and both end stations. The complete chain of one.

12. Power Distribution Systems 1) Schematic diagram of part of a house wiring system 1.

Setting up the Ricoh C305 Press F5 to start the Presentation

Using a Multimeter McTigue Junior High Technology Ed. Click Here

How to Make ECG Leads Strip 2-3” of insulation

Installation Guide for AC-1000RF & SA V1.6 Installation Guide for AC-1000RF & SA V1.6 Version Eng1.10 Jul., Union Community Co., Ltd.

ELECTRONICS AND SAFETY Scarlett, Dash, Sam, Ashley, and Eric.

Wiring –Basic light switch

Kids S1 Vocabulary U1 Colors. Listen and say the color:

Basic Electricity Facts and Diagrams. Cable Types Determine your need to determine the type of cable (Romex) needed Gage Size of the wire (common = 12.

If you say 8 color the ones in your picture purple. If you say 9 color the ones in your picture blue.

Monkey, Monkey In the Tree. Monkey, monkey in the tree Throw the yellow coconut down to me!

Basic Equipment and Schematic Reading. Objectives Learn the basic equipment that will be used in the Lab. Learn some of the basic symbols used on electrical.

Designing a Next-Generation Surgical Robot Activity.

 Nonmetallic sheathed cable: copper or aluminum wire covered with paper, rubber, or vinyl for insulation  Armored cable: flexible metal sheath with.

Earth Layers Foldable Follow each of the steps carefully in this presentation to complete your foldable.

 A multimeter is tool that measures electrical currents. It is a combination of many different measurements in one tool.

ETHERNET CABLE TYLER THORNBURG LTEC STRIPPING AND CUTTING First you will need to strip the wire. I used scissors to cut off the rubber around.

Building Circuits.

Wiring For MAF Conversion on Mitsubishi 3000 GT ‘91-’93 Non OBDII

Tether Management.

Watch Pete the Cat here:

Schematic diagram of part of a house wiring system

Three-Phase Power.

1) Schematic diagram of part of a house wiring system

Colors/Color Words.

Digital Multimeter (DMM)

My Penguin Math Book By:

SW REV Position, DIFFERENCES ONLY SHOWN, L1 is the same

FIGURE 21-1 The digital multimeter should be set to read DC volts, with the red lead connected to the positive (+) battery terminal and the black meter.

Electrical Wiring Single Pole Switches.

NI Data Acquisition (DAQ) Wiring and Connections

Fundamentals of Electrical Circuits

Wiring the Light and Relay

ALL these are “INS” (tied together w/ DRUM SW)

Removes these two screws that attach the Controller to the Hopper Box.

Can I color yellow?. Can I color yellow?

Colors/Color Words.

What Color is it?.

Which of the following would best describe the situation inside the circle?

Directions: Fill in the blanks with the correct answers then color in the picture with the given color. Color White: A full rotation around a.

Replacing TrueAir Thermostat with Ecobee SI

Presentation transcript:

Wire bundles connecting to Keyence Sensors (screw plug on other end) Colored Wires from bundles (brown, blue, white are nonfunctional, cap with scotch locks) BLACK wire (data) from each bundle (sensor) is screwed into each channel (0-7) Blue (ground) screwed into channel 9 on each DAQ Blue wires are coupled with the BLUE wire from sensor 1 (the control sensor, you should have one sensor with a different label) These are all screwed into the white pots and connect to the ground from your AC to DC power supply (see next slide)

Brown wire from control sensor screwed in pot with RED (hot) wire from power supply out other end Blue wire (ground) from control and channel 9 of each DAQ screwed in pot with BLACK (ground) from power supply screwed into the other end Connector for Power Supply (other ends soldered to power supply

Need 12V power supply that can output AT LEAST 1 AMP Cut and Resolder wires coming from POWER SUPPLY, make sure hot and ground are correctly distinguished!!! Use a multimeter to figure this out. In the pic below the wire with the orange tape (white dashes is hot) and the black wire is ground.