Parameters monitored by Quick 1.Vibration (5 Hz) Up to 4 vibration channels usually configured to monitor the same vibration transducer at different frequency.

Slides:



Advertisements
Similar presentations
Bendix Fuel Control System Theory of Operation
Advertisements

JET ENGINE MECHANICAL ARRANGEMENT
INDUSTRIAL TRAINING BHEL –EDN BANGLORE SARATH T.S M110278EE.
JET PROPULSION Part 3 The Jet Engine.
LESSON TEN. AIR AND EXHAUST SYSTEMS AND TURBOCHARGERS.
SCADA-Based Condition Monitoring Joining advanced analytic techniques with turbine engineering Michael Wilkinson EWEA 2013, Vienna.
JET PROPULSION Part 1 The Compressor.
© A. Kwasinski, 2014 ECE 2795 Microgrid Concepts and Distributed Generation Technologies Spring 2015 Week #3.
Internal Combustion Engines. Engines External combustion engine Internal combustion engine Steam engine Gas turbine engine Steam engine Gas turbine engine.
3-Multi - Can Annular Combustor 3-Multi - Can-Annular Combustor The third design and the one preferred by most manufacturers, is the can-annular combustor,
Turbochargers ure=related.
FUNCTIONS OF THE GOVERNING SYSTEM
Mechanical Aspiration The process of mechanically increasing the manifold pressure of an engine in order to maintain and/or increase horsepower. Ambient.
Experiment #4 IC Engine.
Sensors used in EFI (Electronic Fuel Injection)
How do aircraft jet engines work?
Gas Turbines By: Katie Steddenbenz.
Large Steam& Gas Turbines P M V Subbarao Professor Mechanical Engineering Department Backbones of Modern Nations ……
Air Compressors.
TURBOCHARGERS & SUPERCHARGERS
Electronic control gasoline injection system—Sensor
1 GENERATION TECHNOLOGIES -- Bhanu Bhushan -- (April, 2011)
Analysis of Turbofan Engine
Operation and Maintenance
MAE 4261: AIR-BREATHING ENGINES Exam 2 Review Exam 2: November 18 th, 2008 Mechanical and Aerospace Engineering Department Florida Institute of Technology.
Inner bearing Outer & Thrust bearing TWO GASTURBINES DRIVING PROCESS COMPRESSOR Compre ssor EQUIPMENT TRAIN ARRNAGEMENT.
Gas Turbine Theory and Construction
Slide # 1 Velocity sensor Specifications for electromagnetic velocity sensor Velocity sensors can utilize the same principles of displacement sensor, and.
Motor Testing (Motor Only)
Design and Testing of a Unique Compressor Test Facility Jörgen Olsson
FUNDAMENTALS OF GAS TURBINE CONTROL
Copyright 2002AST Training A.S.T. Training’s Introduction to Driver’s Seat Diagnostics.
® AutoTune ™. ® Always optimal engine setting Higher productivity – Optimal engine performance at all times – No time spent on carburettor adjustments.
(C) 2006, SUCCESS by DESIGN Surge Values at Each Test Stator surged to fault Indicates decrease in dielectric strength following each test. Applied Surge.
Turbocharger matching While the operating engineer will not normally be involved in turbo-charger matching, a familiarity with the procedure will lead.
1 GENERATION TECHNOLOGIES -- Bhanu Bhushan -- (April, 2011)
CONTROL BOX RMG
Engine Management Systems and Calibration
Input Sensors/Fuel injection
T700 ENGINE.
SCT INSTITUTE OFTECHNOLOGY
Instructor Click a Section Tab
WORK Work = Force x Distance POWER power = work done ÷ time taken ENERGY 1-POTENTIAL ENERGY (Potential Energy = Force x Distance ) 2-KINETIC ENERGY Energy.
T700 System Overview UH-60 IPC CW4 Jim Hill.
Advantages of Rotating Machines Less balancing problems Low lubricating oil consumption Higher reliability.
Types of Sensors Used in Multi-Point Fuel Injection System
1 TRANSDUCER. 2 Contents To understand the basic concept of Transducer To learn about Block diagram of transducer Different Applications of transducers.
250-C20J Engine System.
Transducers Topics covered in this presentation:
Variable Geometry Turbocharger
Prepared by: Kamil Bin Sahidin
INTRODUCTION TO ELECTRONIC INSTRUMENTATION
MULTI POINT FUEL INJECTION
Control System Instrumentation
Engineering Technology Division
Transducers Topics covered in this presentation:
SUPERCHARGING AND TURBOCHARGING
Mechanical Aspiration
Electric Machine Induction Motor
Engine Control Systems
Induction Generators Same basic construction as squirrel-cage induction motors Drive at a speed greater than the synchronous speed Not started as a motor.
Content Development of the second generation Power2 Case studies
MicroLogix Packaged Controllers
Variable Geometry Turbocharger
CONTROL BOX RMG
Unit 6 Turbine Vibration Investigation - Observation by PMT
Sensors Chapter 17 Lesson 3.
Design of Steam & Gas Turbines
Issues in Mechanical Diagnostics of Jet Engines
Presentation transcript:

Parameters monitored by Quick 1.Vibration (5 Hz) Up to 4 vibration channels usually configured to monitor the same vibration transducer at different frequency ranges (500, 1250Hz, 2.5, 5, 10, 40, 80 kHz).Up to 4 vibration channels usually configured to monitor the same vibration transducer at different frequency ranges (500, 1250Hz, 2.5, 5, 10, 40, 80 kHz). The 3 shaft speeds and a once-per-rev tachometer signal to give phase.The 3 shaft speeds and a once-per-rev tachometer signal to give phase.

Parameters monitored by Quick 1.Performance Parameters (20-40Hz) Flight condition : Altitude, Mach number Fuel : Fuel Metering Valve position, Demanded Fuel flow, Fuel flow meter Outputs : Exhaust Pressure ratio, shaft speeds, Turbine gas temp. Oil System : Oil Pressure, temperature, quantity Control system : Demanded Bleed valve positions, Variable stator vane position, Control loop flag, Throttle angle Fault detection : Magnetic Chip detector, Surge detect Temperatures & Pressures : Ambient (20), IP (25), HP (30), By-pass Pressure (16), Exhaust Pressure, Turbine Air temp Others

Features, Symptoms & Events 1.Features Occurrences of diagnostic interest. E.g. step change in vibration levelOccurrences of diagnostic interest. E.g. step change in vibration level

Features, Symptoms & Events 1.Features Occurrences of diagnostic interest. E.g. step change in vibration levelOccurrences of diagnostic interest. E.g. step change in vibration level 2.Symptoms A feature occurring at a specific engine condition may be a symptom of a known fault.A feature occurring at a specific engine condition may be a symptom of a known fault.

Features, Symptoms & Events 3.Events The co-occurrence of several symptoms leads to the diagnosis of an eventThe co-occurrence of several symptoms leads to the diagnosis of an event

Features – Symptoms - Diagnosis Diagnosis number 11 Diagnosis 1 "Bowed Rotor Start" HP_SHAFT Diagnosis 2 "Bird Strike" LP_COMP Diagnosis 3 "IP Lockplate" IP_COMP Diagnosis 4 "LP Out of Balance" LP_COMP Diagnosis 5 "IP Out of Balance" IP_SHAFT Diagnosis 6 "HP Out of Balance" HP_SHAFT Diagnosis 7 "LP Mass redistribution" LP_COMP Diagnosis 8 "IP Mass redistribution" IP_COMP Diagnosis 9 "IP Failure" IP_COMP Diagnosis 10 "HP Mass redistribution" HP_COMP Diagnosis 11 "Radial Drive Shaft bearing" HP_SHAFT List of known events defined in a config file :

Features – Symptoms - Diagnosis Symptom 1 of diagnosis 1 ; step_change 1h condition ACCEL STARTUP ; Symptom 2 of diagnosis 1 ; climit_detector 1h condition ACCEL STARTUP ; List of Symptoms per fault :