Legacy-GW Features Rev1.4 24 Jan., 2013

Over view Chapter 1: Product Overview . 2

Over view 1.Use NCP/TDE（TDA）as a legacy GW by stacking connection with NS1000. 2.NCP/TDE(TDA) connect with NS by stacking card working as part of One-look network.

Over view Introduce new card ; STACK-M (for NS), STACK-S (1 for NCP/ 1 for TDE) Site #1 STACK-M card Slave Units NS1000 as stacking Master Unit Master for One-look Site #2 Site #3 Stacking Slave NCP500 NCP1000 LAN Stacking Slave Stacking Slave Site #4 　： Stacking Slave STACK-S card Proprietary cable for stacking connection The length of the cable：2M (Dedicate cable for these Stacking card) 4

Over view New card Symbol Model Name Description Remark STACK-M KX-NS0130 Stacking Master Card - Interface card for Legacy-GW - Proprietary Interface x 2 ports Symbol Model Name Description Remark STACK-S (NCP) KX-NS0131 Stacking EXP Card for NCP Legacy-GW Control Unit for NCP with Stacking Cable (TDE/TDA) KX-NS0132 Stacking EXP Card for TDE/TDA Legacy-GW Control Unit for TDE/TDA

Condition Chapter 1: Product Overview .

Condition 1 1.MPR of NCP has to be removed to install Stack-S card. This means Virtual card on NCP is not supported. All of IP terminal has to connect to NS1000. 2.Type of GW has to be same for each NS1000. 　Category1: NCP500 /NCP1000 　 Category2: TDE100/200, TDA100/200 Category3: TDE600/620, TDA600/620 3.Max 2 GW for each NS. Max 8 for entire One-look network. 4.TDA15/30/50/100D is not supported. 5. AK is not required to use Legacy GW. STACK-M card Stacking Slave #1 Stacking Slave #2 *If the type of cabinet is mixed then 2nd one will not be worked. STACK-S card 7

Condition 2 In case of TDE600 each cabinet count as 1 GW and connection to NS has to be done by Stack-S card. Bus card in TDE600 and TDE620 has to be removed. NS1000 NS1000 NS1000 TDE620 TDE620 TDE600 TDE600 TDE620 TDE600 OR OR 8

Which Optional card can not be used at Legacy GW? Condition 3 Which Optional card can not be used at Legacy GW? Symbol Model Description RMT TDA0196 Analogue Modem for Remote Maintenance MEC TDA0105/ TDE0105 Memory Expansion Card DSP4 NCP1104 VoIP channel card 4ch DSP16 TDE0110 VoIP channel card 16ch DSP64 TDE0111 VoIP channel card 64ch CTI-LINK TDA0410 CTI Link Card IP-EXT16 TDA0470 16-Channnel VoIP Extension Card IP-GW4E TDA0484 4-Channnel VoIP Gateway Card IP-GW16 TDA0490 16-Channnel VoIP Gateway Card IP GW4 TDA0480 4 Channel VoIP Gateway Card MSG4 TDA0191 4-Channel Message Card ESVM2 TDA0192 2-Channel Simplified Voice Message Card ESVM4 TDA0194 4-Channel Simplified Voice Message Card CLCOT8 TDA1180 8-Port Analogue Trunk Base Card w/ Caller ID CLCOT8E TDA1186 8-Port Analogue Trunk Daughter Card w/ Caller ID MCSLC24 TDA1178 24-Port Single Line Telephone Card MCSLC16 TDA1176 16-Port Single Line Telephone Card Basically Optional card 1)on TDE/NCP MPR 2)Support by V5 or later 3) IP-GW, IP-EXT 4) MSG are not supported. 9

Condition 4 How many CO can be installed in each Legacy GW? Stand-alone Stacking system One Look Networking 1NCP500 1NCP1000 1TDE/TDA100 1TDE/TDA 200 1TDE/TDA 600 2NCP500 2NCP1000 2TDE/TDA 100 2TDE/TDA 200 2TDE/TDA 600 Trunk(ch) 256 600 IP SIP H.323 48 96 Legacy 30 64/64/120/128/160 128/128/240/256/256 LCOT 2 12/16/96/128/160 24/32/192/256/256 BRI 8 PRI23 23 46/46/92/92/115 92/92/184/184/230 PRI30 60/60/120/120/150 120/120/240/240/256 T1 48/48/96/96/120 96/96/192/192/240 E1 10

Condition 5 How many EXT can be installed in each Legacy GW? Stand-alone Stacking system One Look Networking 1NCP 1TDE/TDA100 1TDE/TDA 200 1TDE/TDA 600 2NCP 2TDE/TDA 100 2TDE/TDA 200 2TDE/TDA 600 Extension(ch) 640 1000 IP IP-PT 256 SIP SIP Phone KX-UT series S-PS(SIP based DECT) 255 Legacy *1 2 44/160/256/304 88/320/512/608 SLT 36/96/128/240 72/192/256/480 DPT 40/128/256/256 80/256/512/512 Legacy DECT PS 512 has not been changed. 11

Condition 6 How many other devices can be installed in each Legacy GW? Stand-alone Stacking system One Look Networking 1NCP 1TDE/TDA100 1TDE/TDA 200 1TDE/TDA 600 2NCP 2TDE/TDA 100 2TDE/TDA 200 2TDE/TDA 600 CS (pcs) 64 128 DPT-CS (2ch) 11/32/32/32 22/64/64/64 DPT-CS (8ch) 5/16/16/16 10/32/32/32 IP-CS 64 *2 128 *2 SIP-CS 64 *3 128 *3 PS(DECT)(pcs) 512 VM Built-in UM (ch) 24 24ch x16 TVA/TVM (ch) 48 (24ch x2) 24ch x8 *2 The maximum number of Air Sync Groups is 16. An Air Sync Group can contain up to 16 IP-CSs. *3 The maximum number of Air Sync Groups is 8. An Air Sync Group can contain up to 32 SIP-CSs.

Condition 7 AK on NCP/TDE can’t be transferred to NS MPR. In case of TDA100/200 and TDE100/200 OPB3 card with ECHO16 must be installed in only SLOT1. - Other than OPB3 card allows to install in any SLOT. - OPB3 card with sub-card except for ECHO16 allows installing in any SLOT. HGT100, NT400 can’t be connected to NS MPR. 13

How to work?

How to work? Installation Both Stack-M and Stack-S card is non hot swappable. Each cabinet can be power on without any order. Initial Legacy-GW installation, all card will be initialized. The optional service cards is hot swappable. TVM can be installed as VM system for entire One-look. CS can be installed at both NS(NCP0158) and Legacy-GW (TDA0141/142/155/156/158). PS can Hand over between these CS to CS(NCP0158, TDA0141/142/155/156/158).

How to work? Wireless Hand over between NS to Legacy GW and Legacy GW to Legacy GW is available. LAN IP-CS IP-CS(NCP0158) CS CS(TDA0141/142/155/156/158) PS CS CS If Legacy CS and IPCS are mixed then all CS must be assign under Air sync group 1.

How to work? Start up LED Status “Stack-M” LED Green On : Normal working condition Off: Error( Not Working) “Stack-S” LED Green On : INS Red On : Fault Red Flash: OUS Legacy GW “RUN” LED Green Off :Power off On : Running as GW Slow Flash: While start up “ALARM” LED Red Off : No present error On : Present Error

How to work? Maintenance All below service for Legacy-GW is supported through NS1000 cabinet. Programming Firmware update Error log, Syslog SNMP information SMDR

Programming

Programming Programming at NS1000 Button to switch Physical-Virtual-LegacyGW1-LegacyGW2 Stack S connect to “1” on Stack M consider as “GW1” Each Optional Card can be selected and installed.

Programming Programming at NS1000 LPR Software :Software can be download through NS1000 LPR Software name same as existing models LPR Software for STACK-S card “PSTKS” is new!

Programming Programming at NS1000 Programming items related to Legacy GW support. Related to VM. Related to DSS. Port Property

Appendix

Appendix Supported optional card

Appendix Supported optional card

Appendix Supported optional card

END

Modification 20120827-01 LegacyGW_Rev1_27Aug2012Mar.ppt - 1st release 20120905-02 LegacyGW_Rev1_1_5Sep2012Mar.ppt - Edit slide #11 revise number of legacy EXT and DPT. - Add slide #12 20121031-03 LegacyGW_Rev1_2_31Oct2012Mar.ppt - Add comment for slide #7 “No AK required” - Add additional sample for slide #8 - Add comment for slide #9 “Basic idea” - Add comment for #13 about HGT100 and NT400 - Add remark for #16 20121108-04 LegacyGW_Rev1_3_8Nov2012Mar.ppt - correct slide #8 600-620 twice to 600-620 and 620-620 20130124-05 LegacyGW_Rev1_4_24Jan2013Mar.ppt - correct slide #10 BRI and LCOT capacity for NCP500 as Legacy GW