Pc Naming Configuration 1.WEB REGISTER 2.FIXNAME 3.MCAFEE AGENT SETUP ITC Training: Session 2

WEBREG Why use Webreg? –Take control over network infrastructure –Ease of information –Better Security Clients needs to contact helpdesk to connect pc to network –Management of connecting computers –Uses DHCP to assign IP addresses ( statically assigned )

Webreg: Requirements before a registration is made 1 Make sure the Client’s Tcpip settings are correctly set up for DHCP 2 The mac address of local network interface card (NIC) 3The subnet where the PC is currently standing 4 The user’s network ID

Webreg: 1. Client Settings The Tcpip Properties and under Advanced, the DNS tab must be set up for DHCP to assign IP addresses.

Webreg: 2. Finding the Mac Adres 2 Ways! 1.Click on Start -> Run and type in CMD and enter –Type in ipconfig /all and enter –The Mac Address will be the Physical Address of the NIC

Webreg: Finding the Mac Adres (Cont.)

2.Right Click Local Area Connection under Network Connections Status Support Details Webreg: Finding the Mac Adres (Cont.)

Webreg: Subnet and Hostname The Hostname is the users personnel number and this must be made available to the person that will run the Webreg program. The Subnet must also be known. ITC can be contacted if the Campus IT staff is unclear about the subnet assigned for the pc that needs to be webreged.

Using the URL in IE6 – Access is given via Novell authentication Following slide shows the login screen in Webreg Webreg: Where do I find the interface?

Click on Yes Webreg: Interface: Internet Explorer

Novell Credentials is required to log on to Web Register Webreg: Interface: Internet Explorer

Webreg: Page Display See Next Slide

Webreg: Description of tabs Hostname: = P(University Number of client) Mac: = NIC Physical address Subnet: = Where computer connects to network Description: = Can be left blank Save: = Register PC on Network Search: = Looking for PC on Network

Webreg: Name Conventions Each additional pc for the same user is registered with a “-” and then the number following (counting the number of pc’s the user has) Example: p is the hostname of pc1 and p is the hostname of the second pc of the same user. Very IMPORTANT!!!! ONLY the “-” is allowed apart from alphanumeric characters. As convention we use the “p” for personnel ( or “s” for students ) and then followed by the personnel/student number ( any number between 0-9 )

Webreg: Example: New Registration Click Save

Webreg: Example: “Save” Results

Webreg: Search A few Search Examples –Search by Hostname and/or –By Subnet. –Use * as a wildcard in searches

Webreg: Example: Input to see all itbab* entries Click Search

Webreg: Search Results

Webreg: How to activate IP Address After a new ID is saved on the Webreg site it is updated on the Nameserver & in the DHCP Leases file The update happens in intervals of 5 minutes Restart the pc after you registered the PC on webreg In a Command Prompt verify that the pc has a valid IP address using the Ipconfig /all command An example of an valid IP address is as follows *.*

Webreg: How to activate IP Address (cont) What to do if you don’t have a valid IP address after you rebooted the pc 2 Options: 1.In a command prompt type in ipconfig /release (This releases the current Apipa ip address automatically assigned by Microsoft Windows) and ipconfig /renew (This will contact the DHCP server to verify if there is a valid IP assigned to the computers Physical Address. It will then assing a valid IP for the client pc)

Wegreg: How to activate IP Address: Option1: Ipconfig It is sometimes necesarry to run the ipconfig /renew command more than once, this is due to the fact that the update takes place in intervals of 5 minutes The following slide shows a typical ipconfig /release & ipconfig /renew instruction

Wegreg: How to activate IP Address: Option1: Ipconfig

DHCP gives out not only the ip but all required TCPIP info: Suffixes, Gateway and DNS Server addresses: How to activate IP Address: Option1: “Ipconfig /all” – output

2.Repair the network connection: Right Click Local Area Connection under Network Connections Status Support Repair (Sometimes needs to be done more than once) Webreg: Activate IP Address: Option 2: Repair Connection

Fixname Why? –To set the computer name as Unique –To make sure the pc and hostname are linked – better control and for simplicity –For the sake of the Mcafee Epo server and management of computers – it needs unique names

Fixname: Prerequisite: DNS Webreg must have been run for the Computer as Fixname does a nslookup and then it writes the name found for the local ip address as the computername To make sure please run “ipconfig /all” on the pc to be fixnamed. If the ip is in the “ x.x” range the regsiter was sucessful. Ipconfig /release and Ipconfig /renew can be run if the webreg was done seconds ago – or just restart the pc if the x.x network ip is not allocated.

Fixname: File Output IP Address: Host Name: ITBABM2 Netbios Name: ITBABM2 DNS Name: ITBABM2 Always reboot the pc after this has been done and before continuing with fixagent.

Fixagent: Prerequisites 1. Pc must have a valid IP and hostame in DNS. Webreg must have been executed. 2.Fixname must have been executed so that the computername used by Mcafee to generate the Agent guid is unique 3. Verify by using ipconfig /all in command prompt ( for DNS ) or the “Hostname” command ( to see the computername.)

FixAgent: Agent Issue explained When imaged pc’s are connected the GUID in the Registry will match that of the original pc from which the image was made. Mcafee over- writes the entry with the same guid in its database with the entry from the agent that last connected to the server. Thus only one entry exists in Mcafee for all pc’s with the same guid. FixAgent.exe fixes this issue. When executed it runs in the background. Give it a minute or two and then connect to the agent interface on the pc: to verify the agent is running.

New / Imaged Pc setup review: Get the subnet,mac address and hostname and Webreg the pc. Use Ipconfig (or details tab via the connection properties) to see if the Ip is in the x.x. range. Fixname the pc and reboot. The hostname can be checked with the Hostname command. Run FixAgent. Give it a minute or two to finish in the background. Check the localhost:8081 http URL to verify the agent is running.

Finish Other things to remember to check for: Printer installed after login to novell? Remedy ID ( When logged into novell and run “Requester.exe” from desktop ). Run Groupwise ( log into Novell and run ) Netmeeting: Set up User ( Start, run, and type “conf” and go through the prompts )