CONFIGURATION AND SENSOR LAYOUT AC5 AC6 AC7 Accelerometer-AC AC1 HAMMER VibPilot AC4 AC3 AC2 No Gains is used. Calibration Constant are entered manually All sensors is set up in such a way they are measuring positive direction in DAQ settings. Each accelerometer is connected to the channel associated with it’s number (i.e. AC1-Channel 1) (Hammer-Channel 8). S(-) N(+)/x W(+)/y E(-) Hammer Hit Direction z
DETAIL 1 DETAIL 2 DETAIL 3
IN-PLANE MOTION SENSOR DETAILS
SENSOR DETAILS FOR IN-PLANE TESTS* Refer to Detail 1a, 2 and 3 TypeBrandModelSerialRangeAdditional InfoLocationCalibration AC-1PCB - ICPU348B /- 50 g HZ Magnetic Mount A Center / South Side Ground Floor Beam 100 mV/g AC-2PCB - ICPU348B /- 50 g HZ Magnetic Mount A st Floor South Side Gusset Plate 100 mV/g AC-3PCB - ICPU348B /- 50 g HZ Magnetic Mount A nd Floor South Side Gusset Plate 100 mV/g AC-4PCB - ICP353B /- 50 g HZ Magnetic Mount A rd Floor South Side Gusset Plate 100 mV/g AC-5PCB - ICPU348B /- 50 g HZ Magnetic Mount A st Floor, North Side Column, Outside of outer Flange Aligned with beam web 100 mV/g AC-6PCB - ICPU348B /- 50 g HZ Magnetic Mount A nd Floor, North Side Column, Outside of outer Flange Aligned with beam web 100 mV/g AC-7PCB - ICP353B /- 50 g HZ Magnetic Cap A rd Floor, North Side Column, Outside of outer Flange Aligned with beam web 100 mV/g EX-1PCB - ICP086D N Medium Hard Red Plastic Tip mV/N *These configuration is related to the tests where floor sensors are located outside of the flange aligned with web.
SENSOR DETAILS FOR IN-PLANE TESTS* Refer to Detail 1b, 2 and 3 TypeBrandModelSerialRangeAdditional InfoLocationCalibration AC-1PCB - ICPU348B /- 50 g HZ Magnetic Mount A Center / South Side Ground Floor Beam 100 mV/g AC-2PCB - ICPU348B /- 50 g HZ Magnetic Mount A st Floor South Side Gusset Plate 100 mV/g AC-3PCB - ICPU348B /- 50 g HZ Magnetic Mount A nd Floor South Side Gusset Plate 100 mV/g AC-4PCB - ICP353B /- 50 g HZ Magnetic Mount A rd Floor South Side Gusset Plate 100 mV/g AC-5PCB - ICPU348B /- 50 g HZ Magnetic Mount A st Floor, North Side Column, Inside of inner Flange 100 mV/g AC-6PCB - ICPU348B /- 50 g HZ Magnetic Mount A nd Floor, North Side Column, Inside of inner Flange 100 mV/g AC-7PCB - ICP353B /- 50 g HZ Magnetic Cap A rd Floor, North Side Column, Inside of inner Flange 100 mV/g EX-1PCB - ICP086D N Medium Hard Red Plastic Tip mV/N *These configuration is related to the tests where floor sensors are located inside the flange.
In the trial descriptions, this case is referred as: “Aligned with Web”
Detail1b In-Plane W8x67 W10x30 Directionof Measurement Directionof Measurement 5-1/4’’ 2-3/8’’ In the trial descriptions, this case is referred as: “On the Flange”
OUT-OF-PLANE MOTION SENSOR DETAILS
SENSOR DETAILS FOR OUT-OF-PLANE TESTS TypeBrandModelSerialRangeAdditional InfoLocationCalibration AC-1PCB - ICPU348B /- 50 g HZ Magnetic Mount A Center / East Side Ground Floor Beam 100 mV/g AC-2PCB - ICPU348B /- 50 g HZ Magnetic Mount A st Floor East Side Gusset Plate 100 mV/g AC-3PCB - ICPU348B /- 50 g HZ Magnetic Mount A nd Floor East Side Gusset Plate 100 mV/g AC-4PCB - ICP353B /- 50 g HZ Magnetic Mount A rd Floor East Side Gusset Plate 100 mV/g AC-5PCB - ICPU348B /- 50 g HZ Magnetic Mount A st Floor, West Side Column, Web 100 mV/g AC-6PCB - ICPU348B /- 50 g HZ Magnetic Mount A nd Floor, West Side Column, Outside of outer Flange Aligned with beam web 100 mV/g AC-7PCB - ICP353B /- 50 g HZ Magnetic Mount A rd Floor, West Side Column, IOutside of outer Flange Aligned with beam web 100 mV/g EX-1PCB - ICP086D N Medium Hard Red Plastic Tip mV/N