Neonatal Chest Compression Device Courtney Gallagher 1, Jillian Zeber 1 Advisors: Paul King 1, PhD; William Walsh 2, MD Vanderbilt University, Biomedical.

Slides:



Advertisements
Similar presentations
Introduction to Pneumatic Components Build a Working Pneumatic Circuit
Advertisements

A force applied over a surface is pressure.
Fluid Power Hydraulic Cylinders
Cylinder performance characteristics. Piston force Cylinder performance characteristics can be determined theoretically or by the use of manufacturer’s.
Experiment 2-2 Pressure versus Force.
Engine Terminology Engine Measurement Lesson 8 March 2008.
Pneumatic Components & Systems Team 1640 Clem McKown – mentor November 2008.
Neonatal Chest Compression Device Courtney Gallagher Jillian Zeber Advisor: Dr. Walsh, Vanderbilt NICU.
0 Beach Cities Robotics Pneumatics August 12, 2007 Rick Wagner, APM, Redwood I&T Northrop Grumman Corporation.
Mechanical System. Agenda Mechanical Systems – Contest Outcomes Basic Pneumatics The Kit of Parts.
 Air! A pneumatic assembly is one that converts energy stored in compressed air to mechanical energy. Electrical Energy Compressed air Mechanical force.
Fluid Power Introduction
ZOLL AutoPulse ® Non-invasive Cardiac Support Pump.
Hydraulics.
Presented by Jon Pannell
Pneumatic Chest Compression Device for CPR Kyra Ceceris, Daniel Metzinger, Tina Mornak University of Pittsburgh Senior Design – BioE Mentor:
PIT Crew Design Concepts By Dan Chapman, Tim Wilson, and Jon Miller December 11, 2002.
Pneumatic Hand Computer controlled pneumatics Project components:
Actuators.
Fluid Power Introduction
Sensors and Actuators John Errington MSc. Sensors and Actuators Sensors produce a signal in response to a change in their surroundings e.g. Thermostat.
Neonatal Chest Compression Device Courtney Gallagher Jillian Zeber Advisor: Dr. Walsh, Vanderbilt NICU.
Electro-Pneumatics Module 1
Vanderbilt University School of Engineering Software-driven Pneumatic Beating Heart Simulator and ECG Display Jacob Bauer, Nicole Rice, Ashley Whiteside.
Chapter 10 Fluid Power Systems.
Fluids. Flow Take shape of container Liquids or gases Exert pressure Pressure = force / area Fluids
Client: Ken Campbell, Ph.D. Advisor: Glennys Mensing
Mentors Workshop Pneumatic Sub-System Mark McLeod Team 358 Festo/Hauppauge H.S. F For I Inspiration and R Recognition of S Science and T Technology.
What is Fluid Power? Fluid power is energy transmitted and controlled by means of a pressurized fluid, either liquid or gas. The term fluid power applies.
1Abstract Our objective was to design an infusion pump that will be used to deliver contrast agents during a MRI exam. Currently used is a syringe pump.
Manual Control Systems: Pneumatics “A Slice of Mechanical Engineering” Mr. J. Butler ● Department of Technology & Engineering ● John Jay High School ●
SIZING PNEUMATIC SYSTEMS. Introduction Pneumatic systems are sized to meet output power requirements. The air distribution system is sized to carry the.
Pressure P = Force per unit area = F/A SI units: = N/m 2 = Nm -2 = 1 pascal = 1 Pa.
Blood Pressure Monitor Re-Calibration Lei Qu 1, Ross Hamilton 1,David Lee 1, Haniff Mohd Nor 2 Advisor: Dr. Andre Churchwell 3, Dr. Paul King 1 Acknowledgments.
Standard Grade Technological Studies
Pneumatic and hydraulic actuation system (cont.)
Evaluation of Ergonomics of Data Entry System in Neonatal Intensive Care Unit John Fonge 1, Kendra Mills 1, and Brandy Scott 1 Advisor: Dr. William Walsh,
Warlocks 8/5/05 TMU Pneumatics on Robots u Simplified model Compressed Air Tank Geek Safety Glasses 60 lbs Pneumatic Cylinder Whoa! That’s a lot of force.
P16452: Active Reciprocating Compressor Valve Assembly Week 9: Subsystem Design Review.
Neonatal Chest Compression Device Courtney Gallagher Jillian Zeber Advisor: Dr. Walsh, Vanderbilt NICU.
Engineering Concepts Chapter 5 Terms. ACTUATOR A device that transfers fluid or electrical energy into mechanical energy.
Neonatal Chest Compression Device Courtney Gallagher Jillian Zeber Advisor: Dr. Walsh, Vanderbilt NICU.
Warlocks 8/5/05 TMU FIRST Robotics 101 u Week 1) Gears, Pulleys, Sprockets, Bearings u Week 2) Motors & Controls u Week 3) Pneumatics u Week 4) Materials.
The KOP Mechanical. Main Groups Control System (C) Base Components – Frame and frame hardware (F) – Gearbox (G) and motors – Wheel kit (W) Pneumatics.
BASIC AUTOMATIC CONTROLS UNIT 16 ADVANCED AUTOMATIC CONTROLS
Fluid Power Introduction © 2012 Project Lead The Way, Inc.Principles of Engineering All images reprinted with permission of National Fluid Power Association.
Enrollment No Name of Student: PAREKH KISHAN JAGDISHBHAI.
Manufacturing Engineering Hydraulic and Pneumatic Systems
H & P Formulas Engineering II – August The parts and values of concern…. D 1 = diameter of cylinder (in) D 2 = diameter of piston rod (in) P 1 =
Double Acting Cylinder
Engineering II – August 2016
Directional control valves
Fluid Power Introduction
Cardiopulmonary Resuscitation
Fluid Power Introduction
SimMan Improvements Dr. Matt Weinger, MD Ray Booker Advisors:
Actuators and directional control valves
Device Specifications
Introduction to Pressure, Pneumatics, and Hydraulics
Nursery Chart System Development
Fluid Power Introduction
Fluid Power Introduction
Industrial Electronics
Breast Pedicle Protector
INTRODUCTION TO PNEUMATICS
Module – 4: Single Acting Cylinder
By: JAGDEEP SANGWAN Refrigeration Basics 101.
Fluid Power Introduction
Actuators & Directional Control Valves
Fluid Power Introduction
Presentation transcript:

Neonatal Chest Compression Device Courtney Gallagher 1, Jillian Zeber 1 Advisors: Paul King 1, PhD; William Walsh 2, MD Vanderbilt University, Biomedical Engineering 1, Monroe Carell Jr. Children’s Hospital 2 INTRODUCTION DESIGN APPROACH RESULTS ACKNOWLEDGEMENTS PROTOTYPE EVALUATION CALCULATIONS OBJECTIVES DESIGN/SAFETY CRITERIA Figure 1. Dr. Walsh demonstrates how to provide manual chest compressions on the NICU simulation baby, Isabel. COST BREAKDOWN Chest compressions to restart the heart may need to be performed simultaneously with abdomen or neck surgery on a 0-30 day old infant. Since the surgeons cannot stop the surgery, another surgeon must perform the compressions. There is limited space around the infant due to their size and there isn’t any room for another person to provide compressions. 2 occurrences in the Vanderbilt NICU this past year (as seen by Dr. Walsh) Must perform adequate chest compressions to the standards of Dr. Walsh: Take up little space in the NICU Provide compressions at least as effective as the traditional, manual method of chest compressions Be safe, non-harmful to the baby Used in Vanderbilt NICU and other hospital NICU’s Design Criteria: Reduce the chest width by one third (2-3 cm) Provide compressions per minute Apply pounds of force Be portable with quick/easy set up Solutions to Safety Issues: Completed DesignSafe Develop instruction manual and training program Sterilization with plastic drapes No more than 12 lbs of force can be applied MaterialCost per Unit Air Cylinder $15 3-Way Solenoid Valve $109 Electronic Timer $80 Coiled Air Hose $33 25’ Tubing $12 Air Compressor $200 Wall Plug $7 TOTAL UNIT COST: $456 Table 2. Cost evaluation per unit of material, which is significantly lower than adult devices currently on the market. 1.1”diameter plunger attached to 2”bore- piston to displace chest 2-3 cm Wheel-up cart supporting electronic components & air compressor Stand with base and adjustable arm holds the cylinder directly above the infant’s chest Figure 2. Compressed air travels through the hose to actuate the air cylinder during the on-position of the solenoid valve. Figure 3. The solenoid valve is controlled by an electronic timer and power is supplied via a wall outlet. Air Cylinder Mechanics: F = p A = p π d 2 /4 F = force exerted (N) p = gauge pressure (N/m 2, Pa) A = full bore area (m 2 ) d = full bore piston diameter (m) From testing: F = 11 lbs = 50 N p = 100 psi = kPa d = 10 mm ≈ 7/16” 80/min90/min100/min Cycle Frequency (s -1 ) Cycle Length (s) On/Off time (s) Table 1. A rate of compressions per minute results in on/off times of seconds. Timer On/Off time: Cycle Length = 1/Cycle Frequency On/Off time = Cycle Length/2 Figure 4. The prototype is tested on Isabel with the air cylinder positioned directly above the center of the chest right beneath the nipples. The device was tested on the NICU SimNewB simulation baby, Isabel. The SimNewB supplies lifelike clinical feedback, determining whether the chest compressions provided by the device are adequate by measuring blood flow rate. Single-acting spring return pneumatic cylinder actuated by compressed air via an air compressor with coil hose Air flow controlled via 3-way solenoid valve with an electronic timer Power supplied via a wall outlet (120 V, 60 Hz) FUTURE DIRECTIONS Create instruction manual Evaluate the effectiveness against traditional method Build a permanent support structure with a wide base Implement feedback via force sensitive resistors Try for FDA approval REFERENCES " Cost Effective Comprehensive Training Program Targets Rural Community Hospitals." Laerdal: Helping save Lives. Laerdal Medical, Halperin, MD, MA, Henry R et al. "Cardiopulmonary Resuscitation with a Novel Chest Compression Device in a Porcine Model of Cardiac Arrest: Improved Hemodynamics and Mechanisms." Journal of the American College of Cardiology 44 (2004): "Pneumatic Air Cylinders - Force Exerted." Engineering Toolbox. Web. 18 Apr We would like to thank the following for their support and help with our senior design project: Mary Lee Lemley, MSN, RNCKent Meeks, GE John DunbarVU Dept. of Chemistry Joel Barnett, PhD Comparison: 1.Lucas: $14,500 2.Thumper: $5,000 3.Autopulse: $13,000 Figure 6. The 11-lb cut-off equals a minimum of 72 psi of compressed air. Figure 5. When tested on Isabel only applied forces greater than 11 lbs. were adequate.