VINYL PIPES U-PVC HI-PVC & FITTINGS JIS SERIES

ASAHI AV VINYL PIPES – U-PVC (HI-PVC) VP and VM PIPES Nominal Size Identification Outer diameterThickness Approx. Inner diameter Length Calculated Weight (kg/m) HI-PVC VP pipe Basic Dimension Max. Min. Tolerance ( ) Average Tolerance ( ) Min. Dimension Tolerance ( ) 13VP , Available 16VP , Available 20VP , Available 25VP , Available 30VP , Available 40VP , Available 50VP , Available 65VP , Available 75VP , Available 100VP , Available 125VP , Available 150VP , Available 200VP , Available 250VP , VP , VM , VM , UNIT: mm Notes; 1.The maximum outer diameter(minimum diameter) is the largest(smallest) of outer diameter measurement at a location. 2.The average outer diameter is the average for outer diameter measurements made in a direction other than two parallel direction or a circumference measurement divided by The mass per unit length(m) in the table, which was calculated using a specific gravity of U-PVC(1.43) is only for information, not part of standards. 4.The length tolerance is +10mm or –10mm. 5.The pipe of VM350 and VM400 are confirmed as JIS K 6741 standard. 6.The pipe of HI-PVC is confirmed as JIS K6742 standard. VP and VM plane end pipe U-PVC JIS K 6741 or 6742 VP plane end pipe HI-PVC JIS K 6742

ASAHI AV VINYL PIPES – U-PVC VU PIPES Nominal Size Identification Outer diameterThickness Approx. Inner diameter Length Calculated Weight (kg/m) Basic Dimension Average Tolerance ( ) Min. Dimension Tolerance ( ) 40VU , VU , VU , VU , VU , VU , VU , VU , VU , VU , VU , VU , VU , VU , VU Pipe - JIS K6741 UNIT: mm Notes; 1.The maximum outer diameter(minimum diameter) is the largest(smallest) of outer diameter measurement at a location. 2.The average outer diameter is the average for outer diameter measurements made in a direction other than two parallel direction or a circumference measurement divided by The mass per unit length(m) in the table, which was calculated using a specific gravity of U-PVC(1.43) is only for information, not part of standards. 4.The length tolerance is +10mm, –10mm. VU Plane end pipe U-PVC

ASAHI AV TS FITTINGS Common Dimension for TS Socket Connection Taper : 1/T Nominal Size 13mm to 50mmNominal Size 65mm to 150mm JIS K Nominal Size d1 Tolerance ( ) l 1/TDDT D, DT Tolerance d (Minimum) Outer diameter of pipe / / * / / / * / / * / / / * / / / * / / UNIT: mm Notes; 1.Tolerance for dimension ( l ) is +4mm, -0.5mm. 2.Sizes marked with * are according to AV original standard. + -

ASAHI AV TS FITTINGS 90º ELBOW Nominal Size DtHHI-PVC Available 16* Available Available Available 28* Available 35* Available Available 65* Available 75* Available 100* Available 125* Available 150* Available UNIT: mm Nominal Size 13mm to 50mm Nominal Size 65mm to 150mm SOCKET Notes; 1.Tolerance for dimension (H) is +4mm, -0.5mm. 2.Sizes marked with * are according to AV original standard. Nominal Size 13mm to 50mm Nominal Size 65mm to 150mm Nominal Size DLHI-PVC Available 16*29.067Available Available Available 28* Available 35* Available Available 65* Available Available Available 125* Available Available UNIT: mm Notes; 1.Tolerance for dimension (L) is +4.0mm, -4.0mm. 2.Sizes marked with * are according to AV original standard. JIS K

ASAHI AV TS FITTINGS REDUCING SOCKET Nominal Size DtD1t1LHI-PVC *16 x Available 20 x Available *20 x Available 25 x Available *25 x Available 25 x Available 30 x Available 30 x Available *40 x Available 40 x Available 40 x Available *50 x Available *50 x Available 50 x Available 50 x Available *65 x Available *65 x Available *75 x Available 75 x Available *75 x Available 100 x Available *125 x Available 150 x Available *150 x Available UNIT: mm 1.Tolerance for dimension (L) is +4mm, -4mm. 2.Sizes marked with * are according to AV original standard. Nominal Size 65mm to 150mm Nominal Size 13mm to 50mm Notes; JIS K

ASAHI AV TS FITTINGS TEE Nominal Size DtHH1HI-PVC Available 16* Available Available Available 28* Available 35* Available Available 65* Available Available Available 125* Available Available UNIT: mm Notes; 1.Tolerance for dimension (H) is +5mm, -1mm. 2.Sizes marked with * are according to AV original standard. Nominal Size 13mm to 50mm Nominal Size 65mm to 150mm CAP Nominal Size DtLHI-PVC Available 16* Available Available Available 28* Available 35* Available Available 65* Available Available Available Available UNIT: mm 1.Tolerance for dimension (L) is +5mm, -0mm. 2.Sizes marked with * are according to AV original standard. 3.Dimension of R is from 1mm to 5mm. Nominal Size 13mm to 50mm Nominal Size 65mm to 150mm Notes; JIS K

ASAHI AV TS FITTINGS REDUCING TEE UNIT: mm Notes; 1.Tolerance for dimension (H and H1) is +5mm, -1mm. 2.Sizes marked with * are according to AV original standard. Nominal Size 65mm to 150mmNominal Size 13mm to 50mm Nominal Size DtHD1H1HI-PVC *65 x Available *65 x Available 75 x Available 75 x Available 75 x Available *75 x Available 100 x Available 100 x Available *125 x Available *125 x Available 150 x Available 150 x Available *150 x Available JIS K

ASAHI AV TS FITTINGS FAUCET ELBOW Nominal Size DtD1D2 l1l1 l2l2 THH1ThreadHI-PVC Rp ½Available Rp ½Available Rp ¾Available Rp 1Available UNIT: mm Notes; 1.Tolerance for dimension (H) is +5mm, -1mm. 2.Tolerance for dimension (H1) is +5mm, -2mm 3.Tolerance for dimension ( l 2 ) is +1mm, -1mm. Caution; 1.Use seal tape and gasket at thread connection. 2.Do not use for connection between metal piping and U-PVC(HI-PVC) piping. 3.Please set proper piping support around Elbow.

ASAHI AV TS FITTINGS 45º ELBOW Nominal Size DtHHI-PVC Available Available UNIT: mm Notes; 1.Tolerance for dimension (H) is +5mm, -1mm. JIS K

ASAHI AV FITTINGS AV 45º BEND Nominal Size DdtLRHI-PVC Available Available Available Available Available Available Available UNIT: mm AV 90º BEND Nominal Size d1d2 l DD1tLR UNIT: mm

ASAHI AV LARGE SIZE FITTINGS AV SHORT ELBOW Nominal Size d1d2 l DtLRHI-PVC Available UNIT: mm AV 90º BEND Nominal Size d1d2 l DD1tLR UNIT: mm

AV 45º BEND Nominal Size DdtLRHI-PVC Available UNIT: mm ASAHI AV LARGE SIZE FITTINGS Nominal Size90 ELBOW45 BEND SHORT ELBOW SOCKET (Thick Wall) REDUCING SOCKET TEE REDUCING TEE Maximum Permissible Working Pressure for AV Large Size Fittings at ambient temperature UNIT: MPa Maximum working pressure includes water hammer pressure on hydrostatic pressure.

ASAHI AV LARGE SIZE FITTINGS AV SOCKET (THICK WALL) Nominal Size d1d2 l DdZLHI-PVC Available UNIT: mm AV REDUCING SOCKET Nominal Sized1d2 l1l1 D1d3 l2l2 D2LHI-PVC 200 x x UNIT: mm

ASAHI AV LARGE SIZE FITTINGS AV TEE Nominal Size d1d2 l DdtLHI-PVC Available UNIT: mm AV REDUCING TEE Nominal Sized1d2 l1l1 D1d3d4 l2l2 D2H l3l3 L 200x x x x x x x UNIT: mm