Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion I plan on indicating for each lecture(s) of this year the equivalent lecture(s) from.

Slides:



Advertisements
Similar presentations
1 Series Resonant Converter with Series-Parallel Transformers for High Input Voltage Applications C-H Chien 1,B-R Lin 2,and Y-H Wang 1 1 Institute of Microelectronics,
Advertisements

ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 19 State plane trajectory of a parallel-loaded tank circuit.
Quasi-square-wave ZVS converters
Chapter 20 Quasi-Resonant Converters
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 37 Active clamp circuits Can be viewed as a lossless voltage-clamp snubber.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lectures The conventional forward converter Max v ds = 2V g + ringing Limited.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 37 Zero-voltage transition converters The phase-shifted full bridge converter.
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion 19.4 Load-dependent properties of resonant converters Resonant inverter design objectives:
Fundamentals of Power Electronics 1 Chapter 20: Quasi-Resonant Converters 20.2 Resonant switch topologies Basic ZCS switch cell: SPST switch SW : Voltage-bidirectional.
1 Parameters for various resonant switch networks.
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion Reduction of power converter size through increase of switching frequency Increasing.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 37 Soft-switching converters with constant switching frequency With two.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lectures Zero-voltage transition converters The phase-shifted full bridge.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 37 Zero-voltage transition converters The phase-shifted full bridge converter.
1 Quasi-square-wave ZVS converters A quasi-square-wave ZVS buck Resonant transitions but transistor and diode conduction intervals are similar to PWM Tank.
Chapter 20 Quasi-Resonant Converters
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion 19.4 Load-dependent properties of resonant converters Resonant inverter design objectives:
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 23 General Solution for the Steady-State Characteristics of the Series.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 37 Zero-voltage transition converters The phase-shifted full bridge converter.
Soft-switching converters with constant switching frequency
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion 19.4 Load-dependent properties of resonant converters Resonant inverter design objectives:
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 36 Midterm Exam Averages: all students 78.1 on-campus students 78.3 off-campus.
Fundamentals of Power Electronics 1 Chapter 20: Quasi-Resonant Converters Chapter 20 Quasi-Resonant Converters Introduction 20.1The zero-current-switching.
Parallel resonant dc-dc converter
ECD 442 Power Electronics1 Power MOSFETs Two Types –Depletion Type Channel region is already diffused between the Drain and Source Deplete, or “pinch-off”
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion Operation of the full bridge below resonance: Zero-current switching Series.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 37 Zero-voltage transition converters The phase-shifted full bridge converter.
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion Chapter 19 Resonant Conversion Introduction 19.1Sinusoidal analysis of resonant converters.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 23 Series resonant converter.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 23 Operating Modes of the Series Resonant Converter Lecture 23 Resonant.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 23 Steady state solution of state plane Two possible trajectories for given.
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion Announcements Homework #2 due today for on-campus students. Off-campus students submit.
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion Upcoming Assignments Preparation for Lecture 2: Read Section 19.1, Sinusoidal analysis.
Fundamentals of Power Electronics 1 Chapter 20: Quasi-Resonant Converters Chapter 20 Quasi-Resonant Converters Introduction 20.1The zero-current-switching.
Transistors in Parallel. Why connect transistors in parallel? Connect in parallel to handle high currents Need to be closely matched for equal current.
Power Electronics Chapter 8 Soft-Switching Techniques.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 23 Announcements Correction to HW #2, Problem 19.3 solution Clarification.
Chapter 20 Quasi-Resonant Converters
Fundamentals of Power Electronics 1 Chapter 20: Quasi-Resonant Converters Chapter 20 Quasi-Resonant Converters Introduction 20.1The zero-current-switching.
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion For both on-campus and CAETE students: A DVD of recorded lectures from Professor Erickson’s.
Resonant and Soft-Switching Techniques in Power Electronics ECEN 5817
Waveforms of the half-wave ZCS quasi-resonant switch cell
Buck-derived full-bridge converter
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 26 Discontinuous conduction mode (DCVM) Occurs at heavy load and low output.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 19 Time-Domain Analysis of Resonant and Soft-Switching Converters Principles.
Zero-Voltage or Zero-Current Switchings
LECTURE 9 INTRO TO POWER ELECTRONICS
1 © Alexis Kwasinski, 2012 Power electronic interfaces Power electronic converters provide the necessary adaptation functions to integrate all different.
1 Fly-back Converter fall Basic Topology of a Fly-back Converter.
WEEK 7 DC SWITCHING POWER SUPPLIES, PART II 1. EXPECTATIONS Describe the supply isolation characteristics afforded by transformers. Draw basic forward,
Electronic Troubleshooting
Power Electronics and Drives (Version ) Dr. Zainal Salam, UTM-JB 1 Chapter 3 DC to DC CONVERTER (CHOPPER) General Buck converter Boost converter.
Soft-Switching DC-DC Converter Is to shape the voltage or the current waveform by creating a resonant condition to: Force the voltage across the switching.
Zero Voltage Switching Quasi-resonant Converters
Chapter 6 Soft-Switching dc-dc Converters Outlines
A Unified Model for the ZVS DC-DC Converters With Active Clamp
Chapter 5 DC to AC Converters Outline 5.1 Commutation 5.2 Voltage source inverters 5.3 Current source inverters 5.4 Multiple- inverter connections and.
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion Solution of converter voltage conversion ratio M = V/V g Eliminate R e :
PARISUTHAM INSTITUTE OF TECHNOLOGY AND SCIENCE
19.4 Load-dependent properties of resonant converters
Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion 19.3 Soft switching Soft switching can mitigate some of the mechanisms of switching.
ECEN 5817 Resonant and Soft-Switching Techniques in Power Electronics 1 Lecture 19 Time-Domain Analysis of Resonant and Soft-Switching Converters Principles.
Zero-current Switching Quasi-resonant Converters
POWER ELECTRONICS & ITS APPLICATION
IMPEDENCE - SOURCE INVERTER FOR MOTOR DRIVES
DC-DC PWM Converters Lecture Note 5.
Buck-derived full-bridge converter
Resonant and Soft-Switching Techniques in Power Electronics ECEN 5817
ECEN 5817 Housekeeping update
ECEN 5817 Housekeeping I plan on indicating for each lecture(s) of this year the equivalent lecture(s) from Spr. 06. This will make it easy if you choose.
Presentation transcript:

Fundamentals of Power Electronics 1 Chapter 19: Resonant Conversion I plan on indicating for each lecture(s) of this year the equivalent lecture(s) from Spr. 06. This will make it easy if you choose to watch those lectures to stay in synch with this years class if we should run at a slightly different pace. I will also indicate if there is any new material for this year not covered in Spr. 06 so you will know to watch / attend that particular lecture this year. Similarly, any material covered in Spr. 06 but not covered this year will not show up as an equivalent lecture so you will know you can skip it. Today (lecture 4) we will cover material covered in lecture 7 of the Spr. 06 class. You may wish to watch some of Spring 06 lectures 1 to 3 for some valuable insight and historical perspective on resonant power conversion techniques. ECEN 5817 Housekeeping

Fundamentals of Power Electronics 2 Chapter 19: Resonant Conversion 2 different ways to construct transfer function H

Fundamentals of Power Electronics 3 Chapter 19: Resonant Conversion Dc conversion ratio of the PRC At resonance, this becomes PRC can step up the voltage, provided R > R 0 PRC can produce M approaching infinity, provided output current is limited to value less than V g / R 0

Fundamentals of Power Electronics 4 Chapter 19: Resonant Conversion Model: series resonant converter

Fundamentals of Power Electronics 5 Chapter 19: Resonant Conversion Comparison of approximate and exact characteristics Series resonant converter Below resonance: 0.5 < F < 1 Above resonance: 1 < F

Fundamentals of Power Electronics 6 Chapter 19: Resonant Conversion Comparison of approximate and exact characteristics Parallel resonant converter Exact equation: solid lines Sinusoidal approximation: shaded lines

Fundamentals of Power Electronics 7 Chapter 19: Resonant Conversion Chapter 19 Resonant Conversion Introduction 19.1Sinusoidal analysis of resonant converters 19.2Examples Series resonant converter Parallel resonant converter 19.3Soft switching Zero current switching Zero voltage switching 19.4Load-dependent properties of resonant converters 19.5 Exact characteristics of the series and parallel resonant converters

Fundamentals of Power Electronics 8 Chapter 19: Resonant Conversion 19.3 Soft switching Soft switching can mitigate some of the mechanisms of switching loss and possibly reduce the generation of EMI Losses due to high voltage and high current present in switch during transitions, Losses due to shorting device capacitances Semiconductor devices are switched on or off at the zero crossing of their voltage or current waveforms: Zero-current switching: transistor turn-off transition occurs at zero current. Zero-current switching eliminates the switching loss caused by IGBT current tailing and by stray inductances. It can also be used to commutate SCR’s. Zero-voltage switching: transistor turn-on transition occurs at zero voltage. Diodes may also operate with zero-voltage switching. Zero-voltage switching eliminates the switching loss induced by diode stored charge and device output capacitances. Zero-voltage switching is usually preferred in modern converters, including soft-switching PWM converters.

Fundamentals of Power Electronics 9 Chapter 19: Resonant Conversion Operation of the full bridge below resonance: Zero-current switching Series resonant converter example Current bi-directional switches ZCS vs. ZVS depends on tank current zero crossings with respect to transistor switching times = tank voltage zero crossings Operation below resonance: input tank current leads voltage Zero-current switching (ZCS) occurs

Fundamentals of Power Electronics 10 Chapter 19: Resonant Conversion Tank input impedance Operation below resonance: tank input impedance Z i is dominated by tank capacitor.  Z i is negative, and tank input current leads tank input voltage. Zero crossing of the tank input current waveform i s (t) occurs before the zero crossing of the voltage v s (t) – before switch transitions

Fundamentals of Power Electronics 11 Chapter 19: Resonant Conversion Switch network waveforms, below resonance Zero-current switching Conduction sequence: Q 1 –D 1 –Q 2 –D 2 Tank current is negative at the end of each half interval – antiparallel diodes conduct after their respective switches Q1 is turned off during D1 conduction interval, without loss

Fundamentals of Power Electronics 12 Chapter 19: Resonant Conversion Classical but misleading example: Transistor switching with clamped inductive load (4.3.1) Buck converter example transistor turn-off transition Loss:

Fundamentals of Power Electronics 13 Chapter 19: Resonant Conversion Switch network waveforms, below resonance Zero-current switching Conduction sequence: Q 1 –D 1 –Q 2 –D 2 Q 1 is turned off during D 1 conduction interval, without loss Note on terminology:

Fundamentals of Power Electronics 14 Chapter 19: Resonant Conversion ZCS turn-on transition: hard switching Q 1 turns on while D 2 is conducting. Stored charge of D 2 and of semiconductor output capacitances must be removed. Transistor turn-on transition is identical to hard- switched PWM, and switching loss occurs.

Fundamentals of Power Electronics 15 Chapter 19: Resonant Conversion

Fundamentals of Power Electronics 16 Chapter 19: Resonant Conversion More on diode reverse recovery Circuits with diode and switch in loop – when turn on switch diode turns off (unless ZVS)

Fundamentals of Power Electronics 17 Chapter 19: Resonant Conversion More on diode reverse recovery In steady-state: Diode equations : Stored minority charge profile under forward-biased conditions

Fundamentals of Power Electronics 18 Chapter 19: Resonant Conversion Induced losses Stored charge is exponential function of voltage - require large change in q to get small change in v D v D remains > 0 until all stored charge removed – holding voltage across MOSFET = V g while MOSFET is providing not only i L, but diode reverse current as well. Induces losses in MOSFET This energy loss is MUCH greater than the energy stored in diode in the form of stored charge as well as across depletion capacitance

Fundamentals of Power Electronics 19 Chapter 19: Resonant Conversion Operation of the full bridge above resonance: Zero-voltage switching Series resonant converter example Operation above resonance: input tank current lags voltage Zero-voltage switching (ZVS) occurs

Fundamentals of Power Electronics 20 Chapter 19: Resonant Conversion Tank input impedance Operation above resonance: tank input impedance Z i is dominated by tank inductor.  Z i is positive, and tank input current lags tank input voltage. Zero crossing of the tank input current waveform i s (t) occurs after the zero crossing of the voltage v s (t) – after switch transitions

Fundamentals of Power Electronics 21 Chapter 19: Resonant Conversion Switch network waveforms, above resonance Zero-voltage switching Conduction sequence: D 1 –Q 1 –D 2 –Q 2 Tank current is negative at the beginning of each half-interval – antiparallel diodes conduct before their respective switches Q 1 is turned on during D 1 conduction interval, without loss – D 2 already off!

Fundamentals of Power Electronics 22 Chapter 19: Resonant Conversion ZVS turn-off transition: hard switching? When Q 1 turns off, D 2 must begin conducting. Voltage across Q 1 must increase to V g. Transistor turn-off transition is identical to hard-switched PWM. Switching loss may occur… but….

Fundamentals of Power Electronics 23 Chapter 19: Resonant Conversion Classical but misleading example: Transistor switching with clamped inductive load (4.3.1) Buck converter example transistor turn-off transition Loss:

Fundamentals of Power Electronics 24 Chapter 19: Resonant Conversion Soft switching at the ZVS turn-off transition Introduce small capacitors C leg across each device (or use device output capacitances). Introduce delay between turn-off of Q 1 and turn-on of Q 2. Tank current i s (t) charges and discharges C leg. Turn-off transition becomes lossless. During commutation interval, no devices conduct. So zero-voltage switching exhibits low switching loss: losses due to diode stored charge and device output capacitances are eliminated.

Fundamentals of Power Electronics 25 Chapter 19: Resonant Conversion 19.4 Load-dependent properties of resonant converters Resonant inverter design objectives: 1. Operate with a specified load characteristic and range of operating points With a nonlinear load, must properly match inverter output characteristic to load characteristic 2. Obtain zero-voltage switching or zero-current switching Preferably, obtain these properties at all loads Could allow ZVS property to be lost at light load, if necessary 3. Minimize transistor currents and conduction losses To obtain good efficiency at light load, the transistor current should scale proportionally to load current (in resonant converters, it often doesn’t!)