AS APPLIED TO ELECTRONIC MUSICAL PRODUCTION AND PERFORMANCE Part One – Basic training JIM DuBARR – INSTRUCTOR MICHAEL FUSON – COURSE CONSULTANT CREATED.

Slides:



Advertisements
Similar presentations
EXAMPLE OF POSITIVE FEEDBACK. WHAT IS FEEDBACK Feedback- The high-pitched squeal or ringing caused by sound finding its way out of the loudspeaker back.
Advertisements

Introductory Circuit Analysis Robert L. Boylestad
Kit Building Class Lesson 4Page 1 R and X in Series Inductors and capacitors resist the flow of AC. This property is called reactance. Resistance also.
INTRODUCTION With this chapter, we begin the discussion of the basic op-amp that forms the cornerstone for linear applications; that is, the signal is.
1 Crossovers Manual Reference Pages 222 – 227 Manual Reference Pages 222 – 227.
Measurement of Voltages and Currents
Speakers Read Yamaha manual pgs Read Yamaha manual pgs The cone, usually made of paper, plastic or metal, is attached on the wide end.
Foundations of Physics
L 25 Electricity and Magnetism [3] Electric circuits what conducts electricity what doesn’t conduct electricity Current, voltage and resistance –Ohm’s.
Objectives Define basic components of electricity Define basic components of electricity Recognize the 3 electrical classifications of materials Recognize.
DC Choppers 1 Prof. T.K. Anantha Kumar, E&E Dept., MSRIT
1 Output Transducers (Loudspeakers). 2 Loudspeakers  Transducers that convert electrical signals into sound waves  The current flow in the coil causes.
Power Amplifiers and Loudspeakers Power amp ratings Loudspeaker types and uses.
Problem Solving Part 2 Resonance.
1 Live Sound Reinforcement Audio measurements. 2 Live Sound Reinforcement One of the most common terms you will come across when handling any type of.
Foundations of Physics
General Licensing Class G5A – G5C Electrical Principles Your organization and dates here.
Live Sound Reinforcement
Chapter 7 Sound Recording and Reproduction
Power Amplifiers and Loudspeakers Power amp ratings Loudspeaker types and uses.
Capacitors and Inductors.  A capacitor is a device that stores an electrical charge  It is made of two metallic plates separated by an insulator or.
2 1 Amplifiers. Definition A device which increases the level of a signal from line level to power level. Always the final active component in the signal.
Conceptualizing and Constructing the Smart Speaker: Designing a power-limiting device for the common 2-way loudspeaker. Presented by Ryan Gwinn. Project.
Electricity, Electronics And Ham Radio “Kopertroniks” By Nick Guydosh 4/12/07.
electronics fundamentals
Alternating-Current Circuits Chapter 22. Section 22.2 AC Circuit Notation.
Tone Control (Filters).
1 Live Sound Reinforcement Equalizers and other signal processing equipment.
1 Chelmsford Amateur Radio Society Advanced Licence Course Carl Thomson G3PEM Slide Set 4: v1.2, 20-Aug-2006 (3) Technical Aspects - AC Circuits Chelmsford.
General Licensing Class G8A – G8B Signals and Emissions Your organization and dates here.
Inverting Amplifier. Introduction An inverting amplifier is a type of electrical circuit that reverses the flow of current passing through it. This reversal.
Electricity, Components and Circuits
1 Paging and distributed speaker systems BASIC TELECOMMUNICATIONS.
Carlito Espinosa III- Galileo
Electrical Current Mr. Fleming.
SUBELEMENT G5 ELECTRICAL PRINCIPLES [3 Exam Questions – 3 Groups]
Advanced Design Applications Power and Energy © 2014 International Technology and Engineering Educators Association STEM  Center for Teaching and Learning™
Summing Amplifier.
Electric Current and Resistance Physics. Potential Difference  Charges can “lose” potential energy by moving from a location at high potential (voltage)
Sound Principles VCC West Philly Sound Team Training.
Lecture # 16 &17 Complementary symmetry & push-pull Amplifiers
Car Audio Systems. Car Audio Install: FAIL What you need to know! Speakers Subwoofers Tweeters Amplifiers Crossovers Head Units / Receivers Installation.
1 Chelmsford Amateur Radio Society Intermediate Licence Course Murray Niman G6JYB Slide Set 17: v1.0, 25-May-2009 (3) Technical Basics -2: AC & Impedance.
Amplifiers and Speakers
Electrical Production of Sound 1Electric Circuits 2Electric Current 3Resistance 4Voltage 5Ohm’s Law 6Series and Parallel Circuits 7Electric Energy and.
Sound and Its System. What is sound? basically a waveform of energy that is produced by some form of a mechanical vibration (ex: a tuning fork), and has.
Technician License Course Chapter 3 Lesson Plan Module 4 – Electricity.
Electrical Principles 1 1 G5 - ELECTRICAL PRINCIPLES [3 exam questions - 3 groups] G5A - Reactance; inductance; capacitance; impedance; impedance matching.
Objectives Define basic components of electricity Recognize the 3 electrical classifications of materials Compare and contrast AC vs. DC Explain the concept.
Signal Analyzers. Introduction In the first 14 chapters we discussed measurement techniques in the time domain, that is, measurement of parameters that.
Chapter 12 Preview Objectives The Production of Sound Waves
Copyright © 2005 Heathkit Company, Inc. All Rights Reserved Automating and Integrating Residential Systems Presentation 4 – Control of Entertainment Equipment.
Concepts of Engineering and Technology Copyright © Texas Education Agency, All rights reserved. 1.
Physics Mrs. Dimler SOUND.  Every sound wave begins with a vibrating object, such as the vibrating prong of a tuning fork. Tuning fork and air molecules.
MULTIWAY SPEAKER SYSTEM
DC Circuits DC Circuits. Overview Ohms Law and Power Series Circuits Parallel Circuits Series Parallel circuits.
Unit 7, Chapter 20 CPO Science Foundations of Physics.
Transformers and Impedance. Review Two types of current: –ac –dc Two fundamental principles: –Moving electrons create magnetic fields –Moving or changing.
As Unit 1 - Electricity What you need to know..  Current is the rate of flow of charged particles.  In metals these are conduction electrons, most electrons.
4.2.3 Resonant filters. Following this session you should:- Recognise and sketch the characteristics for a simple band-pass filter; Be able to draw the.
Chapter 18 Waves and Sound
Main Speaker – 5674 Specifications Frequency Response
Three Way Cross-over Frequency network
Preamplifier and mixers, Power Amplifiers, and Speakers
Foundations of Physics
POWER AMPLIFIERS.
electronics fundamentals
Amplifiers Classes Electronics-II
Amplifiers Classes Electronics-II
What is the ability to store energy in an electric field called?
Presentation transcript:

AS APPLIED TO ELECTRONIC MUSICAL PRODUCTION AND PERFORMANCE Part One – Basic training JIM DuBARR – INSTRUCTOR MICHAEL FUSON – COURSE CONSULTANT CREATED BY JIM DuBARR ENTERTAINMENT. ALL RIGHTS RESERVED. USE OF ALL MATERIALS CONTAINED HERIN IS AUTHOIZED TO ALL MEMBERS OF THE SAINT JOSEPH MUSIC FOUNDATION FOR PURPOSES OF EDUCATION ONLY.

DEFINITIONS OHMS LAW SOLVING EQUATIONS USING OHMS LAW WHAT IS FREQUENCY MORE ABOUT FREQUENCY THE FREQUENCY SPECTRUM SPEAKER CONSTRUCTION FREQUENCY AND SPEAKERS CROSSOVERS EQUALIZERS

IMPEDANCE IMPEDANCE MATCHING SERIES AND PARALLEL CONNECTIONS POWER HANDLING CAPABILITIES RMS vs. PEAK WATTAGE TOTAL HARMONIC DISTORTION READING SIMPLE SPECIFICATION SHEETS (Specs )

CURRENT The flow of electrons within an electronic circuit. Measured in Amperes Electronic symbol – I Also known as amps. RESISTANCE Opposition to the flow of electrons in an electronic circuit. Measured in Ohms Electronic symbol – R Also represented by Omega

VOLTAGE The potential, or pushing power, of electricity available to a circuit. Measured in Volts Electronic symbol – E Also symbolized as V POWER The measure of the ability of an electronic circuit to accomplish a task. Measured in Watts Electronic symbol – P Also symbolized as W

CURRENT – AMPS - I VOLTAGE – VOLTS - E RESISTANCE – OHMS - R POWER – WATTS - W E IR

With any two variables, the third may be found by using the following simple formulas; E (Voltage) = I (Current) x R (Resistance) I (Current) = E (Voltage) R (Resistance) R (Resistance) = E (Voltage) I (Current)

Frequency is the essence of Sound Frequency is defined as the time between the reoccurrence of the same event Sound waves create pressure waves in the air that vibrate the ear drum, causing us to “hear”. These sound waves are sinuodal, or modulate from zero to a positive level, then to an equal negative level, then back to zero again. The period of time it takes for this cycle to occur is called the “frequency”. In electronics, this is measured by what is called a “sine wave”, which resembles a sideways “S”. Frequency is measured in units called Hertz, abbreviated as Hz, also called Cycles per Second.

LOW FREQUENCY Low frequency sound waves are long, and repeat less frequently. Low frequency sounds, like that of a bass, vibrate the ear drum less often, so we hear low sounds. HIGH FREQUENCY High frequency sound waves are short, and repeat more often. High frequency sounds, such as lead guitar, vibrate the ear drums more often, so we hear a higher sound.

Low Frequencies 20 Hz to 250 Hz Midrange Frequencies 250 Hz to 2 kHz (2000 Hz) High Frequencies Above 2 kHz to extent of hearing capabilities.

PLACEHOLDER FOR PICTURE OF SPEAKER

Low Frequency Larger magnets and coils are necessary to produce low frequencies. More power is necessary to energize these large coils, which are actually resistors by nature. Power is measured in watts, low frequency speakers require more wattage to produce sound. High Frequency Smaller magnets and coils are needed to produce high frequency sound waves. Less power is needed to energize the smaller coils of these speakers, consequently there is less resistance in this circuit. Less wattage is necessary to power these speakers, a smaller Power amp can be used.

Crossovers are adjustable frequency dividers which allow selected frequencies to pass, or be blocked from passing, to speakers. In simple terms, crossovers provide a means of allowing only lower frequencies access to larger bass speakers while blocking higher frequencies. At the same time they allow only higher frequencies to pass through to the smaller speakers and horns, while blocking the lower frequencies, which could damage the smaller speakers. Crossovers can be two way, or three way which additionally allows control over frequency distribution to Midrange speakers.

Equalizers allow the user to control the volume of individual frequencies distributed to speakers. Equalizers allow for fine tuning of the force of sound waves produced by the speaker for each of the adjustable frequency ranges by providing resistance to the chosen frequency being adjusted. Using Ohms Law, we can see that more resistance means less voltage. Understanding speaker construction, the speaker will vibrate less, producing less powerful sound waves in the adjusted frequency range.

Typical 32 Band Equalizer Two-Way Crossover

Please take this time to jot down any questions you may have. This presentation will be available online through the Foundation’s website. A comprehensive five part course is available through the Foundation as well. There is no cost for these services, however donations to the Foundation will be accepted. Questions (and possibly tutoring) can be addressed to the following links after tonight’s presentation. Thank you for attending! Jim DuBarr – Mike Fuson –

Impedance is simply the combined resistance of all components of any given circuit. Since it is resistance, it is measured in ohms. Multiple speaker enclosures usually contain an internal crossover to separate frequencies between the different size speakers in the cabinet. The resistance of this crossover, combined with the resistance of the speakers themselves, represents the impedance.

 To insure proper operation of speakers and power amplifiers, it is important to match the impedance of the speakers to the output of the power amplifier used.  Failure to insure proper impedance matching may damage speakers and power amplifiers, and at a minimum will shorten the useful life of the items.  Most matching can be done easily by either choosing the corresponding output on the power amplifier, or in some cases setting a control on the power amplifier for the correct output impedance. Many power amplifiers match impedance automatically through sensing circuits.  Most speaker enclosures are 4, 8 or 16 ohm impedance.

How you connect multiple speakers together can have an effect on total impedance of the circuit. SERIES – one cable connects the power amplifier to the first speakers input. The second speaker is connected from the first speakers output to the input of the second speaker. In this scenario, if the first speaker’s impedance is 4 ohms, and the second is 4 ohms, the total impedance of the circuit is 8 ohms. PARALLEL – separate cables connect each speaker to a separate output of the power amplifier. Each speaker maintains it’s own impedance rating.

Because there are no universally accepted standards, most professional loudspeaker manufacturers use different test methods to arrive at a power handling specification. This rating does not necessarily correspond to the best amplifier size to use nor is it a measure of the "safe" amplifier size to use under actual operating conditions. There are three separate and very distinct issues regarding selecting amplifier power for loudspeakers. 1. LOUDSPEAKER POWER HANDLING RATING 2. SELECTING AN APPROPRIATE AMPLIFIER SIZE 3. PREVENTING LOUDSPEAKER DAMAGE If an audio system is operated improperly, damage to or failure of a loudspeaker can occur even with an amplifier sized well below the loudspeaker’s power rating. Contrarily, if an audio system is operated properly, damage to or failure of a loudspeaker can be avoided even with an amplifier sized well in excess of the loudspeaker’s continuous (or RMS, average, etc.) power rating..

RMS, or Root Mean Standard, describes the point in a signal, or frequency when distortion begins to occur. This can be heard by turning a radio up to full volume and listening. Once the volume is decreased, you hear less unnatural noise other than the sound itself. RMS is 70.7% of the peak Wattage. Example: 100 watts peak=70.7 watts RMS. Above 70.7 watts, distortion will increase proportionally to the maximum allowed by the design of the circuit. Simply put, a volume knob incremented 1-10 will begin to produce distortion of the signal when turned to 8 or above.

Music is made up of both Fundamental and Harmonic Frequencies. A note produced by a musical instrument, A for example, is producing a fundamental frequency of 440Hz or cycles per second. It is also reproducing harmonics of that frequency that are multiples of the fundamental frequency, such as 880Hz, 1220Hz, 1760Hz and so on. Each of the harmonic frequencies is lower in level or volume than the fundamental, but they serve to give each instrument its unique sound. When the total harmonic distortion of an amplifier is measured, the difference in the level of the harmonics at the output stage of the amp is compared to the level of the harmonics at the input stage, and the difference is the extent of the distortion.

Behringer B212XL SYSTEM DATA High-performance woofer B212XL: 12" (305 mm) B215XL: 15" (381 mm) Tweeter compression driver B212XL and B215XL: 1.75" (44 mm) Frequency range B212XL: 65 Hz to 18 kHz B215XL: 55 Hz to 20 kHz Power rating B212XL: 800 W Peak Power 200 W Continuous Power (IEC ) B215XL: 1000 W Peak Power 250 W Continuous Power (IEC ) Impedance B212XL and B215XL: 8 Ω Sensitivity (1 1 m) B212XL: 95 dB (Full Space) B215XL: 96 dB (Full Space) Dispersion B212XL: 90° x 60° B215XL: 70° x 40° Crossover frequency B212XL: 1.9 kHz B215XL: 2.0 kHz DIMENSIONS/WEIGHT Dimensions (HxWxD) B212XL: approx. 21 2⁄3" x 13 5⁄8" x 10 5⁄8" (approx. 550 mm x 345 mm x 270 mm) B215XL: approx. 27 1⁄3" x 17 1⁄3" x 13 1⁄16" (approx. 695 mm x 440 mm x 335 mm) Weight B212XL: 24.0 lb / 10.9 kg B215XL: 38.7 lb / 17.6 kg

THANK YOU FOR ATTENDING TONIGHTS PRESENTATION 2009 – Jim DuBarr Entertainment – All Rights Reserved – Unauthorized Duplication is Prohibited