ASTRO® XTSTM 5000 Model II Cover ST. CLAIR COUNTY Digital Portable Radio Interactive End-User Training ST. CLAIR COUNTY Learning Event Description: This learning event provides subscriber unit users an introduction to their unit, its basic operation, and the job aides available for assistance in operation. This is accomplished through the use of video clips, Instructor facilitation and hands-on activities whereby users are able to perform common tasks associated with unit operation. Learning Event Objective: Upon completion, the participant should be able to employ the toolkit resource needed to accomplish an operational task.

Index – 1 of 2 1 Cover 2 Index – 1 of 2 3 Index – 2 of 2 4 XTS 5000 Model II 5 Your Radio 6 Getting Started 7 Fleet Maps – Radio Templates 8 Status Symbols – 1 of 2 9 Status Symbols – 2 of 2 10 Status Alert Tones 11 Installation and Removal Procedures 12 Antenna 13 Battery – 1 of 8 14 Charging the Battery with the IMPRES Adaptive Charger – 2 of 8 15 Using the IMPRES Adaptive Charger – 3 of 8 16 Using the IMPRES Adaptive Charges – Charge Indicator Lights - 4 of 8 17 Using the IMPRES Adaptive Charges – Initial Battery Charge – 5 of 8 18 Using the IMPRES Adaptive Charges – Automatic & Manual Reconditioning – 6 of 8 19 Using the IMPRES Adaptive Charges – Manually Terminating Reconditioning – 7 of 8 20 Using the IMPRES Adaptive Charges – Special Features - 8 of 8 21 Universal Connector Cover 22 Belt Clip 23 RF Adapter (RFA) 24 Public Safety Speaker/Microphone (PSSM) – 1 of 3 25 Public Safety Speaker/Microphone (PSSM) – 2 of 3 26 Public Safety Speaker/Microphone (PSSM) – 3 of 3 27 GENERAL FEATURES 28 Radio On/Off/Volume 29 Call Alert Page – Acknowledge 30 Transmit and Receive

Index – 2 of 2 31 LED Status 32 Time-out Timer 33 16-POSITION SELECT KNOB 34 Talkgroup/Channel Select (16-Position Select Knob) 35 3-POSITION TOGGLE SWITCH 36 Zone Select (3-Position Toggle Switch) 37 2-POSITION CONCENTRIC SWITCH 38 Secure/Clear Transmit (2-Position Concentric Switch) – 1 of 2 39 Secure/Clear Transmit (2-Position Concentric Switch) – 2 of 2 40 TOP BUTTON 41 Emergency – Send (Top Button) – 1 of 3 42 Emergency – Send Emergency Call (Top Button) – 2 of 3 43 Emergency – Send Emergency Call (con’t) (Top Button) – 3 of 3 44 TOP SIDE BUTTON 45 Scan On or Off (Top Side Button) 46 SIDE BUTTON 1 47 Call Alert Respond (Side Button 1) 48 Private Call – Respond (Side Button 1) 49 Display Light (Conventional only) (Side Button 1) 50 SIDE BUTTON 2 51 Nuisance Talkgroup/Channel Delete (Side Button 2) 52 MENU 53 Direct/TalkAround (Menu) 54 Keypad Tones (Mute or Unmute) (Menu) 55 Scan List Edit (Menu) – 1 of 3 56 Scan List Edit (Menu) – 2 of 3 57 Scan List Edit (Menu) – 3 of 3 58 Smart Battery (Menu) 59 HOME Button

XTS 5000 Model II Your Radio Installation and Removal Status Symbols Fleet Map C2 C1 Z2 Z1 Installation and Removal Status Symbols Status Alert Tones Perform Base-Level Tasks a)  Install/Remove Battery b)  Install/Remove Antenna c)  Install/Remove Belt Clip d)  Turn On/Off Radio e)  Identify System busy, Call Alert, Out of Range Tones and Indicators f)   Transmit and Receive (Operate PTT) g)   Select a Talkgroup/Channel h)  Conventional Features

Top Side Button Options 16-Position Select Knob Zone Select Your Radio 2-PositionConcentric Switch Options TalkgroupSelect Direct/TalkAround Display Light Monitor PL Defeat Scan On or Off Secure/Clear Transmit Transmit Inhibit/Smart PTT Secure/Clear Transmit Talkgroup/Channel Select Menu Options Power On/Off Volume Control 10 : 46AM Direct/Talkaround Mute Keypad Tones Scan List Edit (Menu) Smart Battery A CNTY CALL MUTE Control Top PROG BATT Zone Select 3-Position Toggle Switch Options TalkgroupSelect Direct/TalkAround PL Defeat Power Select Scan On or Off Scan List Edit (Switch + Top Button) Scan List Edit (Switch + Top Side Button) Scan List Edit (Switch + Side Button 1) Scan List Edit (Switch + Side Button 2) Scan List Edit (Switch + Menu) Secure/Clear Transmit Transmit Inhibit/Smart PTT Zone Select Emergency Side Buttons Scan On or Off Call Alert Page (Respond)- (T) Private Call (Respond)-(T) Display Light-(Conventional) Nuisance Talkgroup/Channel Delete Push-To-Talk (PTT) Button HOME INTRODUCE tasks to be covered in this session. Have participants pay close attention because they will be performing the tasks afterward. The following tasks will be covered in the session: 1. Install/ Remove Antenna 2. Install/Remove Battery 3. Turn Radio On/Off 4. Set Volume 5. Select a Zone 6. Select a Mode 7. Transmit and Receive 8.  Initiate/Cancel an Emergency Alarm Top Button Options Call Alert Page (Respond) Call Alert Page (Send – One-Touch) Call Alert Page (Send) Call Response Direct/TalkAround Display Light Dynamic Priority Emergency ID Number (View Your) Using Call Button ID Number (View Your) Using Page Button Monitor Nuisance Talkgroup/Channel Delete Phone Call (Place – One-Touch) Phone Call (Place) Phone Call (Respond) Private Conversation Call (Place – One Touch) Private Conversation Call (Place) Private Conversation Call (Respond) Reprogram Request Scan On or Off Site Lock Site View/Search Status/Message Calls Talkgroup/Channel Calls Volume Set Tone Top Side Button Options Call Alert Page (Respond) Call Alert Page (Send – One-Touch) Call Alert Page (Send) Call Response Direct/TalkAround Display Light Dynamic Priority Emergency ID Number (View Your) Using Call Button ID Number (View Your) Using Page Button Monitor Nuisance Talkgroup/Channel Delete Phone Call (Place – One-Touch) Phone Call (Place) Phone Call (Respond) Private Conversation Call (Place – One Touch) Private Conversation Call (Place) Private Conversation Call (Respond) Reprogram Request Scan On or Off Secure/Clear Transmit Site Lock Site View/Search Status/Message Calls Talkgroup/Channel Calls Volume Set Tone Side Button 1 Options Call Alert Page (Respond) Call Alert Page (Send – One-Touch) Call Alert Page (Send) Call Response Direct/TalkAround Display Light Dynamic Priority Emergency ID Number (View Your) Using Call Button ID Number (View Your) Using Page Button Monitor Nuisance Talkgroup/Channel Delete Phone Call (Place – One-Touch) Phone Call (Place) Phone Call (Respond) Private Conversation Call (Place – One Touch) Private Conversation Call (Place) Private Conversation Call (Respond) Reprogram Request Scan On or Off Secure/Clear Transmit Site Lock Site View/Search Status/Message Calls Talkgroup/Channel Calls Volume Set Tone Side Button 2 Options Call Alert Page (Respond) Call Alert Page (Send – One-Touch) Call Alert Page (Send) Call Response Direct/TalkAround Display Light Dynamic Priority Emergency ID Number (View Your) Using Call Button ID Number (View Your) Using Page Button Monitor Nuisance Talkgroup/Channel Delete Phone Call (Place – One-Touch) Phone Call (Place) Phone Call (Respond) Private Conversation Call (Place – One Touch) Private Conversation Call (Place) Private Conversation Call (Respond) Reprogram Request Scan On or Off Secure/Clear Transmit Site Lock Site View/Search Status/Message Calls Talkgroup/Channel Calls Volume Set Tone

Fleet Maps – Radio Templates See the Radio Template for your specific entity

Status Symbols – 1 of 2 Signal Strength Direct/ TalkAround Monitor Scan Battery Status Secure Call Receive View Program Continued.... Explain each status symbol that appears on the radio’s display. Note Icons may not always be illuminated at all times, for example Scan Vs Priority scan. The Dot will only appear when the “priority” group is active.

Status Symbols – 2 of 2

Status Alert Tones Tone Name Tone Information Acknowledge Receipt of a call sent to the central controller Button Press A valid key was pressed on the keypad Call Alert - Receipt of a Call Alert page sent to your radio - Confirmation receipt of a page received sent from your radio Emergency Emergency alarm was sent from your radio Failsoft Radio has lost communication with the central controller Low Battery Weak battery indication No Acknowledge A call to the central controller was not acknowledged Out of Range Radio is out of range of the system Power-up Radio has successfully powered on Private Call I Receipt of a Private Conversation call sent to your radio Private Call Enhanced Prohibit Talkgroup/Channel or talkgroup/channel is not accessible System Busy Talkgroup/Channel, system or target radio is busy Talk Permit Talkgroup/Channel is ready to use Time-out Timer Time-out timer limit has been reached Pressing each speaker icon will play the sound heard from the radio Not all sounds can be demonstrated live, for example Failsoft or system busy.

Installation and Removal Procedures Belt Clip Battery Antenna Public Safety Speaker Microphone Universal Connector RF Adapter

Antenna To install the antenna: Turn the radio off. Screw the antenna (clockwise) into the antenna receptacle on top of the radio. Tighten the antenna firmly with your fingers. To remove the antenna: Unscrew the antenna (counter-clockwise) and remove it from the antenna receptacle on top of the radio. The antenna is color coded according to its frequency range. Radio operators can then refer to an antenna identification table in the users manual to make sure that they have the correct antenna.

Battery – 1 of 8 Continued… To install the battery: Turn the radio off Hold the radio with the back facing upward. Align the three slots at the top of the battery with the three tabs on the back of the radio. Push the battery down toward the radio until the battery clicks into place. To remove the battery: Turn the radio off. Hold the radio with the back of the radio facing upward. Push the battery release button on the bottom of the radio. Lift the battery away from the radio and remove. Continued… Batteries are shipped uncharged, so the user must charge the battery before attempting to use the radio. Make sure the radio is turned off before removing the battery. For installing, slide the lip of the battery into the slot between the three clips and the outside casing at the top of the radio to ensure a proper connection.

Charging the Battery with the IMPRES Adaptive Charger – 2 of 8 You are using the IMPRES Adaptive Charger and IMPRES or SMART Batteries The battery must be charged before use. Memory effect is a phenomenon that causes a loss in battery capacity or voltage due to repetitive shallow discharging or long-term overcharging. This memory effect has been greatly reduced in your batteries through the use of new cell technology. It is still recommended, however, that you discharge your battery as much as possible before recharging it. Recharging after each shift is good standard practice. When charging a battery that is attached to your radio, turn the radio off to ensure a full charge. Continued…

Using the IMPRES Adaptive Charger – 3 of 8 IMPRES Charger Monitors the usage pattern of the IMPRES battery and, Stores that information in the IMPRES battery, then Performs a recondition cycle only when needed. Will not overheat the battery regardless of how long it is left in the charger. Charger monitors the battery and automatically “tops off” the battery, as required. NOTE: IMPRES batteries may be charged in conventional chargers. However, the Smart Energy features will not be enabled. Continued....

Using the IMPRES Adaptive Charges – Charge Indicator Lights - 4 of 8 Charge Indicator Description Single Flash Green Charger has successfully powered up. Steady Red Battery is in rapid charge mode. Flashing Green Battery has completed rapid charge (>90% available capacity). Battery is in Top-Off charge (Trickle Charge) and requires approximately 1 hour. Steady Green Battery has completed charging and is fully charged. Flashing Yellow Battery is recognized by charger but is waiting to charge. (Either the battery voltage is too low or the battery temperature is too low or too high to allow charging. When this condition is corrected, the battery will begin charging). Flashing Red Battery is unchargeable or not making proper contact. Steady Yellow Battery is in recondition mode. The length of time the charger remains in this mode is dependent upon the state of charge remaining in the battery when inserted. (Fully charged batteries require more time to recondition–8 hours or more–than fully discharged batteries.) Flashing Red & Green Battery may be approaching the end of its rated service life. This is not a fault indication, merely a notification to the user that the battery may soon no longer be able to yield expected service and may need to be replaced. Continued....

Using the IMPRES Adaptive Charges – Initial Battery Charge – 5 of 8 1. Must be in an IMPRESS Adaptive Charger to properly calibrate the IMPRES battery and enable the Smart Energy features. This process is indicated by a STEADY YELLOW indicator light. The process is automatic and includes an initial reconditioning and then begins charging upon completion of this process. To ensure optimum performance prior to the initial use, all new batteries should be left in the charger until the light turns solid green. If this process is interrupted, the charger will calibrate the battery upon the next insertion. NOTE: New batteries (never used before) may prematurely indicate a full charge (STEADY GREEN indication). Continued....

Using the IMPRES Adaptive Charges – Automatic & Manual Reconditioning – 6 of 8 Automatic Reconditioning of the Battery: When the IMPRES battery is properly inserted into the charger, the charger determines if it is appropriate to recondition the battery. If the battery needs reconditioning, the charger automatically indicates a STEADY YELLOW. This process may take up to 8 hours or more to complete, depending upon the state of charge and capacity rating of the battery when inserted. NOTE: It important that the battery be allowed to complete the recondition/recharge process for it to be effective. Leave the battery in the charger until the charger indicates a STEADY GREEN. Manual Reconditioning of the Battery: Within 2 ½ minutes of the initial insertion of an IMPRES battery (STEADY RED indication), remove and reinsert the battery within 5 seconds to manually force reconditioning to occur. The charger indicator changes from a STEADY RED to a STEADY YELLOW. This forces the charger to recondition and automatically recharge the battery. NOTE: Excessive use of this feature reduces the cycle life of the battery. Continued....

Using the IMPRES Adaptive Charges – Manually Terminating Reconditioning – 7 of 8 At any time during the reconditioning process (STEADY YELLOW indication), remove and reinsert the battery within 5 seconds. This causes the charger to terminate the reconditioning process and begin the charging process. The charger indicator changes to a STEADY RED. NOTE: The conditioning charge feature creates an audible “ticking” sound in the receiving radio during the rapid and trickle charge modes of operation. This sound is caused by periodic discharge pulses to the battery. Changing the switch position located on the bottom of the charger from position “A” to position “B” reduces the frequency of the discharge pulses. This has a minimal impact on the effectiveness of the charger. Toward the end of the rapid charge cycle (STEADY RED indication), the battery voltage exceeds the normal operating voltage of the radio. Voltage returns to a normal level following the rapid charge mode or when the battery is removed from the charger. If the radio is turned on while the charger is in rapid charge mode, the radio becomes temporarily inoperable. This condition can be cleared by removing the radio from the charger and turning the radio off and on again. During the reconditioning process, the battery becomes fully discharged. As a result, the radio may not function during reconditioning mode. Continued....

Using the IMPRES Adaptive Charges – Special Features - 8 of 8 If the IMPRES battery is charged for > 2 ½ minutes, the IMPRES Adaptive Charger retains the serial number of the IMPRES battery. The battery can be removed from the charger for up to 30 minutes. Once the battery is reinserted back into the charger, it will resume the charging process from that point when the battery was first removed.

Universal Connector Cover The universal connector cover protects the side connector near the antenna. To remove the cover: Turn the radio off. Carefully insert a flat-bladed screwdriver between the bottom of the cover and the connector. Holding the top of the cover with your thumb, push the screwdriver gently downward and lever the cover away from the radio. To install the cover: Insert the hooked end of the cover into the slot above the connector. Rub the ball of your thumb from the top to the bottom of the cover, applying pressure towards the radio. This will flex the cover and snap it into place. Remember to turn off the radio. The cover should be on the radio any time the operator is not using the radio with an accessory.

Belt Clip 1 2 To install the belt clip: Remove the battery before installing or removing the belt clip. Hold the battery with the back of the battery facing you. Hold the belt clip with the top facing upward, and align the clip with the slots on the battery back. Slide the belt clip downward into the slots until it clicks into place. To remove the belt clip: Pull away the metal tab at the top of the battery clip from the battery. Slide the clip upward until it comes away from the radio. 1 2 Remind students to remove the battery from the radio before installing or removing the belt clip. Indicate where and how to align with the slots for easy assembly. Do not use too much force to pull metal tab to remove clip.

RF Adapter (RFA) To install the RF adapter (RFA): Turn the radio off. Remove the antenna. With your hand above the RFA, hold the RFA in the upright position using your thumb and finger and position it on the radio antenna bushing. Turn the RFA collar and housing (together) clockwise to engage the collar with the threads on the outside of the radio antenna bushing. Turn it until it has rotated between one and two full turns. Watch the position of the collar and connector target to count the number of turns. If it becomes difficult to turn, DO NOT FORCE IT. While maintaining downward pressure on the properly oriented switch housing, place the custom wrench all the way onto the RFA collar’s wrench flats. The wrench will be captured by the collar and will be unable to slip upward or downward. Turn the wrench in increments until the RFA is tightened very securely to the antenna bushing (10-14 turns). You have to start the screwing process of the RFA with the one or two turns by hand. Once you complete that initial process, then use the provided wrench to begin tightening the unit to the radio.

Public Safety Speaker/Microphone (PSSM) – 1 of 3 To install the PSSM: Turn the radio off. Follow the instructions for removing the universal connector cover. Attach the accessory connector to the radio’s universal connector as follows: a. Make sure the RF adapter has been installed in your radio before continuing with installation. b. Looking at the antenna side of the radio, insert the bottom hooked end of the accessory connector into the slot below the universal connector. c. While holding the accessory connector seated in the bottom slot, pivot the top of the accessory connector toward the radio until its RF interface connector aligns with the circular contact target on the RF adapter, then engage the accessory connector’s spring-loaded latch in the radio’s top slot. Continued.... Remember that receiver audio will be heard only from the accessory speaker while the accessory is attached to the radio. Set the high/low switch on the public safety speaker microphone to the “low” position to monitor audio at a low volume; for a high volume level, set the switch to the “high” position. The public safety speaker/ microphone performs best when it is operated with the antenna above the user’s shoulder.

Public Safety Speaker/Microphone (PSSM) – 2 of 3 Attach the correct (frequency-sensitive) antenna to the PSSM by screwing the antenna’s threaded end into the threaded antenna jack on top of the PSSM’s housing. Rotate the antenna clockwise into the jack until it seats firmly. The public safety speaker/microphone performs best when it is operated with the antenna above the user’s shoulder. To transmit using the public safety speaker/microphone, press the PSSM’s PTT and speak into the microphone’s grille area. The red light-emitting diode (LED) on top of the radio will light, indicating that the radio is in the transmit mode. If a more permanent attachment is desired after the accessory connector is latched to the radio, secure the latch to the connector housing using the screw supplied. Continued.... Remember that receiver audio will be heard only from the accessory speaker while the accessory is attached to the radio. Set the high/low switch on the public safety speaker microphone to the “low” position to monitor audio at a low volume; for a high volume level, set the switch to the “high” position. The public safety speaker/ microphone performs best when it is operated with the antenna above the user’s shoulder.

Public Safety Speaker/Microphone (PSSM) – 3 of 3 To remove the PSSM: Turn the radio off. Rotate the antenna counter-clockwise to unscrew it from the jack. Remove the accessory connector by pivoting the top of the accessory connector away from the radio until it disengages from the RF adapter. Follow the instructions for attaching the universal connector cover. Remember that receiver audio will be heard only from the accessory speaker while the accessory is attached to the radio. Set the high/low switch on the public safety speaker microphone to the “low” position to monitor audio at a low volume; for a high volume level, set the switch to the “high” position. The public safety speaker/ microphone performs best when it is operated with the antenna above the user’s shoulder.

GENERAL FEATURES

Radio On/Off/Volume On/Off/Volume Knob To turn the radio on: Turn the On/Off/Volume Control knob clockwise. If the power-up test is successful, you briefly see SELF TEST, then the home display. If enabled, a power-up tone is also heard. If the power-up test is unsuccessful, you see ERROR XX/YY. (XX/YY is an alphanumeric code.) To turn the radio off: Turn the On/Off/Volume Control knob counter-clockwise until it clicks. On/Off/Volume Knob SELF TEST The LED lights green when you turn the radio on. The radio will display an error message if it fails the self test. Adjust the Volume to a comfortable level.

Call Alert Page – Acknowledge When a Call Alert Page is received, you hear four repeating alert tones, the LED flashes green, the call received symbol ( ) flashes and PAGE RECEIVD Is displayed. To respond to a Call Alert Page: Press any button or change talkgroup/channel to acknowledge the page and clear the alert from your radio. Note: The radio that initiated the Call Alert page will receive a return acknowledgment when the Call Alert page is received. PAGE RECEIVD MUTE PROG BATT LED IMPORTANT Standard Operating Procedure Return to your primary dispatch (HOME or A1) and Respond to Dispatch. Demonstrate responding to a Call Alert page. The page will continue to remind you until cleared, just as a beeper would continue to beep until acknowledged.

Transmit and Receive LED Push-to-Talk (PTT) Continued.... To transmit: Select the desired zone/talkgroup/channel. Listen for ongoing conversations; if the talkgroup/channel becomes clear, proceed with your call. Press and hold the PTT button to transmit and wait for the “Talk Permit” tone. The LED will light red. When speaking, keep the microphone 1-2" from your mouth. Note: If you do not hear a Talk Permit tone, your system administrator has preprogrammed the tone to be off. Release the PTT button to receive (listen). LED Push-to-Talk (PTT) Continued.... The user must wait until the red LED is lit before speaking. The system has a short delay before transmitting. The red LED blinks on and off when the radio receives a transmission. Demonstrate how the user can adjust the volume for a comfortable listening level.

LED Status RED GREEN Continued.... Solid - PTT is pressed; radio is transmitting Flashing - Talkgroup/Channel Busy - Low Battery (lights while transmitting) GREEN Solid - Self-test being performed Flashing - Incoming Private Call RED LED GREEN LED Continued.... Describe the LED status, red VS green and solid VS flashing.

Time-out Timer LED Push-to-Talk (PTT) The time-out timer turns off your radio’s transmitter. The timer is set for 60 seconds. Hold down the PTT button longer than the programmed time. You will hear a low-pitched warning tone, the transmission will cut off, and the LED will go out until you release the PTT. Release the PTT button. The LED will re-light and the timer will reset. Press the PTT button to re-transmit. The time-out timer restarts. The timer will restart and the LED lights red. LED Push-to-Talk (PTT)

16-POSITION SELECT KNOB

Talkgroup/Channel Select (16-Position Select Knob) Name To select a talkgroup/channel: Turn the Talkgroup/Channel Select knob to select the desired talkgroup/channel. The new name will appear on the display. If the talkgroup/channel you selected is unprogrammed, repeat the above step. Talkgroup/Channel Select Knob A CNTY CALL MUTE PROG BATT NOTE: Position 16 is an Emergency Talkgroup that will always be monitored by dispatch The display will indicate your selection as you turn the 16-Position Select Select knob on top of the radio.

3-POSITION TOGGLE SWITCH

Zone Select (3-Position Toggle Switch) To select a zone: Toggle the Zone Select switch to select the desired zone. If the zone you selected is unprogrammed, repeat step 1. Press the Home button to confirm the displayed zone and talkgroup/channel. Zone Name A CNTY CALL MUTE PROG BATT Zone Select Switch Explain that the Zone switch is limited to 3 zones, if more zones are programmed, they will be accessed through the menu.

2-POSITION CONCENTRIC SWITCH

Secure/Clear Transmit (2-Position Concentric Switch) – 1 of 2 Today The following talkgroups are encrypted for all transmit and receive functions: SHRF DTU SHRF INV In the Future Talkgroups may have encryption capabilities that will require the radio user to use the Concentric Switch to change from secure to clear and clear to secure transmissions. The radio will receive encrypted calls without enabling the Secure switch, but to transmit in secure, the Secure switch must be enabled. Secure/Clear Switch A CNTY CALL MUTE PROG BATT Secure Clear Continued.... When you have selected a secure-ready talkgroup/channel, you can communicate knowing that you’re transmission is scrambled against unwanted eavesdroppers.

Secure/Clear Transmit (2-Position Concentric Switch) – 2 of 2 To select secure transmissions: Turn the Secure/Clear switch to the predetermined secure position ( ). Note: If the selected talkgroup is programmed for clear-only operation, you will be unable to transmit in secure. If you press the PTT button, you will see CLR TX ONLY displayed, and you will hear an invalid mode tone. The radio will not transmit until you set the Secure/Clear switch to the clear position ( ). To select clear transmissions: Turn the Secure/Clear switch to the predetermined clear position ( ). Note: If the selected talkgroup is programmed for secure- only operation, you will be unable to transmit in clear. If you press the PTT button, you will see SEC TX ONLY displayed, and you will hear an invalid mode tone. switch to the secure position ( ). Secure/Clear Switch A CNTY CALL MUTE PROG BATT Secure Clear When you have selected a secure-ready talkgroup/channel, you can communicate knowing that you’re transmission is scrambled against unwanted eavesdroppers. .

TOP BUTTON

Emergency – Send (Top Button) – 1 of 3 To send an emergency signal from your radio: EMERGENCY MUTE PROG BATT Send an emergency call. Emergency Button

Emergency – Send Emergency Call (Top Button) – 2 of 3 To send an emergency call: Press the orange Emergency button. Your radio reverts to emergency status and has priority access to the EMRGNCY 1 talkgroup. *an audible alert is heard and displayed at every dispatch console in CENCOM The radio operates in the normal manner while in emergency call status, except you are no longer on your selected talkgroup. You talk on the preprogrammed emergency talkgroup - EMRGNCY 1 - that is monitored by dispatch. The emergency alarm is sent on this same talkgroup. The current zone/talkgroup is displayed alternately with EMERGENCY, the LED lights red. NOTE: If you are selected to a conventional channel, you may not be able to send an emergency call. When you press the orange button, your radio will emit a prohibit tone indicating that the emergency function is not available on the selected channel. EMERGENCY MUTE PROG BATT LED Emergency Button Continued.... Enabling an Emergency state assigns you priority access to a talkgroup/channel to ensure the greatest ease of communication. It also alerts the necessary people of your status, keeping them appraised of your situation.

Emergency – Send Emergency Call (con’t) (Top Button) – 3 of 3 To Exit/Clear an Emergency: NEVER CLEAR AN EMERGENCY WITHOUT BEING INSTRUCTED TO DO SO BY DISPATCH. *See St. Clair County SOP for proper emergency procedure Press and hold the Emergency button for a few seconds until you hear a dull tone. The radio display will no longer display EMERGENCY, AND Your radio will revert to your selected talkgroup. EMERGENCY MUTE PROG BATT Push-to-Talk (PTT) Push-to-Talk (PTT) Enabling an Emergency state assigns you priority access to a talkgroup/channel to ensure the greatest ease of communication. It also alerts the necessary people of your status, keeping them appraised of your situation.

TOP SIDE BUTTON

Scan On or Off (Top Side Button) The scan feature allows you to monitor traffic on different talkgroups/channels by scanning a preprogrammed list of talkgroups/channels. Your radio has two different scan lists - Priority Monitor Scan (trunked) and Talkgroup Scan (conventional). To turn scan on: Press the Scan button. The scan status symbol ( ) is displayed, indicating scan is active. To turn scan off: The scan status symbol ( ) will no longer be displayed, indicating scan has been deactivated. Scan Button A CNTY CALL MUTE PROG BATT Note: If you are selected to a trunked talkgroup when you turn scan on, you will be using Priority Monitor Scan. Priority one = Selected Talkgroup Priority two = Primary Dispatch Talkgroup * You cannot nuisance delete a priority member. All remaining members are non-priority. If you are selected to a conventional channel when you turn scan on you will be using Talkgroup Scan. All scan members have equal priority and will not interrupt each other. Scanning allows you to monitor different talkgroup/channel automatically. If there is activity on a talkgroup/channel, Scan will automatically take you to that talkgroup/channel.

SIDE BUTTON 1

Call Alert Respond (Side Button 1) When a Call Alert page is received, you hear four repeating alert tones, the LED flashes green, the call received symbol ( ) flashes and PAGE RECEIVD Is displayed. To respond to a Call Alert Page: Press the Call Alert Respond button. Press the PTT button to talk; release it to listen. Press the Home button to exit the call. PAGE RECEIVD MUTE PROG BATT LED IMPORTANT Standard Operating Procedure Return to your primary dispatch (HOME or A1) and Respond to Dispatch. Call Alert Respond Button Push-to-Talk (PTT)

Private Call – Respond (Side Button 1) When a Private Call is received, you hear two alert tones, the LED flashes green, the call received symbol ( ) flashes and CALL RECEIVD is displayed. To respond to a Private Call: Press the Private Call Respond button within 20 seconds. Press and hold the PTT button to talk; release it to listen. Press the Home button or the Private Call Respond Button to hang up and return to the home display. CALL RECEIVD MUTE PROG BATT LED Private Call Respond Button Push-to-Talk (PTT) It is important to access Private Conversation Call within 20 seconds to respond, otherwise, if you just press the PTT, you will transmit to the entire group and not as a Private Conversation Call. Press the PTT button to talk with the calling party. It is important that both parties release the talkgroup/channel, otherwise the talkgroup/channel will be blocked for other's use.

Display Light (Conventional only) (Side Button 1) If poor light conditions make the display or talkgroup/channel numbers (around the 16-Position Select knob) difficult to read: Turn on the radio’s backlights by pressing the Light button. These lights will remain on for a preprogrammed time before they turn off automatically. OR You can turn them off immediately by pressing the Light button again. Display Light Button Use the light only when needed as the light will drain battery power more quickly.

SIDE BUTTON 2

Nuisance Talkgroup/Channel Delete (Side Button 2) When the radio scans to a talkgroup/channel that you do not wish to hear (nuisance talkgroup/channel), you can temporarily delete the talkgroup/channel from the scan list. To delete a nuisance talkgroup/channel: When the radio is locked onto the talkgroup/channel to be deleted, press the Nuisance Delete button. Repeat this step to delete more talkgroups/channels. Note: You cannot delete a priority talkgroup ( ) or the designated transmit talkgroup/channel. The radio continues scanning the remaining talkgroups/channels in the list. To resume scanning the deleted talkgroups/channels, change talkgroups/channels or turn scan off and then back on again. A CNTY CALL MUTE PROG BATT You can only Nuisance Delete one talkgroup/channel at a time. If you Nuisance Delete another talkgroup/channel, you will push the first deleted talkgroup/channel back into rotation.

MENU

Direct/TalkAround (Menu) Applies only to SC I-CALL and SC I-TAC 1-4. Also known as “talk-around operation,” direct lets you bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. To directly connect with another radio: Select a conventional channel from the fleet map list provided by your system administrator. Press the right side of the 4-way Navigation button until DIR is displayed. Press the button directly below DIR. You momentarily see the current operation displayed – DIRECT MODE or RPTR MODE. Press the button directly below DIR or RPTR to select the desired mode. Pressing the Home button without making a selection will exit without changing the current mode. Note: If DIR is selected, the direct symbol ( ) and DIRECT MODE are displayed. DIRECT MODE DIR RPTR Use this feature when you have line-of-sight confirmation with the other unit. You have a decreased range of communication when using Direct. You will not receive normal system communication when the feature is engaged.

Keypad Tones (Mute or Unmute) (Menu) To turn the keypad tones on or off: Press the right side of the 4-way Navigation button until MUTE is displayed. Press the button directly below MUTE. The current state is shown – TONES OFF or TONES ON. Press the button directly below OFF or ON. Note: Press the Home or the PTT button to exit without changing the setting. Note: Turning off keypad tones does not affect any other tones. A CNTY CALL POL DISP NW MUTE PAGE PROG MUTE BATT CALL Push-to-Talk (PTT)

Scan List Edit (Menu) – 1 of 3 This feature lets you change scan list members and priorities. To edit the scan list: Press the right side of the 4-way Navigation button until PROG is displayed. Press the button directly below PROG Press the right side of the 4-way Navigation button until SCAN is displayed. Press the button directly below SCAN. You see the first available item and the view/program ( ) symbol flashing, indicating the programming mode. You will also see SEL, DEL, and RCL displayed as possible selections. Press the left or right side of the 4-way Navigation button to select the item to be changed. Continued.... A CNTY CALL MUTE PROG BATT Remember to locate the list member before adding or deleting using View List. The programming icon will flash during programming, unlike during View when it remains on steadily.

Scan List Edit (Menu) – 2 of 3 Press the button directly below SEL or DEL or RCL. SEL = add the currently displayed item to the scan list. DEL = delete the currently displayed item from the scan list. RCL = view the next available item. OR When adding a priority member press the button directly below SEL additional times. You will see or or with a flashing dot. = this item is in the scan list. = this item is in the scan list as a priority-two member. (dot flashing) = this item is in the scan list as the priority-one member. Note: Priorities are preprogrammed for trunking scan Priority one = Selected Talkgroup Priority two = Primary DispatchTalkgroup You cannot nuisance delete a priority member. Continued.... A CNTY CALL DEL SEL RCL Remember to locate the list member before adding or deleting using View List. The programming icon will flash during programming, unlike during View when it remains on steadily.

Scan List Edit (Menu) – 3 of 3 Press the left or right side of the 4-way Navigation button to select more items to be added or deleted. OR Use the 16-Position Select knob to select additional items to be added or deleted. Press the Home button to exit scan list programming and return to the home display. 16-Position Select Knob A CNTY CALL Remember to locate the list member before adding or deleting using View List. The programming icon will flash during programming, unlike during View when it remains on steadily.

Smart Battery (Menu) This feature allows you to view the condition of your Smart Battery. To access information about your battery: Press the right side of the 4-way Navigation button until BATT is displayed. Press the button directly below BATT. Battery data is displayed as follows: CAPACITY indicates the current charge on the battery. INIT indicates the date of the initial use of the battery. EST CHGS indicates the estimated number of charges on the battery. Note: If a Smart Battery is not powering your radio, the display will read SMART BATT DATA NOT AVAILABLE. A CNTY CALL MUTE PROG BATT

HOME Button Using the HOME button: Press the HOME button to exit a programming mode OR Press and hold the HOME button to return to A1 - your primary dispatch A CNTY CALL MUTE PROG BATT HOME Button