Dynamic Propeller Balancing.

Slides:



Advertisements
Similar presentations
1. Instrument Clusters Theory Support Automotive – Displays & Accessories 1 of 13 Instrument Clusters Topics covered in this presentation: Analog Instrument.
Advertisements

CHAPTER 45 Engine Lubrication.
Vibration Analysis (cont)
 Without reference, identify principles relating to Fixed Radiological X-RAY PM with at least 70 percent accuracy.
InnoSys Process Sequence. End Effector Components End Effector Prox Switch Load Cell Wire Conduit Crows Foot Nut Runner.
Propeller Balancing Using the Model 1015 ProBalancer Sport
Control on the ground ATC Chapter 2 & 3.
FHM TRAINING TOOLS This training presentation is part of FHM’s commitment to creating and keeping safe workplaces. Be sure to check out all the training.
Heavy-Duty Truck Axle Service and Repair
Propulsion Train & Shaft Line Components
Tool removed during cycle Fault #2 Conditions for setting Tool cocked prox switch goes open during cycle AND force on load cell drops below limit in fault.
Basic Vibration Analysis
Presented by Skip Seila FAASTeam Lead Rep.
Vibration Sensors for Cooling Towers Challenges Cooling towers offer the vibration analyst many challenges in sensor selection, mounting and environmental.
1 Cranes Module 13. 2Objectives After this module you should be able to – identify the most common crane hazards – take the necessary steps to avoid those.
Chapter 3 Basic Vehicle Control
Mechanical Vibrations
NorCal Tech 2005 Technical Conference
Mechanical Vibrations
U U 1 Excitation of Structural Resonance Due to a Bearing Failure Robert A. Leishear David B. Stefanko Jerald D. Newton IMECE 2007 ASME, International.
Typical Steps of field Balancing Illustration with model 907
Charging System Service
Sling Safety.
Driveline Vibration and Service
Vibration & Temperature Sensor. Contents ■ Why monitor vibration? ■ Monitor a wide range of machines ■ Vibration measurements ■ Set alarm levels ■ Mounting.
Lease Automatic Custody Transfer
Rotor Track and Balance
Propeller Care & Maintenance for the Amphibian
Module 11: Use and Care of Equipment At the HIV Rapid Testing Site.
Purpose Power lines Equipment Assured Grounding GFCI Conclusion.
Chapter 9 Cranking Systems.
8 th Grade Physical Science. Force and Motion  Speed is how fast an object is moving.  Speed =  You can also use this formula to find the distance.
Pressure and Speed Limits
Motor Testing (Motor Only)
Settings & Adjustments. Settings & Adjustments.
Setting up the Ricoh C305 Press F5 to start the Presentation
Prepared by: Marimuthu Gurusamy Combined vibration analysis (velocity and acceleration envelope) for Prediction of rotating equipment (with rolling element.
LASER AND ADVANCES IN METROLOGY
Basic Vehicle Operation
Balancer Operation Intelift Operation Installation Troubleshooting Preventive Maintenance Preventive Maintenance OVERVIEW.
Flat Saw Training. Flat Saw Sizes –Low Horsepower Blade diameters range from 8” (200mm) to 18” (450mm) Power ranges from 4 to 25 horsepower.
Robot sensors MVRT 2010 – 2011 season. Analog versus Digital Analog Goes from 0 to 254 Numerous values Similar to making waves because there are not sudden.
Automotive Steering, Suspension and Alignment, 5/e By James D. Halderman Copyright © 2010, 2008, 2004, 2000, 1995 Pearson Education, Inc., Upper Saddle.
POWER TOOLS Electric drills
9 Drive Shafts and CV Joints.
Driver’s Education Chapter 3 Basic Vehicle Control.
Tool Removed During Cycle Fault #2 Conditions for Setting Tool cocked prox switch goes open during cycle AND force on load cell drops below 5 lbs. Active.
By the Brown Team Module 2. Driver Preparation Procedures Always check for small children and pets, fluid leaks, tire inflation, obvious physical damage,
The complete flow monitoring solution Measure – Display – Switch – Transmit.
Blocking a b c d.
Dynamic Propeller Balancing 06/06/2011 #1. Goals for This Seminar QUnderstand Basics of Vibration QUnderstand the Benefits of Balancing QUnderstand Fundamentals.
Basic Vibration Analysis ACES Systems/TEC Aviation Division 06/06/2011 #1.
ENM208 INTRODUCTION to MACHINING ANADOLU UNİVERSITY Industrial Engineering Department.
MIGHTY AUTOMATIC MIGHTY AUTOMATIC BELT TENSIONERS.
Fan Trim Balance Mike Lucas ACES Systems/TEC Aviation Division 06/06/2011 #1.
National Highway Institute 5-1 REV-2, JAN 2006 EQUIPMENT FACTORS AFFECTING INERTIAL PROFILER MEASUREMENTS BLOCK 5.
Piston Engine Propulsion Ignition. Ignition in a piston engine requires: Spark plugs Magneto Condensers Distributor Contact breakers electronic systems.
CNC FEED DRIVES.
Teknologi Dan Rekayasa
Rotor Track and Balance
Mechanical Vibrations
Forces on an Aircraft Four forces on an aircraft in flight:
Chapter 3 Basic Vehicle Control
OBJECTIVES Explain the factors that cause rotor damage.
OBJECTIVES Discuss how to diagnose problems with disc brakes.
FIGURE 20.1 Many vehicles, especially those equipped with four-cylinder engines, use a dampener weight attached to the exhaust system or differential,
Tool removed during cycle Fault #2
SYSTEMS FOR AIRCRAFT PREDICTIVE MAINTENANCE
Dynamic Propeller Balancing
Manual Drivetrains and Axles
Presentation transcript:

Dynamic Propeller Balancing

Goals for This Seminar Understand Basics of Vibration Understand the Benefits of Balancing Understand Fundamentals of Dynamic Propeller Balancing

Overview The Basics of Vibration Definition Why it happens How it is measured How we correct it

Overview Understanding the Benefits of Balancing Reduces the negative effects of vibration Increases service life and economy of operation

Overview Understanding the Fundamentals of Propeller Balancing Required equipment Setting up the equipment Data collection and processing The balancing process Avoiding the pitfalls

Basics of Vibration

The Basics of Vibration Definition For the purpose of Propeller Balance, vibration can be described as: “the unwanted, unproductive, cyclic oscillation of the propeller and engine assembly about its rotational axis.” For the purpose of Propeller Balance, vibration can be described as the unwanted, unproductive, cyclic oscillation of the propeller and engine assembly about its rotational axis.

The Basics of Vibration Remember All noise and/or vibration is not generated by an imbalance in the propeller. To verify the vibration source, a vibration survey should be conducted and manufacturers’ limitations adhered to. It is important to remember that all noise, and/or vibration is not generated by an imbalance in the propeller. To verify the vibration source, a vibration survey should be conducted and manufacturers limitations adhered to.

The Basics of Vibration Why Does It Happen? When the weight of a rotating propeller and engine assembly is not equally distributed, the dominant or heavy point attempts to continue moving in a straight line. The resulting force attempts to pull the assembly outside its rotational axis. The assembly then orbits what would be the normal center of rotation, causing vibration.

The Basics of Vibration Vibration-Related Complaints Passenger complaints of noise in the cabin Cracked exhaust stacks and sheet metal Higher than normal occurrence of engine and prop oil leaks and light bulb failures Physical movement of airframe (buzz in the seat, yoke, rudder pedals) Malfunctioning or failed avionics

The Basics of Vibration Examples of the Effects of Vibration Vibration excites natural frequencies in other components throughout the airframe and engine assemblies. The expended energy from vibration causes wear of components, reduced performance, passenger discomfort.

The Basics of Vibration How It Is Measured The vibration sensor generates a small voltage when the mass compresses the piezoelectric element. That voltage is proportional to the force being exerted on the element.

The Basics of Vibration How It Is Measured Sensor Types Sensor Engineering Units (EUs) Characteristics of Different Sensor Types Sensor Specifications Sensor Mounting

The Basics of Vibration How It Is Measured Sensor Types Displacement - Measures physical change of position. Velocity - Measures the rate of change of displacement with time. Acceleration - Measures the rate of change of velocity with time.

The Basics of Vibration How It Is Measured Engineering Units Mils (0.001 inches) - displacement IPS (Inches Per Second) - velocity gs (equivalent gravities) - acceleration

The Basics of Vibration How It Is Measured Sensor Characteristics Accelerometers Measure Acceleration Typically Reported in g’s More Sensitive to Higher Frequencies Directly Related to Force Caused by Unbalance Used in Balancing (after conversion to velocity or displacement)

The Basics of Vibration How It Is Measured Sensor Characteristics Velocimeters/Velometers Measure Velocity Typically Reported in IPS Peak More Sensitive to Medium Frequencies Directly Related to Energy from Unbalance Often Used in Balance

The Basics of Vibration How It Is Measured Sensor Characteristics Displacement Sensor Measure Change in Position Typically Reported in mils (1,000 of an inch) Peak to Peak More Sensitive to Low Frequencies Directly Related to Movements Due to Unbalance Seldom Used in Balance. (However, Displacement Units are Often Used)

The Basics of Vibration How It Is Measured

The Basics of Vibration How We Correct It Improve manufacturing methods Remove and replace Static Balance Static Balance + Dynamic Balance

Review The Basics of Vibration Definition Why it happens How it is measured How we correct it

The Benefits of Balancing Reduces: Noise Vibration Airframe damage Avionics damage Fatigue and stress on passengers Increases: Economy of operation Service life of airframe and components Comfort

The Benefits of Balancing Review Reduces the negative effects of vibration Increases service life and economy of operation.

Fundamentals of Balancing

Fundamentals of Balancing Equipment Required A device to collect vibration and phase data. A phase angle /speed sensing device A vibration sensing device Accessories: Cables, balance weights, hand tools.

Fundamentals of Balancing Equipment Required Approved reference Airframe manual Propeller Manual Engine manual (in some cases) FAA-approved “Guide to Propeller Balancing”

Fundamentals of Balancing Equipment Required Make sure the approval letter is attached to the Guide and references the material being used (document number, date, revision, and change numbers if applicable.)

Fundamentals of Balancing Setting Up the Equipment Always attach the vibration sensor as near as possible to the forward most point of the engine supporting the prop shaft. The base of the sensor should always point to the center of the prop shaft. The vibration sensor should not be in line with a cylinder and should be positioned at 12:00 or 6:00 whenever possible.

Fundamentals of Balancing Setting Up the Equipment If using a Phototach, attach it so as to be between 12 and 18 inches from the surface of the target blade and not perpendicular (90 degrees) to the surface of the blade. A 5 degree offset is best. The reflective tape should be 3M brand 7610, and not less than 1 inch wide. It should be installed no more than 14 inches out the prop blade from the center of the prop shaft.

Fundamentals of Balancing Setting Up the Equipment Cables should be routed away from electrical and high temp components. Attach with wire ties or tape to prevent excessive movement and possible damage. Do not close windows or doors on the cables as this may pinch or cut them. Make sure connections at the analyzer are secure.

Fundamentals of Balancing Setting Up the Equipment If using an onboard vibration monitoring system, synchrophaser or other signal sources, make sure you know the sensitivity and voltage outputs of the system. Always obtain your interface cables for these onboard applications from a qualified source.

Fundamentals of Balancing Setting Up the Equipment

Fundamentals of Balancing Data Collection & Processing The vibration sensor is installed on the engine as near the front bearing as possible. The Phototach is mounted on the cowling, behind the propeller. The reflective tape is applied to the back side of the target propeller blade in line with the Phototach beam. The mass is located by the relative occurrence of tach trigger and mass passage at the radial sensor location.

Fundamentals of Balancing Data Collection & Processing As the heavy spot on the propeller passes the location of the vibration sensor, the sensor generates and sends an electrical pulse to the analyzer. The Reflective tape triggers a response as it passes the Phototach, which then sends an electrical signal to the analyzer.

Fundamentals of Balancing Data Collection & Processing In this illustration, the vibration sensor and Phototach beam are co- located at the 12:00 or 0 degree position. Rotation is clock-wise from the viewers position. This is our starting point, elapsed time = 0

Fundamentals of Balancing Data Collection & Processing The speed is 1 RPM. Fifteen seconds (90 degrees) of travel has occured. In this sequence, the reflective tape has just entered the Phototach beam to trigger the tach event. Elapsed time = 15 seconds.

Fundamentals of Balancing Data Collection & Processing In this sequence, the mass (heavy spot) is passing the accelerometer position, 15 seconds (90 degrees) after the tape passed the Phototach beam. Elapsed time = 30 seconds (180 degrees of travel).

Fundamentals of Balancing Data Collection & Processing The tape and mass have both passed the 0 degree location. The unit now waits for the exact sequence to repeat for averaging. Elapsed time = 45 seconds (270 degrees of travel)

Fundamentals of Balancing Data Collection & Processing The process is repeated while the analyzer averages out errors caused by momentary vibration events outside the running average.

Fundamentals of Balancing Data Collection & Processing When sufficient data has been collected, the process is stopped by the operator and the averaged data displayed on screen. Notice that you have the option to Retake the data if desired.

Fundamentals of Balancing Data Collection & Processing A solution is then provided by the instrument based on a stored influence coefficient or a calculated test weight. If required, the process is then repeated for refinement of the solution.

Fundamentals of Balancing The Balancing Process Propeller Inspection Prior to Balancing Insure all Airworthiness Directives have been complied with for the propeller you are going to balance. Determine if there is a balancing procedure published by the airframe, engine or propeller manufacturer; if there is, it will take precedence.

Fundamentals of Balancing The Balancing Process Inspect the propeller blades for damage, nicks etc. refer to FAA Advisory Circular 20-37D which outlines care of metal propellers, and to applicable propeller manufacturers maintenance requirements. If balancing composite propeller blades, refer to the propeller manufacturer's procedures for repair of the propeller. Inspect propeller assembly for proper installation and security.

Fundamentals of Balancing The Balancing Process WARNING Perform a visual inspection of the spinner and spinner bulkhead for cracks, stop drills and welding. Mass trim weights MUST NOT be attached to a part with any of these conditions. To prevent an excessive number of weights from being attached to the spinner, remove any mass trim weights attached from previous dynamic balance jobs.

Fundamentals of Balancing The Balancing Process WARNING Static balance weight attached to the propeller hub by a certified propeller shop MUST NOT be removed.

Fundamentals of Balancing The Balancing Process With the equipment installed and all previously installed trim weights removed, head the airplane into the wind (10 kts maximum) and begin the data collection.

Fundamentals of Balancing The Balancing Process On run 1, allow the analyzer to collect and average data until the bars in the scale stop converging on the center. This should take between ten and thirty seconds under ideal conditions.

Fundamentals of Balancing The Balancing Process When the ENTER key is pressed to stop data collection, the Review Job screen shows the averaged amplitude and the phase angle of the out of balance condition.

Fundamentals of Balancing The Balancing Process REMOVE the previously installed trim weights before installing the new. Enter the “Actual Weight Installed” as near as possible to what you weighed and at the angle measured.

Fundamentals of Balancing The Balancing Process Where to place the weights Test weights can be placed under the spinner retention screws. It may be necessary to use longer screws for the test weights. If doing so, account for the delta between the normal and the longer screw. Be sure you are measuring the angles in relation to the sensor or tape as you specified in the setup being used.

Fundamentals of Balancing The Balancing Process Permanent weights may be installed under the flange or on the bulkhead. If installed under the flange, offset from spinner attaching screws by four times the diameter of the spinner screws.

Correction Calculation Diameter of spinner divided by 2 = radius of spinner (ex: 14 / 2 = 7.0”) Minus distance from test weight to permanent weight = permanent weight radius (ex: 7.0 - 1.5 = 5.5”) Required weight to balance x radius of spinner = net effect (ex: 25 g x 7.0 = 175 Gram inches) Divide by permanent weight radius = permanent weight (ex: 175 / 5.5 = 31.8 grams)

Fundamentals of Balancing Avoiding the Pitfalls If you remove the spinner in order to remove previously installed trim weights, index it and make sure it is always reinstalled by the index mark. Check inside the spinner for foreign objects, excess grease and trapped water.

Fundamentals of Balancing Avoiding the Pitfalls Unstable or erratic RPM readings on the analyzer are most commonly caused by: Angle of the Phototach relative to the tape. Phototach outside the 18 inch maximum or inside the 12 inch minimum distance. Tape too narrow for the velocity of the prop. Dirty or misaligned tape. Defective Phototach or Cable.

Fundamentals of Balancing Avoiding the Pitfalls Unstable or erratic vibration amplitude readings on the analyzer are most commonly caused by: Damaged or inoperative sensor Pinched, Cut, or shorted cable Unstable tachometer input. Mechanical defects of the assembly being balanced.

Fundamentals of Balancing Avoiding the Pitfalls You may also adjust the Phototach gain. Remove the screw holding the clear plastic cover on the aft end of the unit.

Fundamentals of Balancing Avoiding the Pitfalls The gain adjustment is the brass screw at the right. Make adjustment in a controlled environment such as with a bench grinder in a shop.

Fundamentals of Balancing Avoiding the Pitfalls Adjust the speed of the prop as closely as possible to the exact target RPM on EVERY run. A change in RPM will change the influence of an attached weight. Subsequent solutions will not have the same calculated results at different speeds.

Fundamentals of Balancing Avoiding the Pitfalls If an established influence for the engine and prop combination being balanced is not being used, the first weight the analyzer will ask you to install is a TEST weight. This weight may cause the vibration amplitude to increase. The intention of the test weight is only to induce a measurable change, not necessarily reduce the vibration.

Fundamentals of Balancing Avoiding the Pitfalls If the suggested TEST weight is greater than your experience tells you is necessary to induce a change, reduce the weight and enter the exact amount and angle of attachment into the analyzer. Remember that the amplitude may actually go up. This is not a malfunction of the equipment. Continue the balance process.

Fundamentals of Balancing Avoiding the Pitfalls There is no difference in the propeller balance procedure for a radial engine, opposed engine, turboprop, geared, variable pitch, or fixed pitch propeller.

Fundamentals of Balancing Avoiding the Pitfalls The “% error” is reduced very rapidly if the margin for error is large, (i.e. Higher amplitudes). As these amplitudes are reduced through the balancing process, that margin is greatly reduced and the “% error” may average down very slowly and may actually stall at some point. This is not a malfunction and is not a reason for concern.

Fundamentals of Balancing Avoiding the Pitfalls A variety of mechanical problems can show up at propeller turning speed these include Propeller out of track. Crankshaft unbalance. Bearing problems. Loose or worn components in the engine. Defective crankshaft counterweights. Loose or worn components in the propeller hub. Loose airframe components.

Fundamentals of Balancing Avoiding the Pitfalls Some indications are: Applying numerous (more than 3 or 4) solutions without reducing the amplitude. Phase angle changing radically between runs. Phase angle that changes dramatically during data acquisition. (At amplitudes below approximately .05 IPS this is not a defect.)

Fundamentals of Balancing Avoiding the Pitfalls In any of these cases, you will have little to no success with your balancing efforts. If you feel you are chasing the solution, check the equipment on another application before blaming your difficulties on the analyzer.

Review Understand the Fundamentals of Propeller Balancing What equipment is required Setting up the equipment Data collection and processing The balancing process Avoiding the pitfalls

Contact www.acessystems.com 1-865-671-2003 sales@acessystems.com