Tutorial on Machine vice

Slides:



Advertisements
Similar presentations
Machining a V-Block Flexible Manufacturing Copyright © Texas Education Agency, All rights reserved. 1.
Advertisements

Group 3- Zach Hallowell (leader) Greg Rolph Mitch Miller Rob Sutton Mark Adrean.
A New Stripline Connection to JPARC Horn 1 Larry Bartoszek BARTOSZEK ENGINEERING 9/23/04.
EML 2023 – Modeling, Assemblies Lecture 3.2 – Assemblies, part 2.
SolidWorks Week 2-3.
1 Helpful Notes 2005 Tutorial 1 : Game Pad.
OBLIQUE VIEWS Oblique drawings provide a quick way to sketch an object and represent the three dimensions of height, width and depth. Oblique drawings.
Solidworks: Lesson 4 – Assembly Basics and Toolbox
Riveted Joints Hareesha N G Dept. of Aeronautical Engg Dayananda Sagar College of Engineering Bangalore-78 5/12/20151Hareesha N Gowda, DSCE, Blore-78.
Major Diameter: The largest diameter of the thread Minor Diameter: The smallest diameter of the thread Pitch: Distance between two threads (mm) or no of.
Geometry Control – Modifying and Relimiting; Using Axes and Transformation Ideas Chapter 2: 2.4 & 2.5 R. Lindeke IE 1225.
L.C. Technology ROBOT ASSEMBLY. Base Assembly BASE File off raised tabs on each side of Servo. Place Servo in vice between Fibre Clamps. Raised Tabs Repeat.
Projection of Points Hareesha N G Dept of Aeronautical Engg Dayananda Sagar College of Engg Bangalore-78 5/24/20151Hareesha N G, DSCE, Blore.
Copyright © Texas Education Agency, All rights reserved.
Solidworks Exercise Modeling the bearing block (40 minutes)
Threads and Fasteners.
Lathe.
Resource 2 Manufacturing Techniques Machining Operations & Techniques.
Isometric Projections
SolidWorks: Extruded Cuts, Fillets, and Patterns Introduction to Robotics.
SOLIDWORKS: Lesson III – Patterns & Mirrors
Dr. R. Ribeiro, Mechanical Engg. Dept. IITD
LAUNCHER BASE PARTS B A D E F C G. LAUNCHER BASE PARTS B A D E F C G.
Lesson No. 11 Week No. 07 Name of lesson Marking Tools
MACHINE TOOLS Dept. of Mech & Mfg. Engg..
Part and Drawing Dimensioning
Holes In AutoCAD Make a Slam Dunk.
2012 IDEA ASSEMBLY “HINT” PACK. ARM: draw in 2D Copy / paste this view into Inventor.
Solidworks Exercise Modeling the piston (30 minutes) Open a new part file and Save as Piston.sldprt Create the Cylinder Click on Top Plane (or plane 2)
1 Manufacturing Projects Flexible Manufacturing Copyright © Texas Education Agency, All rights reserved.
Mechanical Drawing (MDP 115)
TAIL STOCK ASSEMBLY Modeled & Compiled by R.Rajashekar Asst. Professor Department of Mechanical Engineering U.V.C.E, Bangalore-1.
Holes and Hole Notes Introduction to Engineering Design
The Lego Man Basic 3D Modelling. The Head Use the Revolve Tool to get the sketch from 2D to 3D.
Learning Objectives • Create sweep features. • Create lofted features.
Advanced Engineering Design and Presentation Wood Clamp Parametric Modeling Skill Builder Copyright © Texas Education Agency, All rights reserved.
Definitions and callouts
Tutorial on Plummer Block Hareesha N G Dept of Aeronautical Engg Dayananda Sagar College of Engg Bangalore-78 6/11/20161Hareesha N Gowda, DSCE, Blore-78.
Tutorial on Screw Jack Hareesha N G Dept of Aeronautical Engg Dayananda Sagar College of Engg Bangalore-78 6/11/20161Hareesha N Gowda, DSCE, Blore-78.
Camera Motion System Requirement Design Details FEA.
The Process of Making The Best CO2 Machine! Agricultural Mechanics / Woodshop Mr. Weaver The Process of Making The Best.
Shear force and bending moments in Beams
Mr P Mulholland AS Design and Technology St Joseph’s HS Crossmaglen
Flexible Manufacturing
Reading Drawings.
Screw Threads.
DRILLING Dept. of Mech & Mfg. Engg..
POINTS IN 3 DIMENSIONS 2D The xy-plane is used to plot points in 2D.
Metalwork Screw Threads.
Development of lateral Surfaces
Fasteners.
Section of Solids Hareesha N Gowda Lecturer
Development of Surfaces
Riveted Joints Hareesha N G Dept. of Aeronautical Engg
Alternate Views Introduction to Engineering Design
Holes and Hole Notes Introduction to Engineering Design
Technological Drawings
Subject Name: Dynamics of Machines Subject Code: 10AE53
Fastening devices.
EML 2023 – Threads and Fasteners
Holes and Hole Notes.
Holes and Hole Notes Introduction to Engineering Design
McMaster linear bearing #6709K180 with guide rail suppressed
Holes and Hole Notes.
EML 2023 – Threads and Fasteners
3D Modelling Workshop By Keith Phelan!.
Miniature Train Project
Holes and Hole Notes Introduction to Engineering Design
DRAWING A HELIX/SCREW THREAD
Presentation transcript:

Tutorial on Machine vice Hareesha N G Dept of Aeronautical Engg Dayananda Sagar College of Engg Bangalore-78 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Machine vice Assembly 4/20/2017 Hareesha N G, DSCE, Blore-78

Exploded view of machine vice 4/20/2017 Hareesha N G, DSCE, Blore-78

Exploded view of machine vice 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Part 1: Body Step 1:Protrusion Sketch on front plane or XZ plane as shown in fig Symmetric protrusion distance 100 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 2: Cut out Sketch on Top face or XY plane as shown in fig cut out depth 57 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 3: Protrusion Sketch on Bottom face or XY plane as shown in fig protrusion distance 23 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 4: Cut out Sketch on Top face or XY plane as shown in fig Cut out depth 23 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 5: Protrusion Sketch on Side face or YZ plane as shown in fig protrusion distance 5 mm Mirror the above feature to the other face 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 6: Cut out Sketch on Bottom face or XY plane as shown in fig Cut out depth 10 mm for rectangle 60 X 165 Cut out depth 13 mm for rectangle 52 X 165 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 7: Hole Create hole 1 of diameter 20 mm and depth 45 mm Create hole 2 of diameter 12 mm and depth 20 mm Create hole 3 of diameter 3 mm and depth 40 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Part 2: Movable Jaw Step 1:Protrusion Sketch on front plane or XZ plane as shown in fig Symmetric protrusion distance 100 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 2: Cut out Sketch on side face or YZ plane as shown in fig Cut out depth 50 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 3: Hole Create hole 1 of diameter 20 mm and depth 50 mm Create hole 2 of diameter 5 mm(2 holes deep 10 mm) Create hole 3 of diameter 5 mm(2 holes deep 10 mm) 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Part 3: Jaw Grip Sketch on Top plane or XY plane as shown in fig Symmetric protrusion distance 8 mm Create counter sink hole of diameter 6.3 mm, countersink dia of 12 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Part 4: Screw M6 Step 1: Revolved protrusion Sketch on front plane or XZ plane as shown in fig Use revolve protrusion angle 1800 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 2: Cut out Sketch on Top face or XY plane as shown in fig Use cut out depth of cut 1.9 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Part 5: Screw Rod Step 1: Revolved Protrusion Sketch on front plane or XZ plane as shown in fig Use revolve protrusion angle 1800 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Step 2: Cut out & Thread Sketch on Right plane or YZ plane as shown in fig Use symmetric cut out through all Create thread on cylindrical body 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Part 6: Washer Create sketch on top plane or XY plane as shown in fig Symmetric protrusion distance 3 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Part 7: Nut Create sketch on Top plane or XY plane as shown in fig Symmetric protrusion distance 8 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Part 8: Nut Create sketch on Top plane or XY plane as shown in fig Symmetric protrusion distance 5 mm 4/20/2017 Hareesha N G, DSCE, Blore-78

Hareesha N G, DSCE, Blore-78 Part 8: Clamping Plate Create sketch on Top plane or XY plane as shown in fig Symmetric protrusion distance 8 mm Create countersink hole of dia 6.3 mm and countersink dia 12 mm 4/20/2017 Hareesha N G, DSCE, Blore-78