Experimental techniques Linear-sweep voltammetry At low potential value, the cathodic current is due to the migration of ions in the solution. The cathodic current grows as the potential reaches the reduction potential of the reducible species. Based on the eqn. j lim = zFDc/ δ, the maximum current is proportional to the molar concentration of the species. This is why one can determine c from this technique

Differential pulse voltammetry The current is monitored before and after a pulse of potential is applied. The output is the slope of a curve like that obtained by linear-sweep voltammetry

Cyclic voltammetry Determine the redox potential Reflect the underlying kinetics

CV spectrum, the sweeping rate and the underlying kinetics

Self-test 25.9 Suggest an interpretation of the cyclic voltammogram shown in the figure. The electroactive material is ClC 6 H 4 CN in acidic solution; after reduction to ClC 6 H 4 CN -1, the radical anion may form C6H5CN irreversibly. ClC 6 H 4 CN + e ↔ ClC 6 H 4 CN -1 ClC 6 H 4 CN -1 + H + + e → C 6 H 5 CN + Cl - C 6 H 5 CN + e ↔ C 6 H 5 CN -

25.11 Electrolysis Cell overpotential: the sum of the overpotentials at the two electrodes and the ohmic drop due to the current through the electrolyte (IR s ). Electrolysis: To induce current to flow through an electrochemical cell and force a non-spontaneous cell reaction to occur. It requires that the applied potential difference exceed the zero-current potential by at least the cell overpotential. Estimating the relative rates of electrolysis.

Working galvanic cells In working galvanic cells, the overpotential leads to a smaller potential than under zero-current conditions. The cell potential decreases as current is generated because it is then no longer working reversibly. Consider the cell M|M + (aq)||M’ + (aq)|M’ and ignore complications from liquid junctions. The potential of the cell E’ = ΔФ R - ΔФ L As ΔФ R = E R + η R ; ΔФ L = E L + η L E’ = E + η R - η L

To emphasize that a working cell has a lower potential than a zero- current cell, we write E’ = E - |η R |- |η L | One should also subtract the ohmic potential difference IRs E’ = E - |η R |- |η L | - IRs The omhic term is a contribution to the cell’s irreversibility- it is a thermal dissipation. E’ = E – IRs – 4RT ln(I/9Aj))/F j = (j oL j oR ) 1/2 where j oL and j oR are the exchange current densities for the two electrodes (for single electron transfer and high overpotential) The concentration overpotential also reduces the cell potential see (8 th edition) or )7 th edition) The full expression for the cell potential when a current I is being drawn: see eqn a or 29.60

The dependence of the potential of a working cell on the current density being drawn (blue line) and the corresponding power output (IE)

Fuel Cells Reactants are supplied from outside. In hydrogen/oxygen cell, the electrolyte used is concentrated aqueous potassium hydroxide maintained at 200 o C and atm. The cathode reaction is O 2 (g) + 2H 2 O(l) + 4e - → 4OH - (aq) Eo = 0.40V The anode reaction is oxidation H 2 (g) + 2OH - (aq) → 2H 2 O(l) + 2e - The overall reaction 2H 2 (g) + O 2 (g) → 2H 2 O(l) E = 1.23V The advantage of the hydrogen/oxygen system is the large exchange current density of the hydrogen reaction, but the oxygen reaction has a small exchange current density.

25.13 Corrosion

Consider the following half reactions: In acidic environment: (a) 2H + (aq) + 2e → H 2 (g) E o = 0 (b) 4H + (aq) + O 2 + 4e → 2H 2 O(l) E o = 1.23 V In basic solution: (c) 2H 2 O(l) + O 2 (g) + 4e → 4OH - (aq) E o = 0.40 V Consider the other half reaction: Fe 2+ (aq) + 2e → Fe(s) E o = -0.44V The potential difference suggests that iron can be oxidized under the above three conditions. The thermodynamic discussion only indicates the tendency. The kinetic process shall also be examined.

Self-test: The exchange current density of a Pt(s)|H 2 (g)|H + (aq) electrode at 298K is 0.79 mAcm -2. Calculate the current density when the over potential is +5.0mV. What would be the current at pH = 2.0, the other conditions being the same? Solution: Step1: using Nernst equation to calculate E, Step 2: calculate η on the basis that there is no change in E’; η = E’ – E: step 3: J = j 0 fη

25.23b Suppose that the electrode potential is set at 0.50 V. calculate the current density for the ratio of activities α(Cr 3+ )/α(Cr 2+ ) in the range 0.1 to 10.0 and at 25 o C.