Metalwork Lathe JF 2007

The Lathe Click on an area to start questions. 3 Jaw Chuck Safety 3 Jaw Chuck Head stock Tool post Tail stock 1 Tail stock 2 Tools for the lathe. Click on tool for question. How to centre the cutting tool How to face off your work Saddle JF 2007

3 Jaw Chuck Safety 1 Which 1 of the following is a safety requirement when using a 3 jaw chuck? 1.Make sure that work piece is secure.Make sure that work piece is secure. 2.Ensure that you are using the correct metal for the work. 3.The compound slide set to the correct angle JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Your answer is- CORRECT Well done try another area of the lathe!! Just click the arrow JF 2007

3 Jaw Chuck Point out the tool that is used to secure your work piece in the 3 jaw chuck. 1.Chuck key.Chuck key. 2.Parting off tool. 3.Centre drill 4.Outside callipers JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Head Stock The head stock contains the gears to make the chuck revolve. State another 2 functions of the head stock 1. To control the angle the metal is set at. 4. To reduce the diameter of the metal. 3. To hold the lathe tool. 6. For drilling holes. 5. To control the speed of the chuck. 2. To control the direction of the chuck. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Your answer is- CORRECT Now see if you can find the 2 nd answer! 1. To control the angle the metal is set at. 2. To hold the lathe tool. 3. To reduce the diameter of the metal. 4. To control the speed of the chuck. 5. For drilling holes. JF 2007

Your answer is- CORRECT Now see if you can find the 2 nd answer! 1. To control the angle the metal is set at. 2. To control the direction of the chuck. 3. To hold the lathe tool. 4. To reduce the diameter of the metal. 5. For drilling holes. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Tool Post What type of tools would be placed on a tool post? 3. Knife, round nose, parting, form and knurling tools. 2. Revolving centre, half centre and face plates. 1. Centre drills, twist drills 4. Taps and dies. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Tail stock 1 Tail stocks use a revolving centre/ half centre to help hold a long work piece in place. What else can they be used for? 1. To help with the tapering process. 4. Helps to measure the diameter of the work piece. 3. Helps cutting with a parting off tool. 2. Can hold centre drills and twist drills. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Tail stock 2 A chuck can be mounted onto the tail stock, what is the name of this chuck? 4. Jacob’s chuck. 1. Morton chuck. 3. Quick realise chuck. 2. Chuck key. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Tools Chose 1 of the following that you think is the tool that is shown here. 1. Parting off tool. 2. Twist drill 3. Revolving centre. 3 Jaw chuck. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Tools Look at this picture. A work piece is being removed from a round brass bar. Name the lathe tool used in this process. 1. Round nose tool. 2. Parting off tool. 3. Form tool. 4. Knife tool. JF 2007

Tools This tool is used to put a diamond shape pattern into metal to provide a grip. What is the name of the tool. 1. Micrometer. 2. Die. 3. Half centre. 4. Knurling tool. JF 2007

Tools Look at the picture of the drill. Point out what type of drill this is. 1. Centre drill. 2. Twist drill. 3. Masonry drill 4. Hand drill JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Compound slide. 2. Head stock. 3. Cross slide. 4. Tail stock Jaw chuck. 6. Revolving centre 7. Tool post. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Compound slide. 2. Head stock. 3. Cross slide. 4. Tail stock Jaw chuck. 6. Revolving centre JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Compound slide. 2. Head stock. 4. Tail stock Jaw chuck. 6. Revolving centre JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Head stock. 2. Cross slide. 3. Tail stock Jaw chuck. 5. Revolving centre JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Compound slide. 2. Head stock. 3. Tail stock Jaw chuck. 5. Revolving centre 6. Tool post. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Compound slide. 2. Head stock. 3. Tail stock Jaw chuck. 5. Revolving centre JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Head stock. 2. Tail stock Jaw chuck. 4. Revolving centre 5. Tool post. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Head stock. 2. Cross slide. 3. Tail stock Jaw chuck. 5. Revolving centre 6. Tool post. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Head stock. 3. Tail stock Jaw chuck. 5. Revolving centre 6. Tool post. JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007

Saddle Name 3 component parts on the saddle of the lathe. 1. Head stock. 2. Cross slide. 3. Tail stock Jaw chuck. 5. Revolving centre JF 2007

Your answer is- WRONG Sorry try again just click on the arrow JF 2007