Internet Telephony PBX System IPX-300/1900 Series How to connect with Analog PBX via FXO Module or FXS/FXO Gateway Configuration Copyright © PLANET Technology Corporation. All rights reserved.

Please refer to the following descriptions and insert proper parameters configurations into the device for establish the voice communications.

Installation Scenario: 1. Company A connect with CO line with FXS gateway The local extension (# 600) could communicate with other company and IP Phone via network. 2. Company B connect with Analog line with FXO gateway The local extension (# 700) could communicate with other company and IP Phone via network. 3. Company C connect with Analog line with FXO module of IPX-1900 The local extension (# 800) could communicate with other company and IP Phone via network.

Select the [IP PBX Setup -> SIP Extension] of IPX-1900 to create the extensions for IP Phone, FXO/FXS gateway. 1

Select the [IP PBX Setup -> FXO Trunk] of IPX-1900 to define DID to IVR settings. 2

Select the [IP PBX Setup->Gateway Trunk] of IPX-1900 to create the Gateway Trunk for the FXS/FXO gateway. 3 IP : 172.16.0.3 (FXO Gateway) Port : 5060 (SIP Port) Afterward click the Insert to add that 4

Select the [IP PBX Setup -> Trunk Group] of IPX-1900 to add the Trunk Group 5 To add a Trunk Group for FXO module Group Name : Company_C Number : 90 Trunk Group : FXO_Port_1 FXO_Port_2 6

Select the [IP PBX Setup -> Dialing Rules] of IPX-1900 to add the Dialing Rule for FXO Gateway 7 To add a Dialing Rules for FXO Gateway Phone NO. : 92. Delete Length : 0 Trunk Group : 172.16.0.2:5060 8

Select the [Hunt Group Setting] of IPX-1900 to add a Hunt Group for FXS Gateway. Create an Hunt Group : Group Name : Company_A Hunt Mode : Round Robin Hunt Group Service Number : 91 Ring Timeout : 30 Ring Group : 201, 202, 203, 204 10

Select the [Save & Logout] of IPX-1900 to create a SIP trunk which connect with Gateway 11 Click on the button to save previous modification and take effect, the system will rebooting, please wait for 50 sec 12

Select the [Advance Setup ->VoIP Basic] of FXS Gateway to setting port number configuration. 13 VoIP Basic Configuration: Number :201, 202, 203, 204 Check Reg Account: 201, 202, 203, 204 Password: 123 Use Public Account: Disable 14

15 SIP Proxy Setting: Domain/Realm: 172.16.0.1 SIP Proxy Server: 172.16.0.1/5060 SIP Authentication : Enable About the IP address please refer to previous topology.

Select the [Advance Setup ->VoIP Basic] of FXO Gateway to setting port number configuration. 16 VoIP Basic Configuration: Number :301, 302, 303, 304 Check Reg Account: 301, 302, 303, 304 Password: 123 Use Public Account: Disable 17

18 SIP Proxy Setting: Domain/Realm: 172.16.0.1 SIP Proxy Server: 172.16.0.1/5060 SIP Authentication : Enable About the IP address please refer to previous topology.

Select the [Dialing Plan] of FXO Gateway to add the Dialing Plan Number. 19 Incoming Dial Plan Settings: Outgoing no: 92x Length of Number: 3 ~ 6 Delete Length: 2 Prefix no.: None Destination Telephone Port : 1,2,3,4 20

For example: A. From Company A 1. To IP Phone: #600 dial #601~604, hear dial tone, dial 200 2. To Company B: #600 dial #601~604, hear dial tone, dial 92700 3. To Company C: #600 dial #601~604, hear dial tone, dial 90, hear dial tone, dial 800 B. From Company B 1. To IP Phone: #700 dial #701~704, hear dial tone, dial 200 2. To Company A: #700 dial #701~704, hear dial tone, dial 91 , hear dial tone, dial 600 3. To Company C: #700 dial #701~704, hear dial tone, dial 90, hear dial tone, dial 800 C. From Company C 1. To IP Phone: #800 dial #801~802, hear welcome prompt, dial 200 2. To Company A: #600 dial #801~802, hear welcome prompt, dial 91 , hear dial tone, dial 600 3. To Company B: #600 dial #801~802, hear welcome prompt, dial 92700 C. From IP Phone 1. To Company A: IP Phone dial 91, hear dial tone, dial 600 2. To Company B: IP Phone dial 92700 3. To Company C: IP Phone dial 90, hear dial tone, dial 800