SPX ITALIA – TECNOTEST division ECUREADER 4.50 - ENG Diagnostic 1|4 2008 By ATA

Summary Welcome Update from 4.40 to 4.50 Special Procedures Q & A

The Release 4.50

Cars – News of 4.50 BMW 3 SERIES E46 (98-04) Z4 SERIES E85 (07-..) BODY NETWORK ZKE BODY COMPUTER RAIN / LIGHTENING SENSOR RLS COMBINATION SWITCH MODULE KOSTAL LWS VISUAL./TELEMATICS ALPINE BM Z4 SERIES E85 (07-..) AIRBAG AUTOLIV SRS ACSM ENGINE MANAGEMENT SIEMENS DME MSS70

Cars – News of 4.50 BMW SERIE 5 E 60-61 (06-..) FUEL PUMP MANAGEMENT EKPS GEAR MANAGEMENT VTG RADIO/CD VDO CAR COMUNIC.CENT. RADIO/CD CON CONTROLLER COMBINATION SWITCH MODULE KOSTAL SZL2 VISUALISATION/TELEMATICS MOTOROLA TCU VISUALISATION/TELEMATICS VDO CENTRAL INFO DISPLAY HEADLIGHTS SETTING FLA

Cars – News of 4.50 BMW SERIE 7 E65 66 (02-) AIRBAG DELPHI SRS SASL - LEFT SIDE AIRBAG DELPHI SRS SASL - RIGHT SIDE AIRBAG DELPHI SRS SBSL - RIGHT SIDE AIRBAG DELPHI SRS SBSR - LEFT SIDE AIRBAG DELPHI SRS SFZ - MIDDLE SATELLITE AIRBAG DELPHI SRS SSH - DRIVE SIDE AIRBAG DELPHI SRS SSH - REAR SEATS AIRBAG LEAR SRS SSBF - PASSENGER SIDE AIRBAG SIEMENS SRS STVL - LEFT DOORS AIRBAG SIEMENS SRS STVL - RIGH DOORS ENGINE MANAGEMENT 745i BOSCH DME ENGINE MANAGEMENT 745i VDO VALVETRONIC ENGINE MANAGEMENT 745i VDO VALVETRONIC 2 PARKING AID VALEO PDC

Cars – News of 4.50 CHEVROLET CAPTIVA MATIZ (07-..) A/T AISIN A/T ELECTRIC CLUTCH TCCM PARKING AID PAS AIRBAG SDM MATIZ (07-..) ENGINE MANAGEMENT 1.0 L MPI

Cars – News of 4.50 CITROEN C2 C4 PICASSO ENGINE MANAGEMENT 1.1L (06..) SAGEM MPI J34P C4 PICASSO DRIVER SIDE DOOR ARVIN - MERITOR PASSENGER SIDE DOOR ARVIN - MERITOR WIPERS MANAGEMENT WIPERS

Cars – News of 4.50 CITROEN JUMPER 2 C3 RESTYLING SERVICE RESET MARELLI DASHBOARD C3 RESTYLING ENGINE MANAGEMENT 1.1L SAGEM MPI J34P

Cars – News of 4.50 FIAT 500 ’07 DOBLO’ 03 DUCATO ’06 BODY NETWORK DELPHI B.C. (PROXI Alignment) ENGINE MANAGEMENT 1.3 MULTIJET DPF MARELLI 6F3 C.R.EOBD CAN2 DOBLO’ 03 ENGINE MANAGEMENT 1.3 MULTIJET DPF MARELLI 6F3 CF3 Common Rail DUCATO ’06 SERVICE RESET MARELLI DASHBOARD

Cars – News of 4.50 FIAT IDEA PALIO RESTYLING ULYSSE ‘02 ENGINE MANAGEMENT 1.3 MULTIJET DPF MARELLI 6F3 CF3 Common Rail PALIO RESTYLING ULYSSE ‘02 DPF ADDITIVE MANAGEMENT MARELLI AIRBAG TEMIC AIRBAG

Cars – News of 4.50 FORD FIESTA ‘02 Focus ‘04 C-MAX ‘04 DASHBOARD INSTRUMENT CLUSTER ELECTRIC POWER STEERING EPS Focus ‘04 ENGINE MANAGEMENT 2.0 DPF PCM DURATECH ENGINE MANAGEMENT 2.0 PCM DURATECH C-MAX ‘04

Cars – News of 4.50 FORD NEW GALAXY (07-..) MONDEO ‘07 S-MAX ENGINE MANAGEMENT 2.0 PCM DURATECH MONDEO ‘07 ENGINE MANAGEMENT 2.0 TDCi DPF PCM DURATECH S-MAX

Cars – News of 4.50 FORD TOURNEO CONNECT (07-..) ABS+TRACT.CONTR. ABS ENGINE MANAGEMENT 1.8 TDCi PCM COMMON RAIL RADIO-CD AUDIO MODULE TRANSIT CONNECT (07-..)

Cars – News of 4.50 HOLDEN ASTRA AH CAPTIVA ENGINE MANAGEMENT CDTI (Z13DTH) MARELLI M.JET 603 Common Rail CAPTIVA PARKING AID PAS

Cars – News of 4.50 HONDA ACCORD CIVIC CR-V FR-V ENGINE MANAGEMENT 2.2 i-CDTI EDC Common Rail CIVIC CR-V FR-V

Cars – News of 4.50 KIA SORENTO (05-..) ELECTRONIC 4WD 4WD AIRBAG AIRBAG BODY NETWORK BODY COMPUTER ETACS CLIMA KLIMAUTOMATIK ABS+TRACT.CONTR. MANDO ABS

Cars – News of 4.50 LANCIA MUSA PHEDRA (07-..) Ypsilon ENGINE MANAGEMENT 1.3 MULTIJET DPF MARELLI 6F3 CF3 Common Rail PHEDRA (07-..) AIRBAG TEMIC AIRBAG Ypsilon ENGINE MANAGEMENT 1.3 MULTIJET DPF MARELLI 6F3 CF3 Common Rail

Cars – News of 4.50 LEXUS RX 300 (04-..) LEXUS RX 350 (04-..) ABS ABS AIRBAG AIRBAG DOOR LOCKING MASTER SWITCH BODY NETWORK BODY COMPUTER CLIMA CLIMA SUN ROOF SUNROOF IMMOBILIZER IMMOBILIZER LEFT – RIGHT MIRROR MIRRORS LEXUS RX 350 (04-..)                                      

Cars – News of 4.50 MERCEDES 171 SLK-CLASS 219 CLS-CLASS ABS+TRACT.CONTR. TEVES ABS+ESP AIRBAG TEMIC AIRBAG SRS 219 CLS-CLASS AIRBAG BOSCH SRS DASHBOARD VDO KI KOMBIINSTRUM. ENGINE MANAGEMENT CLS 500 BOSCH MOTRONIC ME 9.7

Cars – News of 4.50 NISSAN QASHQAI …….. ABS BOSCH ABS+TC AIRBAG AIRBAG SRS BODY NETWORK BATTERY SAVING BLINKING DOOR LOCKING HATCHBACK DOOR HEATED REAR WINDOW INTERNAL LIGHT MEMORY BUFFER BLINKER PTC HEATER REMOTE CONTROL BUZZER ……..

Cars – News of 4.50 NISSAN QASHQAI ENGINE MANAGEMENT 1.5 DCI SIEMENS EDC SID 301 Common Rail ELECTRIC POWER STEERING EPS IMMOBILIZER IMMOBILIZER Combination Switch MODULE CSM DASHBOARD IC CLIMA CLIMA

Cars – News of 4.50 OPEL ANTARA ASTRA-H AIRBAG SDM A/T AISIN A/T ELECTRIC CLUTCH. TCCM PARKING AID PAS ASTRA-H ENGINE MANAGEMENT 1.3 CDTI (Z13DTH) MARELLI M.JET 603 Common Rail

Cars – News of 4.50 OPEL SIGNUM MERIVA CORSA-D ENGINE MANAGEMENT 3.0 V6 CDTI (Y30DT) DENSO EDC COMMON RAIL MERIVA ENGINE MANAGEMENT 1.7 CDTI (Z17DTR) FAP EDC CORSA-D ENGINE MANAGEMENT 1.0 12v (Z10XEP) BOSCH MOTRONIC ME 7.6.X ENGINE MANAGEMENT 1.3 CDTI (Z13DTJ) MARELLI M.JET 603 Common Rail

Cars – News of 4.50 PEUGEOT BOXER (06-..) RENAULT MODUS DASHBOARD MARELLI DASHBOARD RENAULT MODUS SERVICE RESET (0507) SERVICE RESET

Cars – News of 4.50 SMART New fortwo (07-..) TOYOTA YARIS (07-) AIRBAG TRW SRS 31/34 TOYOTA YARIS (07-) ENGINE MANAGEMENT 1.4 D-4D DENSO

Cars – News of 4.50 VOLVO C30 (04-07) C70 (06-) ABS ATE BCM1 BRAKE CONTROL MODULE ABS ATE BCM2 BRAKE CONTROL MODULE ABS ATE BCM3 BRAKE CONTROL MODULE ENGINE MANAGEMENT 2.5 T BOSCH MOTRONIC ME9 STEERING WHEEL MANAGEMENT SWM1 STEERING WHEEL MODULE STEERING WHEEL MANAGEMENT SWM2 STEERING WHEEL MODULE C70 (06-) ABS ATE BCM2 BRAKE CONTROL MODULE ENGINE MANAGEMENT 2.5 T BOSCH MOTRONIC ME9 STEERING WHEEL MANAGEMENT SWM1 STEERING WHEEL MODULE

Cars – News of 4.50 VOLVO S40 S60 (01-) ABS (0407) ATE BCM1 BRAKE CONTROL MODULE ABS (0407) ATE BCM2 BRAKE CONTROL MODULE ABS (0407) ATE BCM3 BRAKE CONTROL MODULE ABS (99 00) ABS AIRBAG (99 ..) SRS AIRBAG DASHBOARD DIM DASHBOARD ENGINE MANAGEMENT 2.5 T (04 ..) BOSCH MOTRONIC ME9 ENGINE MANAGEMENT 2.5 T (99 ..) SIEMENS MPI EMS2000 TRACTION CONTROL (99 ..) DSA S60 (01-) RADIO/CD AUM Audio Module

Cars – News of 4.50 VOLVO V40 S70 (..-03) ENGINE MANAGEMENT Siemens MPI EMS2000 DASHBOARD DIM DASHBOARD AIRBAG (99..) SRS Airbag ABS (99..) ABS TRACTION CONTROL (99..) DSA STEEERING WHEEL MANAGEMENT SWM1 STEERING WHEEL MODULE STEEERING WHEEL MANAGEMENT SWM2 STEERING WHEEL MODULE S70 (..-03) AIRBAG SRS Airbag

Cars – News of 4.50 VOLVO S80 (00-..) V50 XC 90 RADIO/CD AUM AUDIO MODULE V50 ABS (0407) BCM1 BRAKE CONTROL MODULE ABS (0407) BCM2 BRAKE CONTROL MODULE ABS (0407) BCM3 BRAKE CONTROL MODULE STEERING WHEEL MANAGEMENT SWM1 STEERING WHEEL MODULE STEERING WHEEL MANAGEMENT SWM2 STEERING WHEEL MODULE ENGINE MANAGEMENT 2.5 T BOSCH MOTRONIC ME9 XC 90

Special procedures

Special procedures VW GROUP   Special procedures VW GROUP Lupo, Polo, Golf, Bora, New Beetle, Passat, Sharan (97-04) With this part of the software it is possible to set/code the ECU installed on vehicles, made by the VW group, specifically for models: Lupo, Polo, Golf, Bora, New Beetle, Passat e Sharan starting from model/year 1997 to 2004 - approx. This procedure can be carried out on new ECUs and as well as already coded ones (excluding AIRBAG and IMMOBILIZER) . The code inserted must always be at least 5 digits. Should the code be less, place in front of the code a sufficient number of zeros to reach 5 digits. E.g:- ECU code 65, insert 00065.

Special procedures VW GROUP ENGINE MANAGEMENT DPF REGENERATION   Special procedures VW GROUP ENGINE MANAGEMENT DPF REGENERATION This procedure allows the forcing of Diesel Particulate Filter regeneration, and must be performed if the DPF warning light is ON, (indicating a fault or low performance.). To carry this out, first check the fuel level (1/4 of the tank min.) and then just set off the function and follow the tool messages. Once the regeneration starts, the vehicle must be driven over 50 km/h (30 Mph) until the DPF warning lamp switches off. Regeneration is considered successful when the solid matter load is less than 15%.

Special procedures VW GROUP CAN SYSTEMS LOGIN PROCEDURE   VW GROUP CAN SYSTEMS LOGIN PROCEDURE The login operation permits access to some particular diagnostic procedures (e.g:- basic setting, channel 04) usually blocked by default (e.g:- steering wheel sensor calibration). Please refer to the original manufacturer’s documentation to obtain the proper login code.

Special procedures VW GROUP ENGINE MANAGEMENT   Special procedures VW GROUP ENGINE MANAGEMENT (NO CAN ENGINES WITH ELECTRIC THROTTLE BODY) EGR BASIC SETTING This operation allows adaptation of the EGR to the engine ECU. The values are stored in the ECU defining the EGR working range (min., max. and intermediate position). The procedure is necessary in case of component replacement or when the learnt values are erased. (e.g. should the electric throttle body basic setting prove difficult it can be avoided by erasing the learnt values).

Special procedures BMW E46 ABS-ESP STEERING WHEEL SENSOR CALIBRATION   Special procedures BMW E46 ABS-ESP STEERING WHEEL SENSOR CALIBRATION This function permits steering wheel sensor calibration. To achieve it, correctly carry out the following: Vehicle stationary and on a flat surface. Centrally align wheels and steering wheel Avoid placing loads on steering wheel Set off the procedure To check that the procedure has gone successfully, drive the vehicle at 30km/h (20mph) and steering fully left and right check if the steering returns to its original position (+/- 20 degrees).

Special procedures FIAT DOBLO’ (‘03) - IDEA ENGINE MANAGEMENT   Special procedures FIAT DOBLO’ (‘03) - IDEA ENGINE MANAGEMENT RAIL PRESSURE SENSOR REPLACEMENT The following procedure allows erasing the following learnt values in the ECU : “pilot injection” correction (linked to injectors ageing) MAIN injection correction (linked to 02 sensor signal).

Special procedures FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT   Special procedures FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT EXHAUSTS DIFFERENTIAL PRESSURE FEEDBACK SENSOR REPLACEMENT This procedure allows updating the self-adapting parameters relative to the exhausts differential pressure feedback sensor. The above is necessary when the sensor needs to be replaced. CAREFUL! Once procedure has been completed switch ignition off and wait at least 40 seconds for POWER LATCH completion (data will be erased and new values written in the ECU ).

Special procedures FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT   Special procedures FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT O2 SENSOR REPLACEMENT This procedure allows erasing the learnt values of the fuel quantity correction relative to the O2 sensor signal. This is required every time a component needs to be replaced.

Special procedures FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT   FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT CRANKSHAFT TOOTHED WHEEL/RPM SENSOR REPLACEMENT This procedure permits learnt values relative to the RPM signal. This is necessary every time a crankshaft toothed wheel/sensor is replaced. CAREFUL! Once procedure has been completed switch ignition off and wait at least 40 seconds for POWER LATCH completion (data will be erased and new values written in the ECU ).

Special procedures FIAT DOBLO’ (03) – IDEA ENGINE MANAGEMENT   Special procedures FIAT DOBLO’ (03) – IDEA ENGINE MANAGEMENT PRE-CATALYZER REPLACEMENT PARTICLE FILTER REPLACEMENT The following procedures allow updating the stored parameters relative to: pre-catalyzer ageing number of unfinished regenerations This is necessary if the above components are replaced in vehicles fitted with DPF (Diesel Particulate Filter).

Special procedures FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT   Special procedures FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT PARTICLE FILTER REGENERATION This procedure allows forced particle filter regeneration and must be carried out if the warning light is on (indicating a fault or low performance). Check if the motor is at a temperature higher than 70°C, and follow the instructions once the operation has been set off. WATCH OUT!! This operation causes higher temperatures at the exhaust pipe. During the above operation, do not leave the vehicle parked on highly inflammable surfaces (e.g. dried grass, oily floors or fuel residuals, etc).

Special procedures FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT   Special procedures FIAT DOBLO’ (03) - IDEA ENGINE MANAGEMENT OIL CHANGE The following procedure allows updating the ECU parameters of the oil engine quality in vehicles equipped with DPF. CAREFUL! Once procedure has been completed switch ignition off and wait at least 40 seconds for POWER LATCH completion (data will be erased and new values written in the ECU ).

Special procedures FIAT DOBLO’ ‘06 DASHBOARD   Special procedures FIAT DOBLO’ ‘06 DASHBOARD HEADLIGHTS LEVELLING SYSTEM The following procedure calibrates the beam height at the positions 0,1,2,3 inserted on the dash. Proceed as follows: Park vehicle on flat ground. Set the headlights position to “0” on the dash. Set the required headlight level using the tool.

Special procedures FIAT DOBLO’ ’06 DASHBOARD DASHBOARD DASHBOARD   Special procedures FIAT DOBLO’ ’06 DASHBOARD SAFETY BELT ALARM DISABLING The following procedure disables the alarm for unattached safety belts. DASHBOARD SAFETY BELT ALARM ENABLING This following operation enables the alarm for unattached safety belts. DASHBOARD ODOMETER RESET This procedure erases the total driven Km/miles value (only for values under 200 Km/125 miles).

Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT   Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT SELF-ADAPTATION RESET Should some components need replacing such as idle actuator, 02 sensor, knock sensor, this function resets the learnt values to the factory defaults to manage correctly the new component.

Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT ECU CODING   Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT ECU CODING The following function is required in case of ECU replacement and also allows storage of the injector codes. Procedure: Insert driven kilometers/miles. 6 digits must be inserted; e.g. to show a journey of 3000 Km (1800miles), digit 003000. 2) Insert injector codes installed on each cylinder. CAREFULLY follow the tool instructions during the procedure.

Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT INJECTORS CODING   Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT INJECTORS CODING This operation allows storing in the ECU each individual’s cylinder injector code in case of replacement. In this way, the ECU can manage at its best the injection time according to the new injectors. Generally the codes are supplied with the injectors and in any case are printed on each body.

Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT   Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT CRANKSHAFT TOOTHED WHEEL/RPM SENSOR REPLACEMENT This procedure permits learnt values relative to the RPM signal. This is necessary every time a crankshaft toothed wheel/sensor is replaced. CAREFUL! Once procedure has been completed switch ignition off and wait at least 40 seconds for POWER LATCH completion (data will be erased and new values written in the ECU ).

Special procedures FIAT 500 ’07 ENGINE MANAGEMENT   FIAT 500 ’07 ENGINE MANAGEMENT OIL QUALITY (ONLY VEHICLES WITH DPF) The following procedure allows updating the ECU parameters of the oil engine quality in vehicles equipped with DPF. ENGINE MANAGEMENT PRE-CATALYZER REPLACEMENT (ONLY VEHICLES WITH DPF) This procedure permits updating the ECU parameters relative to the pre-catalyzer ageing and the number of uncompleted regenerations. This is necessary in case of pre-catalyzer replacement .

Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT   Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT MAF SENSOR REPLACEMENT The following procedure allows component adaptation in case of its replacement. To complete the operation, follow carefully the tool instructions. ENGINE MANAGEMENT O2 SENSOR REPLACEMENT This procedure allows erasing the learnt values of the fuel quantity correction relative to the O2 sensor signal. This is required every time a component needs to be replaced.

Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT   Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT EXHAUSTS DIFFERENTIAL PRESSURE FEEDBACK SENSOR REPLACEMENT This procedure allows updating the self-adapting parameters relative to the exhausts differential pressure feedback sensor. The above is necessary when the sensor needs to be replaced. CAREFUL! Once procedure has been completed switch ignition off and wait at least 40 seconds for POWER LATCH completion (data will be erased and new values written in the ECU ).

Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT   Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT RAIL PRESSURE SENSOR REPLACEMENT The following procedure allows erasing the following learnt values in the ECU : “pilot injection” correction (linked to injectors ageing) MAIN injection correction (linked to 02 sensor signal).

Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT   Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT PARTICLE FILTER REGENERATION This procedure allows forced particle filter regeneration and must be carried out if the warning light is on (this means a fault or a reduction in efficiency). Check if the motor is at a temperature higher than 70°C, and follow the instructions once the operation has been set off. WATCH OUT!! This procedure causes higher temperatures at the exhaust pipe. During the above operation, do not leave the vehicle parked on highly inflammable surfaces (e.g. dried grass, oily floors or fuel residuals, etc).

Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT   Special procedures FIAT 500 ‘07 ENGINE MANAGEMENT PARTICLE FILTER REPLACEMENT The following procedures allow updating the learnt values relative to: components ageing number of incomplete regenerations This is necessary if the above component is replaced.

Special procedures FIAT DUCATO ‘06 DASHBOARD SERVICE RESET   Special procedures FIAT DUCATO ‘06 DASHBOARD SERVICE RESET This function allows resetting back to the factory default the dashboard maintenance indicator.

Special procedures OPEL CORSA-D ENGINE MANAGEMENT 1.3 75 CV   Special procedures OPEL CORSA-D ENGINE MANAGEMENT 1.3 75 CV HIGH SPEED CAN BUS PROGRAMMING Should the above ECU need to be replaced or high speed CAN-BUS network need re-configuration, this function allows to store in the the new ECU, the presence or not of other various ECUs (body, chassis, network etc.) installed on the car. A list of systems will appear and the operator must choose between “yes” or “no” related to the installed ones.

Special procedures OPEL CORSA-D ENGINE MANAGEMENT Z13DTJ - Z10XEP   Special procedures OPEL CORSA-D ENGINE MANAGEMENT Z13DTJ - Z10XEP VIN NUMBER CODING Through this operation the chassis ID number (VIN) will be written in the engine ECU. The VIN will be written in two steps: the first 9 characters after validation, the remaining 8. This procedure is required for good work performance and for the conformance to existing European laws.

Special procedures OPEL CORSA-D ENGINE MANAGEMENT Z10XEP   Special procedures OPEL CORSA-D ENGINE MANAGEMENT Z10XEP HIGH SPEED CAN BUS PROGRAMMING Should the above ECU need to be replaced or high speed CAN-BUS network need re-configuration, this function permits setting in the new ECU, the presence or not of other various ECUs (body, chassis, network etc.) installed on the car. A list of systems will appear and the operator must choose between “yes” or “no” related to the installed ones.

Special procedures OPEL ASTRA H 1.3 CDTI 90 cv   Special procedures OPEL ASTRA H 1.3 CDTI 90 cv ENGINE MANAGEMENT 1.3 CDTI 90 HP HIGH SPEED CAN BUS PROGRAMMING Should the above ECU need to be replaced or high speed CAN-BUS network need re-configuration, this function permits setting in the new ECU, the presence or not of other various ECUs (body, chassis, network etc.) installed on the car. A list of systems will appear and the operator must choose between “yes” or “no” related to the installed ones.

Special procedures OPEL ASTRA H ENGINE MANAGEMENT 1.3 CDTI 90 HP   Special procedures OPEL ASTRA H ENGINE MANAGEMENT 1.3 CDTI 90 HP INJECTOR CODING This procedure writes in the ECU the relative code to one or more injectors, associating each injector to the specific cylinder. Once the procedure is set off, it asks to which cylinder to assign the injector code. After having selected the cylinder ID (1-4), the stored code is shown; just insert the new one and confirm. Should this process be required for more than one or for all cylinders, repeat the above procedure every time is necessary.

Cars – News of 4.50 PEUGEOT 307 Restyling ENGINE MANAGEMENT 1.6 HDI FAP EGR WORKING RANGE SETTINGS The function allows to set and store automatically the EGR valve working range. The ECU will actuate the EGR reading the min & max position’s value, storing each one as well as LEARNT value. Warning: To complete the procedure, please mind to switch the ignition off and wait until “Power Latch” * will be stopped * Power Latch = Delay on main power supply shutdown

Special procedures NISSAN QASHQAI BMC – LIGHTS DEVIATION   Special procedures NISSAN QASHQAI BMC – LIGHTS DEVIATION HEADLIGHTS TIMING DELAY This function allows setting, choosing between the following default configurations of the headlights time. The operating modes are as follows: Mode 1 Mode 2

Special procedures NISSAN QASHQAI BMC – WINDSCREEN WIPERS   Special procedures NISSAN QASHQAI BMC – WINDSCREEN WIPERS WINDSCREEN WIPER SPEED The procedure allows enabling/disabling of the windscreen wiper speed variation in relation to the vehicle speed.

Q & A