1 DemoSat Soldering DemoSat Training Boulder, Colorado December 7, 2002.

Slides:

Advertisements

Similar presentations

EMS1EP Lecture 3 Intro to Soldering Dr. Robert Ross.

Advertisements

AnaSonde Assembly. What is the AnaSonde? *Reads temperature, pressure, and humidity data from the atmosphere *After it is sent into the atmosphere, it.

Colorado Space Grant Consortium Gateway To Space ASEN / ASTR 2500 Class #06 Gateway To Space ASEN / ASTR 2500 Class #06.

Placing & Soldering Components Electronics 1 CVHS.

Soldering Basics. 2 Overview  Introduction Definition Equipment  Procedure Preparation Execution Finishing  Specific Techniques Desoldering Tinning.

Electrical Repair Soldering and Crimping By Fernando Martinez And Rudy.

Soldering 101 A Really HOT Topic. Soldering The process of making an electrical connection by melting low-temperature metal alloys around component leads.

Digital Electronics Soldering & De-soldering. 2 This presentation will… Review the tools needed to solder and de-solder electronic components. Demonstrate.

Lesson Objectives To learn how to solder components onto a circuit board safely and correctly. Success Criteria Must Be able to understand the health and.

Electronics Merit Badge Class 4 5/17/2015Electronics Merit Badge Class National Scout Jamboree1.

Soldering Basics. Ground rules for soldering Rule 1: Irons get hot. Be safe. Rule 2: You need to wet your sponge. This wet sponge is used to clean the.

Colorado Space Grant Consortium Gateway To Space ASEN / ASTR 2500 Class #06 Gateway To Space ASEN / ASTR 2500 Class #06.

1 Student Hands On Training I (2009) Soldering 101.

1 Chelmsford Amateur Radio Society Intermediate Licence Course Carl Thomson G3PEM Slide Set 12: v Jun-2007 (10) Soldering Chelmsford Amateur Radio.

Intermediate Course (10) Soldering Karl Davies East Kent Radio Society EKRS 1.

Surface Mount Device Soldering Materials by Linz Craig.

Colorado Space Grant Consortium Soldering 101. Caution: - Soldering is dangerous if not respected - Be mindful of where you are and where the soldering.

Basic Soldering Tips and Techniques! RM1B. Before starting the construction of a soldering project, be sure that your soldering iron tip is in good shape!

Electrical Current – flow of electrons

Soldering & The Tinning Process

SpectraSonde Assembly. What is the SpectraSonde? Reads temperature, pressure, and humidity data from the atmosphere. The SpectraSonde doesn’t fly like.

Introduction to Soldering

How To Solder By: Stephen Eibling.

Plated Through Hole Soldering Materials by Lindsay Craig.

PRACTICAL ELECTRONICS MASTERCLASS (Mr Bell) 1. Basic Electronic Components These components will be discussed further during the course, also have a look.

Soldering Safety – Soldering Irons are very HOT! Name: 1. When I am not using the soldering iron, I should return it to the holder because________ _________________________.

Soldering. Soldering Tools Soldering Iron Soldering Iron Care & Maintenance Tinning Process Good Solder Connections Bad Solder Connections De-Solder Process:

Introduction to Sensors - Part 1 Freshman Engineering Honors Program.

-Attaching metal with solder -Adhesion -Alloy of lead & tin- used in soft soldering- low melting point.

Sumo Robot. Materials Part NameQty 3-9 volt Motor2 Gear sets2 Wheels4 Axles 4 Base1 Straws2 Switches2 Bolts & Nuts4 Hook up wire15'

Printed Circuit Board (PCB) manufacture Learning outcomes: To work effectively, independently and in small groups. To understand the importance of personal.

AnaSonde-3M Assembly. What is the AnaSonde-3M? The AnaSonde-3M reads temperature, pressure and humidity data from the atmosphere. After the AnaSonde is.

Introduction to Soldering

Soldering Dennis Yuan Fall What is it for? Making good conductive contact between a component and the PCB Through-hole parts Surface mount parts.

ASSEMBLING THE PCB – V3.914 Hold the PCB as shown below.

SOLDERING is the process of bonding together two or more metal parts with a thin alloy or soldering lead. Soldering is accomplished by heating the metals.

Colorado Space Grant Consortium Gateway To Space ASEN / ASTR 2500 Class #06 Gateway To Space ASEN / ASTR 2500 Class #06.

Center for Advanced Research and Technology Electronics Technology Lab

ASSEMBLING THE PCB Have the PCB in front of you as shown. Make sure there are no copper tracks showing. This side is called the component side.

RobEn Workshop Circuits Basics & Hardware (2) 1. PCP It is an abbreviation for Printed Circuit Board. It is very useful in any electrical circuit application.

Oisture Tester How to Solder. Learning Objectives Understand the soldering process Practice soldering Continue with design ideas Produce an information.

Soldering Basics.

Soldering 101 I am Geordy. After high school I had a job doing board-level repair on CRT monitors back when they were still worth repairing. I ended up.

MODULE 6: Soldering SUMMER CHALLENGE Electrical Engineering: Smart Lighting Michael Rahaim, PhD Candidate Multimedia Communications Lab Boston University.

A Different Soldering Class “Surface Mount Soldering”

Continuity tester a handy tool for testing circuits

Soldering PCBs – Siren Kit Week 2 of 2

Introduction to Soldering

Soldering Magic of Electrons © 2011 Project Lead The Way, Inc.

Vocabulary Tinning Wetting Surface tension Flow.

Soldering PCBs – Siren Kit Week 1 of 2

Introduction to Soldering (PCB Bread boards)

Soldering Technique.

Wire Soldering 101.

Fault detection Lecture (1).

Electronics Soldering Basics

Student Hands On Training Workshop (SHOT 2007)

Soldering & The Tinning Process

Soldering & De-soldering

(Rhymes with Doddering)

Placing & Soldering Components

Testing the CheapBot-14 In six easy steps

Soldering & Desoldering

Be able to solder the capacitor and chip holder in place on the PCB.

Forging new generations of engineers

How to Solder Soldering must be learned from practice, it cannot be learned through bookwork Key factors affecting solder quality: Cleanliness Temperature.

Soldering: Methods, Tips, and Applications

By Gerry Crenshaw WD4BIS

Student Hands On Training Workshop (SHOT 2007)

Soldering & De-soldering

Presentation transcript:

1 DemoSat Soldering DemoSat Training Boulder, Colorado December 7, 2002

2 Soldering Circuit Board Resistor Solder Pads Side View Top View PCB – printed circuit boards

3 SolderingIron

4 Move soldering iron until tip is touching wire & solder pad

5 Move solder to touch edge of tip. Solder

6 Hold until solder melts on tip by wire Solder

7 Move solder back to touch wire only Solder

8 Move solder in to form a small pocket Solder

9 Move soldering iron tip up. This will drag solder up with it. Solder

10 Look for shinny fillets

11 Soldering Tips 1.Make sure tip is hot 2.Clean & tin tip 3.Keep tip clean by using wet sponge and cloth 4.Heat until the parts are hot enough to melt solder 5.Hold until solder flashes around pad 6.Do not put too much solder on

12 Top View Tinned Copper Traces

13 Top View Soldered Solder bridge shorting two traces - bad, bad, bad But, can be fixed by reheating or using solder sucker