Drill Press Instructions and Safety.. Safety Glasses Safety Glasses MUST be worn in the wood shop at ALL TIMES.

Slides:



Advertisements
Similar presentations
The drill press is the preferred tool for making holes in materials.
Advertisements

Sanders and Sanding Safety
Safety Always Wear Safety Glasses when in the Wood Shop.
Power Tools Safety. Portable Circular Saws Stock must be well supported in such a way that the kerf will not close and bind the blade.. Thin materials.
Handling Kitchen Emergencies. Burns Run cold water over burned area. Never use butter or direct ice.
Drill Press. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in.
Portable Power Tool Safety. Portable Electric and Cordless Drill Be sure the electric drill is disconnected from the power source before installing bits.
Sliding Compound Miter Saw Safety & Use. Safety Rules Always keep hands at least 4” away from blade Always allow the blade to get to speed before cutting.
Machine Shop Hazards, Machine Tool Safety
Portable Grinders Stationary Grinders
200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt.
Research & Development Machine Safety Information.
Technology Education Shop and lab safety Band Saw Scroll Saw
Stationary Power Tool Safety
Unit 53 Metalwork Technology and Practice
General Shop Safety. No horseplay. Do not operate machines or power- tools until you are licensed.
Band Saw Safety Rules. Safety Rule #1 Keep all guards in place. Keep all guards in place.
Manufacturing Technology Safety: Band Saw. Safety Rule #1  Keep all guards in place.
Woodworking with Power
SAFETY RULES Follow all directions the first time they are given. Be courteous in language and actions. Be on time and prepared to participate. Respect.
Grimsby Secondary Construction Technology Equipment Safety.
Drills and Drill Press Safety in the Lab
Module-6 Drilling.
Copyright © Texas Education Agency, All rights reserved. Flexible Manufacturing Basic Safety 1.
BAND SAW SAFETY Pre-TEST. You should not support the stock with your hands on each side of the blade as a cut is being made. FALSE – support the stock.
RIPPING, CROSSCUTTING, CUTTING ANGLES, COMPOUND ANGLES, CUTTING DADO’S AND CUTTING RABBET’S.
Safety Rules for 9 th Grade Shop Radial Arm Saw: Safety Rules Never cut a board that is less than 12 inches long. Always pull the saw using the handle;
Toni Somma-Cavaluzzi 8/20/2003 Stained Glass Safety Rules Toni Somma-Cavaluzzi.
Print out your WPBD Bridge. Write your name and period here.
Basic Lab Safety.
Shop Cleanup and Organization. Objectives Use shop cleaning equipment properly Clean benches, machines and floors Store materials properly Store tools.
Food and Nutrition Kitchen Safety. What are the most common Kitchen Accidents? Burns Cuts Falls Fire Poisoning.
General Safety. A student may not work in the shop unless the instructor is present. Absolutely no exceptions !!
Harding High School Technology Lab Safety Power Machine Review Mr. Pottkotter & Mr. Robinson.
Auto/Metal Shop Safety: General Safety
Shop Safety Safety is everyone's business and responsibility.
Safety in the Machine Shop Session 1. Shop Tools and Techniques2.
Power Machine Safety Harding High School Mr. Robinson/ Mr. Pottkotter.
General Safety Foundations of Engineering and Technology I.
HEADS UP FOR SAFETY! SAFETY TUTORIAL. HEADS UP! H ANDS ARE THE MOST VULNERABLE PART OF THE BODY. E YES AND EARS ALSO NEED PROTECTION. A SK WHEN YOU ARE.
Router Safety Foundations of Agriculture I Mr. DeBord.
Model Agricultural Core Curriculum: Supplement University of California, Davis 911.T 1 Basic Hand and Power Tools Hand Tool Safety Carry with sharp point.
Band Saw Safety Prevent an accident- be safe and smart!
By Christian Grecco. Drill Press 5. Hold material securely with a vice or clamps. 6. Be sure the chuck key is removed from the chuck before starting the.
Ms. Wilson WOODSHOP SAFETY LESSONS & VIDEOS. BASIC SAFETY 1. Eye protection must be worn while using power equipment and bladed hand tools 2. No loose.
DRILL PRESS. 1. Belt cover 2. Speed control High speed for soft materials, such as wood. Low speed for hard materials, such as metal. 3. Chuck & chuck.
1 Metal Shop Safety Automotive 10, 11, 12 Metal Shop Safety Automotive 10, 11, 12.
General Safety Foundations of Engineering and Technology.
Band Saw Safety in the Lab. Common Techniques Parts of the Band Saw.
Band Saw Safety Prevent an accident- be safe and smart! Copy down Copy down everything in black.
General Shop Safety and Fire Safety. 1 All students CLEAN up 2 Watch out for others and ask if you’re not sure. 3 Pay attention to the job 4 If you bleed.
General SafetyBand SawScroll Saw Miscellaneous Machines Next.
Scroll Saw Operation and Safety
1 Scott Highlands Middle School Technology Education “ Drill Press Safety Notes ”
Machine Safety Rules. Miter Saw Instructor must be present when you are using this machine. Keep wood flat and against fence Hold down wood Do not remove.
On/off switch Depth stop Quill lock chuck Tilting table Lower table or base Variable speed pilot wheel motor Feed handle Table locking clamp column.
Drill Press Safety and Operation. Westward 10” Drill Press The drill press comes in a floor or bench-mounted model. It has a motor driven head that has.
Portable Electric Drills By: Mason Young. 1. Properly secure drill bits in the chuck of the portable drills.
Parts, Safety and Operation. 1. Fence 2. Table 3. Miter Adjusting Lever 4. Miter Scale 5. Turn Base 6. Vertical Hold-Down Vise 7. Arm 8. Slide.
Drill Press Safety Livonia Churchill High School Industrial Technology.
General & Machine Safety Notes
Flexible Manufacturing
Lab Safety.
Power Tool Safety Don’t operate a machine until:
Anti-Kickback Fingers
Mr. Lidard’s Guide to Keeping All Your Body Parts
Drill Press Safety.
Motorized Miter Saw.
Livonia Churchill High School Industrial Technology
Safety in Engineering Class
Presentation transcript:

Drill Press Instructions and Safety.

Safety Glasses Safety Glasses MUST be worn in the wood shop at ALL TIMES

This is a Drill Press

The On and Off Switch

Drill Press Handle

Drill Bit

Depth Adjustment

Holding Material to drill

Always Hold your material If this happens, do not grab the material. Turn off the drill press and wait for it to stop.

Clean up of Drill Press Throw away scrap wood and sweep off drill press table

Clean up of Drill Press Sweep off and around drill press stand.

Clean up of Drill Press Use hand brooms to sweep off drill press and sweep into dust pan. Use big brooms to sweep floors

Clean Up No one is excuse from class until the woodshop is clean.

Using Drill Press