March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 1 Working drawings of an Assembly Complete each drawing fully before proceeding on to the next one.

Slides:

Advertisements

Similar presentations

Section 1 – Manual Graphics

Advertisements

Packaging Design: Net This net is for an octagonal based prism. As with all technical drawings, the equipment goes a long way in helping you to draw a.

1.Must be completed prior to the end of your first term in ROTC. 2.The Form 48 is a “road map” that outlines ALL your academic classes until graduation.

1 5. Creating Sectioncal Views This week you will learn creating sectional views. The steps to follow are: Cutting Plane Types of sectional views (full,

Chapter 5 Creating and Editing Drawing Views. After completing this chapter, you will be able to – Understand drawing options – Create and edit drawing.

Chapter 20 Working Drawings

SDC PUBLICATIONS © 2011 Chapter 11 Assembly Drawings and Blocks Learning Objectives:  Create an Assembly Drawing from Part files.  Using AutoCAD with.

Orthographic Projection

Fill in these particulars. Full name of CentreCentre Number ST. AIDAN’S HIGH SCHOOL Site (where appropriate) Forename(s)Surname Date of BirthScottish.

Using the Drafting Workbench R. Lindeke IE Before Entering the Drafting WB Create the Part in Handout: I used a Master Sketch For the Base 2’ary.

Introduction to the French Revolution. Agenda 1.Recap –French Revolution 2.Vocabulary Review 3.Crash Course French Revolution 4.Guided Reading: Revolution.

DESIGNING -Initial ideas

Engineering 1182 College of Engineering Engineering Education Innovation Center Working Drawings Packet / BOM Rev: , AJPAssembly Drawings1.

Engineering 1182 College of Engineering Engineering Education Innovation Center Section Views with SolidWorks Rev: , AJPDimensioning in SolidWorks1.

DRAFTING TECHNIQUES I 136. Here is a basic shape. From here, we will do some advanced drafting once we put this shape on a sheet as a drawing. Select.

Contd. Assign responsibilities Structure team Clarify roles & authority Collect internal, information Select processes.

Dr. Catherine Turner Assembly drawings.

Task 1 OPEN THE DOCUMENT TEST 1 FROM THE 706 DRIVE.

Engineering H191 - Drafting / CAD Gateway Engineering Education Coalition Lect 18P. 1Autumn Quarter Sectioned Assembly Lecture 18.

Technical Drawings and their elements Applications of Technology.

Working / Assembly Drawings

Engineering 1182 College of Engineering Engineering Education Innovation Center Extracting Drawings Rev: , AJPExtracting Drawings1.

Posting from a General Journal to a General Ledger Accounting I Chapter 4, Section 1.

Task 1 OPEN THE DOCUMENT TEST 1 FROM THE 706 DRIVE.

Step one: Page Border and title block. Border will be ¼” from the edge of the paper. Drawing will be done in landscape format. Title block will be 1”

Working Drawings (Production Drawings)

TYPE YOUR STORY TITLE HERE Type your name here PUT A PICTURE HERE.

How to complete the Common Application Form 2015 The CAF (Common Application Form) can be used to apply for City College, Varndean and Bhasvic. If you.

Sectional Views Advanced Drawing Abilities Teacher © J Lewis 2004.

1 4. Principles of Dimensioning This week you will learn dimensioning. The steps to follow are: Functional & Non-functional Dimensions Principles of Dimensioning.

Chapter Name WorksheetName:______________________________________________ Period ______Date _____________ Directions: Do the following reading roadmap.

Instructions/RubricEffective Presentations Student Name Here Presentation Guidelines Choose an appropriate theme, for the following presentation. But,

Cartoon Similarity Using cartoons to draw similar figures

Double click here to add event title Double click here to add event date Double click here to add event time Double click here to add event location.

Reading Working Drawing Packets and Section Views

Jump to first page Craft & Design Final Project Folio.

J.Byrne Correct Incorrect Incorrect 10mm border line all around finishing in a neat sharp corner Title Box Border Lines J.Byrne 2012.

Blueprints. Definition: a reproduction of a technical or engineering design.

Plate No. 5. Make the Border line and Title Block – (5 Minutes ONLY) Divide the workspace and find the reference point – (5 Minutes ONLY) Draw the Isometric.

British Standards BS8888.

Class Work 5.A OBLIQUE VIEW. START 1.DRAW BORDER LINE 2.DRAW TITLE BLOCK 3.WRITE YOUR NAME 4.DIVIDE THE WORK SPACE INTO 4 (200mm – 125mm from border line)

Quarterly Projects. Guidelines  One project per quarter  Different project each quarter  One quarter MUST be book report frame  Each project worth.

Printing Set-up Drawing by switching to Layout 1 Insert a title block.

Reading Working Drawing Packets and Section Views

Higher Graphic Communication Final assignment Student self assessment

Reading Working Drawing Packets and Section Views

Assembly Drawings.

Introduction to New Product Development (Portfolio)

Engineering Drawing Aims:- Introduce typical drawing template.

FUE - Future University in Egypt Faculty of Engineering and Technology Department of Architectural Engineering ARC472 - Execution Design (2) Spring 2017.

Presentation Title Here

Working Drawings (Production Drawings)

MARCH 19, 2018 OBJECTIVE – Students will demonstrate understanding of global warming/climate change. Students will describe different methods scientist.

Contour Lines Topographic Mapping.

Introduction to Engineering 2-D Detail Drawings - 1

Design & Drafting Technology Unit 6

Manufacturing Technical Objects

Photographer’s Name Here

Value Value is an element of art.

Group #? member name Artist’s Name Here.

Scaling The Term Project and adding Dimensions

Cartoon Similarity Using cartoons to draw similar figures

End-of-Book Reflection

Working Drawings (Production Drawings)

LABEL Each of your views should be labelled appropriately. Each label should be in capital letters and should be centred under each view.

Why We Need Car Parking Systems - Wohr Parking Systems

Group #? member name Architect’s Name Here.

Types of Stack Parking Systems Offered by Wohr Parking Systems

Presentation transcript:

March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 1 Working drawings of an Assembly Complete each drawing fully before proceeding on to the next one. Start with #1 and go in sequence thru all parts. Add each part to the assembly drawing after its part drawing is complete. (Example: Complete part #2 and place it in the assembly before going on to part #3.) Use a title block and border of your choice. Make sure you fill out the title block with title, scale, date and author. On the assembly drawing include balloons and part list. Hand in a printed package including the assignment. NOTES: 1.Use section views for clarity where appropriate. 2.You may use “texture” to create the illusion of hatching. 3. Dimensions MUST match original You are not expected to complete all parts in the time frame. Completeness of those parts you do complete is critical. Assignment 14 MEC 1011 Fall 2004 BENCHMARK

March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 2

March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 3

March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 4

March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 5

March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 6

March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 7

March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 8

March 31, 2004 Mary G. Waldo VERMONT TECHNICAL COLLEGE 9