Making Printed Circuit Boards High Quality and Low Price (From the Bathroom Sink)

Slides:

Advertisements

Similar presentations

SMG facility – 24k Square Feet. Drilling We have 7 fully automated Excellon Drilling/ Routing machines. The drilling program is generated from the customer.

Advertisements

Preparing Printed Circuit Boards (PCBs) for Flight Computers AEM 1905, Fall 2008.

PCB fabrication/ Eagle Workshop #1

EELE 461/561 – Digital System Design

Instructions of making PCB by using Negative Film Resist

Manufacturing Processes for a 4 Layer Multi-layer PCB Section through PCB Via hole SMD Pad The following presentation covers the main processes during.

EMS1EP Lecture 3 Intro to Soldering Dr. Robert Ross.

BTEC First Engineering

The Little Buffer PCB C3 TIP GND R4 R3 R1 R3 R2 R6K J L +V 0V –V–V A D C E F A1 A3 H BRI03 TL071 C2C1.

CricketSat Assembly.

Produce Your Own PCB Board Jack Ou Engineering Science Sonoma State University.

PCB Design Presentation

One Way Circuits Limited Printed Circuit Board Manufacturer A Guide To Manufacturing Multilayer PCBs Use Left and Right Cursor keys to navigate ESC to.

PC Board Manufacturing Kate McDonnell & Cherelle Bishop CSU GK-12 Summer Planning 2011.

Printed Circuit Board Design

Homemade Printed Circuit Boards 6/22/2015 Jonathan Weaver, KM4FIK With special thanks to Paul (WA7ZVY)

ECE 404 PCB Design Presentation Jakia Afruz.  Printed Circuit Board  Electronic Board that connects circuit components  PCB populated with electronic.

PCB design and fabrication Lin Zhong ELEC424, Fall 2010.

Daniel Miller Joe Quesada Justine Lazo

(Printed Circuit Board) Presented By S.Muthumari

PRACTICAL ELECTRONICS MASTERCLASS (Mr Bell) (COMPUTERS REQUIRED FOR 1 ST PERIOD) 1.

Dr. Amr Talaat Abdulrahman Abdul-Munsif Information Engineering and Technology Electronics Department Microcomputer Applications.

RD51 22/11/2011 RD51 22/11/2011 Your PCB partner RD51 22/11/2011.

Ken YoussefiUC Berkeley 1 Electrical Drawings Ken YoussefiUC Berkeley 2 Types of Electronic Diagrams Schematic Diagrams Using graphic symbols, shows.

Machine Tools And Devices For Special Technologies Printed circuit manufacturing Slovak University of Technology Faculty of Material Science and Technology.

Applied Technology High School ATE 1012 Grade 10 Eng. Rose Hasan.

Home PCB fabrication 1-Tools 2-Procedure 3-Example.

A 555 TIMER PROJECT FOR KS3/4 DEVELOPED BY FOR

1 From logic to hardware Ellen Spertus MCS 111 November 25, 2003.

QRP Page 1 Toner Transfer Method for PCBs One ham’s first attempts to make PCBs at home Jim Larsen, AL7FS Ver 1.0 3/22/06 By.

PCB manufacturing PCBpro.com.

Suggestions:  Our class found that Yanka was Idea for creating PCB Board Layouts.  Yanka allows a user to print off a bill of materials. (It includes.

Printed Circuit Board (PCB) manufacture Learning outcomes: To work effectively, independently and in small groups. To understand the importance of personal.

A PCB has 2 signal layers, a split power layer and one ground layer. It also has two solder mask and two silkscreen layers. Is the board classified as:

“PCB” -AMIT NIKAM -ASHI NAGARIYA.

HKN Altium Workshop Basic Altium Workshop Friday, September 28th, 2007 HKN Brandon Gilles & Chris Mintle.

Making a PCB Report and ppt – presentation 1.)Structure 1.1)Making the PCB 1.2)Assembling a circuit )The components I choose )They functions.

Silk Screening.

WIRE REPAIR Chapter 4.

Photo lithography. Why? Add a photo sensitive layer ontop of a material. After treating with UV light, remove the affected areas. After processing (e.g.

IPC-D-325 Table 4-1 Typical Master Drawing Documentation Requirements

How to make a PCB.

PCB Design Overview Lecture 11

DIGITAL CLOCK Draw the schematic and the PCB.

Making it at home. What is a PCB ?  A PCB contains a fiber glass epoxy board with thin copper layers attached to it.  A photographic process is used.

Systems and Control - Electronics The Moisture Detector Tutor Group Name Date.

 A PCB is printed circuit board, also known as a printed wiring board. It is used in electronics to build electronic devices. A PCB serves 2 purposes.

To Panelize or Not to Panelize

Sensor Module v1.1. Step 1: Sand edges of PCB & drill bolt holes (3mm) Use small green power drill or pillar drill (as available) Goggles Use a piece.

Multi Tester Miss Begum. Bell Work Write down what you know about the following equipment / machinery: Pillar drill File Wet & dry paper Line bender Soldering.

Get a sheet at the corner of your table. Objective: You will define and apply various lettering styles in order to create a more challenging type set.

Workshop How to make a PCB

PPDM Association PPDM Lite Relational Model Version Note: Use this document for making printed copies of the diagrams, as it will provide better.

Mechatronics Putting It All Together A Quick Look Into PCB Design July 17, 2013.

Making Printed Circuit Boards Paul Kerchen i3 Detroit.

Printed Circuit Board Design

Solving Proportions Bingo

Designing Process Of Printed Circuit Boards

Daniel Miller Joe Quesada Justine Lazo

Basic Electronic Assembly and Test

ELECTRONIC CIRCUIT DESIGN & MANUFACTURE

Starter Look at the images below. What do you see? Write your answers on your mini white board.

a Printed Circuit Board

Changed wiring of the 555 timer

University of Wisconsin-Madison / SSEC

What determines impedance ?

testing and experimenting with electronic circuits

Bridge Challenge.

Computer-Aided Design (CAD)

Presentation transcript:

Making Printed Circuit Boards High Quality and Low Price (From the Bathroom Sink)

Ways to Make PCBs Tape and Etch Iron-on Resist Board House Ares Lite and Kepro Products

Ares Lite Unlimited number of holes when licensed Inexpensive, and with an education discount Pick and place components Draw traces Create ground plain Documentation in the top silk

D and L Pro (DALPro) Presensitized boards (4” by 6” and up) Developer (washing soda) Etchants (sodium persulfate) Carbide drill bits

To Build or Buy UV Table Foot Massager Photographic trays and beaker Zip lock bags Bug Light

The Process Design a PCB in Ares Lite Print paper copies Make a transparency (a UV mask) Expose PCB through the mask Develop Etch Strip Drill Solder!