UNT in partnership with TEA,.Copyright ©. All rights reserved. Engineering Design and Presentation.

Slides:

Advertisements

Similar presentations

HOW TO MAKE A ROCKET BY SAM CANNINGTON. THE FUSELAGE 1.Cut out a thin peace of cardboard.

Advertisements

Engineering Design and Presentation Auxiliary Drawing 1 UNT in partnership with TEA. Copyright ©. All rights reserved.

Engineering Design and Presentation Auxiliary Drawing 1 Copyright © Texas Education Agency, All rights reserved.

ENS 207 engineering graphics

Volume: The Disk Method

(Re)Learning The Basics Feet and Inches Perimeter Area Volume Proportions.

Engineering Design and Presentation

Auxiliary Views.

Chapter 7 Pictorials Topics Exercises.

Rotation of Two-Dimensional Solids

FLOOR PLANS APPLICATIONS OF TECHNOLOGY. WHAT IS A FLOOR PLAN?  A floor plan is drawing of a building with the roof removed as seen from above.  The.

Engineering 1182 College of Engineering Engineering Education Innovation Center Revolve Rev: , AJPRevolve1.

PLANOMETRIC VIEW OF A KITCHEN.

Geometric Solids EQ: What are the most common types of solids, what are cross sections and solids of revolution?

Rockets Read and follow along. On your journals, draw the rockets and label. Draw and label the parts of the rockets and answer the questions listed.

Warm-Up Draw and name the 3-D solid of revolution formed by revolving the given 2-D shape around the x-axis.

Copyright © Texas Education Agency, All rights reserved. Engineering Design and Presentation.

1.Tim is painting his living room with a new coffee colored Paint. There are 3 walls in the living room that measure 15 ft by 8 ft each and a fourth wall.

ISOMETRIC PROJECTION Part II

Ken YoussefiIntroduction to Engineering – E10 1. Various Blade designs Ken YoussefiIntroduction to Engineering – E10 2.

Engineering Design and Presentation Solid Modeling Solid Modeling Drawing UNT in partnership with TEA, Copyright ©. All rights reserved. UNT in partnership.

Identifying 3-D Figures Lesson 12 – 7. Vocabulary Three Dimensional (3 – D) Figure: Shapes that have a length, width, and depth/height Face – a flat surface.

Strategy Using Strategy1. Scan Path / Strategy It is important to visualize the scan path you want for a feature before you begin taking points on your.

Greg Kelly, Hanford High School, Richland, WashingtonPhoto by Vickie Kelly, Disk and Washer Methods Limerick Nuclear Generating Station, Pottstown,

Lesson 72, day 2 Pyramids and Cones. Pyramids Pyramid: geometric solid with a polygon base, and triangle faces (lateral faces) Vertex: top of the pyramid.

Interior Design II: Objective 5.02

Engineering Design and Presentation Solid Modeling Solid Modeling Drawing UNT in partnership with TEA, Copyright ©. All rights reserved. Copyright © Texas.

I CAN UNDERSTAND RATIOS and PROPORTIONS. In this lesson you will use ratios and proportions in order to draw actual objects onto a paper.

How to read an Architect’s Scale

INTERPRETING WORKPLACE DOCUMENTS Principles of Architecture and Construction UNT in partnership with TEA. Copyright ©. All rights reserved.

Creating the wheel by revolving Revolved Profile.

Marshall has a sandbox in the shape of a square prism, as shown below. The height of the sandbox is 10 inches. If Marshall fills the sandbox with sand.

Copyright © Texas Education Agency, All rights reserved. Architectural Design Architectural Models.

Introduction to 3D Solids and Solids of Revolution Some 3D shapes can be formed by revolving a 2D shape around a line (called the axis of revolution).

How to read an Architect’s Scale

How to read an Architect’s Scale

Reading an Architect’s Scale

Lesson Geometric Solids -- Prisms and Cylinders

Robotics and Automation

Applications of Technology

The Shell Method Section 7.3.

Forging new generations of engineers

Alternate Views Introduction to Engineering Design

Engineering Design and Presentation

Warm-up Solve for segment WV. Solve for x..

Additive & Subtractive Solid Modeling

Auxiliary Views.

Oblique Pictorials Introduction to Engineering DesignTM

Volumes of Solids of Revolution

ENGN103 Engineering Drawing

Revolve A solid can be created by revolving a shape around an axis.

True Shapes Pointers for the Exam Worked Example True shape Tips

Isometric and Oblique Pictorials

Sketching Multiview Drawings

ENGN103 Engineering Drawing

Chapter Seven Constructions and Scale Drawings

2 types of scale factor problems

Forging new generations of engineers

Sketching Multiview Drawings

Chapter Seven Construction and Scale Drawings

ENGN103 Engineering Drawing

Sketching Multiview Drawings

Miniature Train Smoke Stack.

6.1 Estimating with Finite Sums

Engineering Design and Presentation

Volumes of Revolution: Disk and Washer Method

Geometry: Three Dimensional Solids

Revolve A solid can be created by revolving a shape around an axis.

Forging new generations of engineers

Presentation transcript:

UNT in partnership with TEA,.Copyright ©. All rights reserved. Engineering Design and Presentation

Introduction In this lesson, students will learn how to accurately and neatly to scale complete a revolve drawing of a nose cone. UNT in partnership with TEA. Copyright ©. All rights reserved.

Lesson Objectives 1. Define terms associated with the lesson: height, width, axis, planes. 2. Identify views and dimensions. 3. Lay out overall shape in 2-D and convert to a solid. 4. Identify and understand a polyline. UNT in partnership with TEA. Copyright ©. All rights reserved.

Storyboard - to revolve an object  Construct all segments to the shape of choice. (In this case a nose cone.)  Close all ends to line segments.  Revolve the object around an axis.  Choose the axis line from top to bottom of object.  Choose the revolutions ( 360 degrees ) full circle.  Enter and the object will revolve. UNT in partnership with TEA. Copyright ©. All rights reserved.

2-D Drawing

UNT in partnership with TEA. Copyright ©. All rights reserved. Revolve of Nose Cone

By using the same method, see if you can do this problem. Can you revolve your own wheel? UNT in partnership with TEA. Copyright ©. All rights reserved.

How many parts can you revolve? If you wish to fly this rocket to these scales and this thrust (example 27 psi) it will travel 75 feet. UNT in partnership with TEA. Copyright ©. All rights reserved.

From examples below use your own dimensions and revolve.