IPX-2000/1800 Series PBX with VIP-450 Configuration Internet Telephony PBX System Copyright © PLANET Technology Corporation. All rights reserved.

This chapter introduces more than PSTN lines in the IP PBX and install the SIP voice gateways with FXO interface as extensions of the PBX system, and the amount of the PSTN interface will be increased to meet the demands. This chapter introduces more than PSTN lines in the IP PBX and install the SIP voice gateways with FXO interface as extensions of the PBX system, and the amount of the PSTN interface will be increased to meet the demands. The ID of the SIP trunk is 555 and to set the route destination number 91. Accordingly, Users could dials 91 switch to gateway FXO port. The ID of the SIP trunk is 555 and to set the route destination number 91. Accordingly, Users could dials 91 switch to gateway FXO port. When remote call PSTN number to gateway, FXO start the Hot line dialing to IP PBX and into IVR system. When remote call PSTN number to gateway, FXO start the Hot line dialing to IP PBX and into IVR system.

3 / 12 Case 32: IP PBX-Trunk-Gateway Configuration Company A, want to expanded PSTN Line decided to create a private SIP trunk to connect Gateway. IP PBX FXO Gateway

4 / 12 Select the [ to create the Routes for the gateway. Select the [Route->Route] of IP PBX to create the Routes for the gateway. 1 Create a Route ID : Create a Route ID :PBX_TO_GW Destination number pattern : 91 Number of stripped digits: 2 Prefix: 555 striped 91 of dialed 555 call be transferred to the gateway. This Route is for user to dial 91 then striped 91 of dialed 555 call be transferred to the gateway. 2 Case 32: IP PBX-Trunk-Gateway Configuration

5 / Select the [ to add the previous Routes to a Routegroup Select the [Route->Routegroup] of IP PBX to add the previous Routes to a Routegroup Create a Routegroup to the Routegroup. Create a Routegroup RG_GW_TO_PBX, then add the Route TO_GW_1 and Route TO_GW_2 to the Routegroup. Case 32: IP PBX-Trunk-Gateway Configuration

6 / Select the [ Select the [Trunk->SIP trunk] of IP PBX to create a SIP trunk which connect with Gateway Trunk Trunk identifier: 555 (this number is for Gateway to hot line to auto attendant) Check Dynamic peer Auth. Name: 555 Auth. password: 555 Case 32: IP PBX-Trunk-Gateway Configuration

7 / Select Select the [User->Usergroup] of IP PBX to associate the SIP trunk 555 to corresponding usergroup Associate the Associate the SIP trunk 555 to the usergroup UG_DEF 32: IPPBX-Trunk-Gateway Configuration Case 32: IP PBX-Trunk-Gateway Configuration

8 / Select the [ Select the [Service->IP PBX service] of IP PBX to reload the IP PBX configuration. Click the [] button to reload the IP PBX configuration. After completed the setting of IP PBX then connect to Gateway to finish rest procedures. Click the [Reload] button to reload the IP PBX configuration. After completed the setting of IP PBX then connect to Gateway to finish rest procedures. Case 32: IP PBX-Trunk-Gateway Configuration

9 / 12 Case 32: IP PBX-Trunk-Gateway Configuration  VIP-480 Configuration 1.Reset to factory setting ITG> config erase (Press “y” to erase it) ITG> atpm erase (Press “y” to erase it) ITG> net set fac_default (Press “y” to reboot machine) 2.Network parameters ITG> net set ip (Press “n” don’t reboot machine) ITG> net set mask ITG> net set gateway (Press “n” don’t reboot machine) 3.Port Settings ITG> set coding 0 dtmf_relay on oob ITG> set port 0 dial_in plar 0555 ITG> set port 1 dial_in plar 0555 ITG> set port 2 dial_in plar 0555 ITG> set port 3 dial_in plar 0555

10 / 12 Case 32: IP PBX-Trunk-Gateway Configuration 4.SIP Settings ITG> set sip reg add ITG> set sip auto_reg on ITG> config activate ITG> config store 5.Dial Plan Settings ITG> atpm req ITG> atpm aadd ITG> atpm aadd ITG> atpm hadd ITG> atpm hadd ITG> atpm dadd 11 sip ITG> atpm done ITG> atpm store ITG> net reset (Press “y” to reboot machine)

11 / 12 For example: 1.From IP Phone make a call to FXO. Step 1. Pickup the handset and hearing a dial-tone, then input a number 91#. Step 2. You will be hear a ring-back tone afterward, and then get a dial-tone form PSTN line. Step 3. To input a local phone number, such as From local phone (PSTN) make a call into IP PBX through FXO. Step 1. Pickup the handset of local phone and hearing a dial-tone, input number Step 2. You will be hear a ring-back tone afterward, and then entered the IVR of IP PBX Step 3. To input a extension number of SIP client, then the SIP client should be ring up. NOTE: The mentioned parameters and network settings in this sample be carefully modified to meet the real-world applications.