Example Water at 95°C is flowing at a rate of 2.0 ft3/s through a 60° bend, in which there is a contraction from 4 to 3 inches internal diameter. Compute.

Slides:

Advertisements

Similar presentations

Fluid Mechanics.

Advertisements

CE 382, Hydraulic Systems Design (pipes, pumps and open channels) Principles of hydraulics 1.Conservation of energy 2.Continuity (conservation of mass)

Aula Prática 1 Propriedades dos fluidos e unidades.

CTC 261 Bernoulli’s Equation.

Pharos University ME 259 Fluid Mechanics for Electrical Students Revision for Mid-Term Exam Dr. A. Shibl.

Momentum Conservation

Pharos University ME 352 Fluid Mechanics II

Continuity Equation Tutorial

Fluid Mechanics 10.

CE 230-Engineering Fluid Mechanics Lecture # BERNOULLI EQUATION.

Negative if into control volume Positive if out of control volume In simple unidirectional flow casesIn general Unit normal pointing out from control volume.

Pertemuan CLOSED CONDUIT FLOW 1

CE 230-Engineering Fluid Mechanics Lecture # 9 & 10 Hydrostatic forces on plane surfaces.

Forces Acting on a Control Volume Body forces: Act through the entire body of the control volume: gravity, electric, and magnetic forces. Surface forces:

CE 230-Engineering Fluid Mechanics

FE Hydraulics/Fluid Mechanics Review

CHAPTER 6 MOMENTUM PRINCIPLE Dr. Ercan Kahya Engineering Fluid Mechanics 8/E by Crowe, Elger, and Roberson Copyright © 2005 by John Wiley & Sons, Inc.

Application of the Momentum Equation

SURVIVAL MODE Quiz 3 –

Fluid Properties: Liquid or Gas

Molecular Transport Equations. Outline 1.Molecular Transport Equations 2.Viscosity of Fluids 3.Fluid Flow.

Reynold’s Number Reynold’s number is ratio of inersial forces & viscous forces & have no units. N Re = ρDU/µ ρ = Density of fluid (g/cm3) D = Diamerter.

ENT 257: MULTIPLE CHOICE QUESTIONS

Principles of hydraulics Conservation of energy (Bernullie)

CHAPTER 5: PRESSURE 5.1 Pressure and Its Units

Unit: V-Flow Through Pipes. Flow Through Pipes  Major Energy Losses - Darcy-Weisbach Formula - Chezy’s Formula  Minor Energy Losses -Sudden expansion.

Unit: IV-Fluid Dynamic

CTC 450 Energy Equation.

Practical Applications Wind Turbine Hydropower Turbine The motion of a fluid is altered so that propulsive forces can be generated on the devices. The.

CTC 450 Bernoulli’s Equation EGL/HGL.

Problems Ch(1-3).

QUESTIONS. Last class  Continuity  Bernoulli Equation.

Area of a Sector and Length of an arc Ms N. Kearney.

Estimating The Viscosity Bio-fluids Bien 301 Jasma Batham.

Lesson 23 HEAD LOSS DEFINE the terms head loss, frictional loss, and minor losses. DETERMINE friction factors for various flow situations using the Moody.

Fluid Resistance.

اگر حجم کنترل در حال حرکت بود چه سرعتی در فرمول؟ + –

Jan cm 0.25 m/s y V Plate Fixed surface 1.FIGURE Q1 shows a plate with an area of 9 cm 2 that moves at a constant velocity of 0.25 m/s. A Newtonian.

CBE 150A – Transport Spring Semester 2014 Other Friction Losses Valves and Fittings.

AL Fluid P.44. V~ 1m x 0.4 m x 0.2m ~ 0.01 m 3 Density  = M/V ~ 100kg / 0.01 = kg m -3.

Fluids. Introduction The 3 most common states of matter are: –Solid: fixed shape and size (fixed volume) –Liquid: takes the shape of the container and.

One Minute Paper Statics; reply. Fluid dynamics  Fluids in motion Pumps Fans Compressors Turbines Heat exchangers.

Physics Section 8.3 Apply the properties of flowing fluids The flow of a fluid is laminar if every particle that passes a particular point moves along.

Statika Fluida Section 3. Fluid Dynamics Objectives Introduce concepts necessary to analyse fluids in motion Identify differences between Steady/unsteady.

Pharos University ME 259 Fluid Mechanics for Electrical Students Revision for Final Exam Dr. A. Shibl.

Application of the Continuity Equation Dr. Eyad Abushandi.

Bernoulli Equation – Pitot tube  Horizontal  Velocity at stagnation point is 0  Incompressible fluid  Steady state  Velocity as function of pressure.

CFD Exercise 1 Laminar & turbulent flows with COMSOL.

SUGGESTED MINIMUM KNOWLEDGE OF FLUID MECHANICS AND FOR FE EXAM

Momentum Equation and its Applications

60 1. What is the mass M in the system as given in the

EXERCISES Two water reservoirs are connected by a pipe 610m of 0.3m diameter, f’=0.038 and the flow produced by the difference in water surface elevations.

Pimpri Chinchwad polytechnics

Waller Creek 8th Street Side Weir CFD Modeling and Simulation

KINEMATICS 1. A nozzle is so shaped that the velocity of flow along the centre line changes linearly from 1.5 m/s to 15 m/s in a distance of m. Determine.

CTC 450 Energy Equation.

Chapter 4. Analysis of Flows in Pipes

2 in G=0.002 in Calculate the required torque in lbf-ft and heat loss (power consumption) in horsepower to turn the shaft on the friction bearing shown.

CTC 450 Bernoulli’s Equation EGL/HGL.

Control volume approach (검사체적 방법)

Chapter 5. Pipe System Learning Outcomes:

Line Sizing By Shardul Kulkarni.

PO 2430 Applied Fluid MEchanics

Applications of Bernoulli Equations

9. FLUID FLOW: Working Problems

Bottle Rocket Calculations

Dynamics of Machinery Problems and Solutions

Bottle Rocket Calculations

Presentation transcript:

Example Water at 95°C is flowing at a rate of 2.0 ft3/s through a 60° bend, in which there is a contraction from 4 to 3 inches internal diameter. Compute the force exerted on the bend if the pressure at the downstream end is 1.1 atm. The density and viscosity of water at the conditions of the system are 0.962 g/cm3 and 0.299 cp, respectively.

Example A jet of water having a velocity of 30 m/s and a diameter of 2.5 cm is deflected by a smooth, flat vane, where there are no changes in elevation or pressure before and after impact. What is the force of the jet on the vane?

Quiz 4 – 2013.12.04

Quiz Water is flowing at steady state through a reducing bend as shown below. The angle 2 = 90, and the pressure at point 2 is 1.0 atm abs. The flow rate is 0.020 m3/s and the diameters at points 1 and 2 are 0.050 m and .030 m, respectively. Neglect frictional and gravitational forces. Calculate the resultant forces on the bend. TIME IS UP!!!