Applied Technology High School ATE 1012 Grade 10 Eng. Rose Hasan.

Slides:

Advertisements

Similar presentations

EELE 461/561 – Digital System Design

Advertisements

1001ENG Engineering Practice and Sustainability Introduction to Electronics.

EMS1EP Lecture 3 Intro to Soldering Dr. Robert Ross.

BTEC First Engineering

BTEC First Engineering

Today’s Objectives: Soldering Soldering is non-trivial, especially surface mount components Soldering is non-trivial, especially surface mount components.

FIGURE B-1 Printed circuit board (PCB). (Courtesy of TRW/UTC Transformers.) Dale R. Patrick Electricity and Electronics: A Survey, 5e Copyright ©2002 by.

OVERMOLDING PROCESS & MATERIAL ELECTRONIC MODULE ASSEMBLIES

ELECTRONIC/COMPUTER AGE. Electronic/Computer Age  Electronics –Electrical signals can carry information quickly over wires or through the air by radio.

Printed Circuit Board Design

Learn-to-Solder Exercise: Practice Flasher Circuit AEM 1905: Spaceflight with Ballooning University of Minnesota.

ECE 404 PCB Design Presentation Jakia Afruz.  Printed Circuit Board  Electronic Board that connects circuit components  PCB populated with electronic.

Surface Mount Device Soldering Materials by Linz Craig.

Technology-Assisted Assessment Inquiry Part 1

PCB L AYOUT P LANNING AND D ESIGN. BLOCK DIAGRAM All electronic equipments can be considered as systems comprising a set of interacting elements responding.

Institute Of Applied Technology ATE 1012 Grade 10 Eng. Rose Hasan.

Overview Test Interface (TIU PCB‘s) are extremely expensive.

Introduction to Soldering

IEEE’s Hands on Practical Electronics (HOPE) Lesson 1: Introduction.

Plated Through Hole Soldering Materials by Lindsay Craig.

Ken YoussefiUC Berkeley 1 Electrical Drawings Ken YoussefiUC Berkeley 2 Types of Electronic Diagrams Schematic Diagrams Using graphic symbols, shows.

Making Printed Circuit Boards High Quality and Low Price (From the Bathroom Sink)

PRACTICAL ELECTRONICS MASTERCLASS (Mr Bell) 1. Basic Electronic Components These components will be discussed further during the course, also have a look.

2007 Electronic Project Kit Remote Control Nightlight Biological & Agricultural Engineering.

Setting up the Ricoh C305 Press F5 to start the Presentation

Printed Circuit Board (PCB) manufacture Learning outcomes: To work effectively, independently and in small groups. To understand the importance of personal.

ASCEND as a step towards a CubeSat. ASCEND program previously Oversized for their task No well defined goal Primitive electronics.

“PCB” -AMIT NIKAM -ASHI NAGARIYA.

Making a PCB Report and ppt – presentation 1.)Structure 1.1)Making the PCB 1.2)Assembling a circuit )The components I choose )They functions.

Operational Research (O.R.) case studies. What’s the problem?

Soldering & Brazing ALWAYS USE LEAD FREE SOLDER!!!!

IPC Thermal Transfer Components, which for thermal reasons require extensive surface contact with the board or with a heatsink mounted on the.

Basic Electrical Circuit Materials Colts Neck High School Applied Technology.

Institute Of Applied Technology ATE 1012 Grade 10 Eng. Rose Hasan.

IPC-2221 Connectors and Interconnects

Soldering iron By: Deepa Krishnaswamy. Problems - too many things to hold - iron, solder, and piece you’re working on - hard to see the piece properly.

PRACTICAL ELECTRONICS MASTERCLASS ASSEMBLY PRESENTATION (MR BELL) 1.

IPC Mounting Over Conductive Areas Metal-cased components shall be mounted insulated from adjacent electrically conductive elements. Insulation.

Center for Advanced Research and Technology Electronics Technology Lab

How to make a PCB.

Chapter 22 Electrical Systems. Textbook page 169, 171.

Electrical Engineering Grade 10 ST May Electricity Static electricity: the jumping of electrons from one object to another causes static electricity.

Making it at home. What is a PCB ?  A PCB contains a fiber glass epoxy board with thin copper layers attached to it.  A photographic process is used.

 A PCB is printed circuit board, also known as a printed wiring board. It is used in electronics to build electronic devices. A PCB serves 2 purposes.

Innovative products Innovative technologies. Business area.

PACKAGE FABRICATION TECHNOLOGY Submitted By: Prashant singh.

PCB Assembly. INTRODUCTION  PCB abbreviation is a printed circuit board,also known as a printed wiring board.  For electronics PCB is used to build.

SeaPerch Electrical System. Electrical System Overview Assemble the control box. Make the Cat5 connector. Wire the motors to the tether. Wire the control.

Soldering Basics.

Electroplating Applying metal to a conductive surface by David Clark.

MODULE 6: Soldering SUMMER CHALLENGE Electrical Engineering: Smart Lighting Michael Rahaim, PhD Candidate Multimedia Communications Lab Boston University.

SeaPerch Electrical System

Printed Circuit Boards Basics

ELECTRONIC CIRCUIT DESIGN & MANUFACTURE

Starter Look at the images below. What do you see? Write your answers on your mini white board.

FEE Electronics progress

Changed wiring of the 555 timer

Common termination methods:

पी.सी.बी बोर्ड.

Basic Skills Soldering Class

Making a simple steady hand game

Natural Sciences and Technology Grade 6

Circuits _____________ ______________

Manufacturing Processes

Electric Circuits.

SeaPerch Electrical System

Benefits & Advantages of Pogo Pins

Presentation transcript:

Applied Technology High School ATE 1012 Grade 10 Eng. Rose Hasan

 Learners who successfully complete this module will:  Identify soldering functions  Remove and replace components on printed circuit boards.  Identify the different accessories needed for soldering and desoldering.  Assemble, solder and test the electronic circuit using the developed PCB in the previous module Eng. Rose Hasan

 What is soldering/de-soldering?  Soldering is a quick and efficient method of joining metals permanently. Eng. Rose Hasan

 What is de-soldering?  However, de-soldering is a method of removing the solder and components from circuit boards. Eng. Rose Hasan

 Soldering is used for:  Providing mechanical support by attaching various electrical components to PCBs  Providing electrical contact between the component leads and conducting paths on the PCBs. Eng. Rose Hasan

 De-soldering is used for:  Troubleshooting PCBs  Repair purposes  Components replacement Eng. Rose Hasan

 mbly.html Eng. Rose Hasan

 Activity 1: Compare between soldering and de-soldering by completing the following table: (Page 8) Eng. Rose Hasan

 Cont. Module 6.  Activity 2: PCB drilling, mounting components and soldering. Eng. Rose Hasan