Anatomy of a Cabinet. Pick a cabinet now! A) A freestanding display space B) A counter section no longer than 48” (you may “cut” a counter to do this)

Slides:

Advertisements

Similar presentations

Microsoft ® Word 2010 Training Create your first Word document II.

Advertisements

**** ORDER OF OPERATIONS ****. STEP 1: VERTICAL Style Fold (Leave a little space at the bottom showing)

Objective: Develop plans for kitchen cabinets.

Drafting – Product Design & Architecture

Drawing furniture using One Point Perspective

1 1 Change Margins 2 Change Paper Size 3 Insert Breaks 4 Hyphenation and Nonbreaking space 5 Control Pagination Students will be able to do the following.

1 Helpful Notes 2005 Tutorial 1 : Game Pad.

Wall N Pond C17 (surface) Outlet 2”Cast Pipe **surface measurements only – see additional graphics for bottom and depth of pond. Height of door is 5’10”.

Competency: Design and draw interior elevations for kitchens and baths Objective: Explain the elements of kitchen and bath design.

Marshall x10” Combo: Front View Logo Mounting: -Centered and 1-7/8” up from piping (not sure if this is factory placement or not) 14.5” Rubber feet:

Isometric and Oblique Pictorials

 Divide your paper horizontally at one third from the top and mark two vanishing points at each end of the line.

Microsoft ® Word 2010 Training Create your first Word document II.

SURFACE AREA and VOLUME of RECTANGULAR PRISMS and CUBES.

Orthographic Projection Basics

 Next - Previous  Horizontal Bar  Vertical Menu.

7.2 Areas Between Curves. Area Region R is bounded by the curves y = 2 – x 2 and y = -x. Sketch region R. R What is the area of region R?

Graphic Language of Buildings Architectural Plans.

PLANOMETRIC VIEW OF A KITCHEN.

Engineering Drawing and Design Chapter 15 Pictorial Drawings

Slant Heights of Pyramids and Cones LESSON 95. Slant Height The slant height is the distance from the base to the apex along the outside of the surface.

Internal usage only 0 CD Key Points: The Logo with Pyramid  The logo with pyramid exists in two versions from top down and from bottom up  The logo is.

APPLICATIONS OF TECHNOLOGY

If I wanted to walk around the yellow area, how far would you need to walk?

Traditional Furniture Locks 1 J. Byrne Locks Small finely made locks are fitted to furniture and boxes. However, they do not provide total security,

Area Volume Measures a given space Length and Width 2-D 3-D Length times width L x W Length times width time height L x W x H Measures the space of a flat.

CPA Micarta Based Rahul Sharma / Bill Sands. The present design shown in this document is based on the use of Micarta as the base material this will likely.

Two-Point Perspective Sketching

Freehand Sketching. Draw a horizontal line about 70 mm long, and then another six lines underneath, each separated by about 10 mm.

SANTANA DRAFTING MULTIVIEWS 1 An introduction Mr. Fitzgerald Rm

Math B Project Surface Area and Volume of 3D Prisms with Nets By Kyle Garcia.

7.2 Areas in the Plane. How can we find the area between these two curves?

Chapter 11: Surface Area & Volume

polyhedron a three- dimensional figure whose surfaces are polygons faces edge vertex.

Multiply By 2-Digit Numbers (B) Unit 2 Lesson 6. Objectives:

Areas in the Plane Gateway Arch, St. Louis, Missouri Greg Kelly, Hanford High School, Richland, WashingtonPhoto by Vickie Kelly, 2003.

11.2: Graphing Rational Functions Algebra 1: May 1, 2015.

Section 2.6 Rational Functions Part 2

The Language of Anatomy

Welding Symbols Developed by the American Welding Society in the 1930’s. Welding symbol refers to the total symbol including all information added to specify.

MULTIVIEWS 1 An introduction

Section 5.1 Area Between Curves.

Traditional Furniture Locks

Orthographic Projection

Orthographic Projection

Fold a piece of computer paper in half, hamburger style

Engineering drawing Every language has its own rules of grammar.

Alternate Views Introduction to Engineering Design

Layer Thickness and Map Width

Solidworks Computer-Aided Drafting Program LESSON 5-BOB

Notes 7-2 The Coordinate Plane.

Elasticity Examples.

Graphing More Complex Rational Functions

Cutting Pumpkins Donuts Work Too! 12/9/2018.

Elements and Principle Foldable Instructions

Multiplication Grids.

Graphs of Rational Functions

Wall and Ceiling Construction

Similar Right Triangles

How to Draw The Human Face

Objective: Develop plans for kitchen cabinets.

Objective: Explain the elements of kitchen and bath design.

Miniature Train Wheels.

Cross Sections.

Graphing Horizontal and

Miniature Train Project

Fig. 2 CFD results. CFD results. Results of CFD simulations in horizontal (left column) and vertical (right column) cross-sections. All models oriented.

Extending your knowledge Circumference of a circle =

Presentation transcript:

Anatomy of a Cabinet

Pick a cabinet now! A) A freestanding display space B) A counter section no longer than 48” (you may “cut” a counter to do this)

How to start... Sketch the cabinet What’s inside? What’s on top? Dimension it List the materials

BOTTOM TOP MIDDLE

3 Types of Bases: Recessed Flush Surface mount Typical toespace is 3” to 6”, both vertical and horizontal.

Middle

Top

Multiple work surfaces

Your cabinet should be no more than 48” long. Switching to ACAD...