Press Forming By Lewis & Joe What Is Press Forming Where Is It Used In

Slides:

Advertisements

Similar presentations

Drop Forging By John , Brendan and Keith What is drop forging

Advertisements

Metal processes Press forming Sand casting Die casting Milling

Metals All metals belong to one of these two groups.

Alloys Noadswood Science, 2012.

Engineering Materials Resource 4 Manufacturing Techniques.

WHAT IS MANUFACTURING? Why do we study manufacturing?

Bending and shaping materials in the DT workshop.

GCSE Resistant Materials Techniques and Processes

Solid State Welding Processes

Plastic Process AS Graphics.

Materials. 1  Which of the following is a soft wood? 1. Mahogany. 2. Jelutong 3. Oak 4. Beech 5. Pine.

BASIC MECHANICAL ENGINEERING. MANUFACTURING PROCESSES.

Spot Welding Quiz Steel Aluminium Copper High Speed Steel 1.Spot Welding is most commonly used to join which material ?

Specification section 1.2

What is the Injection Moulding?

Intermediate 1 Unit 2a Metals

Forming. There are 4 main types of forming these are Press forming Embossing Deep drawing Spinning Forming comes under processing metals in redistribution.

Permanent Mould Casting

Chapter 4: Sheet Metal Forming Shafizan Bt. Shariffuddin School of Manufacturing Engineering UniMAP 1. SHEET METAL AND CHARACTERISTICS.

To understand how the injection moulding process works.

Learning Intention: Show a working knowledge of various metals

Metals Design and Manufacture. Metals Produced by mining ore from the Earth Three main categories of metal: ▫Ferrous ▫Non ferrous ▫Alloys Available in.

بسم الله الرحمن الرحیم.

Manufacturing Processes  Rotational Moulding  Compression Moulding  Turning  Blow Moulding  Die Casting  Injection Moulding  Forging  Vacuum Forming.

AS Materials & Processes Design Section - Camera.

Prelim Revision PHOTO HERE. Category 1 Hand tools £100 £200 £300 £400 £500 £ 500 £500 Category 2 Power Tools Category 3 Processes Category 4 Materials.

Resistance Welding The resistance of metal to the localized flow of current produces heat Process variables –Current –Time –Force Spot and seam welding.

Alloys By: Cara Hobson.

Manufacturing, Engineering & Technology, Fifth Edition, by Serope Kalpakjian and Steven R. Schmid. ISBN © 2006 Pearson Education, Inc.,

 To understand how the blow moulding process works.  To be able to identify the processes used in the creation of different plastic products.  To apply.

Forging&forging process Forging is manufacturing process where metal is pressed, pounded or squeezed under great pressure into high strength parts known.

CASTING Hassan Sarwar ME100 4M-10C Oct 18, OBJECTIVE: Objective of this presentation is to give an introduction on the process of casting, which.

Chris Cass Mike Danylko Bryan Haring

Shaping Metal. Bending Metals can be bent in a vice or in folding bars Folding Bars.

Metals All metals belong to one of these two groups. Ferrous metals are metals, which are mainly made of iron with small amounts of other metals or elements.

Reforming Processes Blow Moulding.

1 Manufacturing process II. Manufacturing process II. Sándor Pálinkás Ph.D. assistant lecturer University of Debrecen, Faculty of Engineering, Department.

Resistance welding. Conti…… Resistance Welding is a welding process, in which work pieces are welded due to a combination of a pressure applied to them.

Resistance Welding Resistance Welding is a pressure welding technique using high current and low voltage The current passing through the two overlapping.

SHEET METAL OPERATIONS

Metals and Processes Theory. Knowledge and Understanding.

Metal Properties and Processes Design and Manufacture.

Mr. A Roberts GCSE Resistant Materials Materials and their Uses - Metal.

Introduction to nonferrous metal and alloys

Ferrous and non-ferrous alloys

FERROUS & NON FERROUS ALLOY

Forming By Kyle Durham. Manufacturing forming An important production process is forming. An important production process is forming. Forming allows to.

WIRE DRAWING: DRAWING Typical drawing processes: 1.Single draft drawing 2.Tandem Drawing - Cold working improves the mechanical properties - Intermediate.

Metals. Ferrous metals – contain iron Non-ferrous – contain no iron Alloys – a mixture of two or more metals.

What is the Injection Moulding?

Metals All metals belong to one of these two groups.

MOP UP SUBJECTS.

Joining Processes A2.

Metals All metals belong to one of these two groups.

National Design and Manufacture

Why do we study manufacturing?

Materials and Processes

Metals All metals belong to one of these two groups.

Pictures and cars.

Applications of Reciprocating Saw

What is Product Design – the design style questions in the coming exam

Metals There are two categories of metal Ferrous & Non Ferrous

Starter 1– Metals and alloys test

Spot Welding Quiz.

Chapter 6: Mechanical Properties of Metals

Presentation transcript:

Press Forming By Lewis & Joe What Is Press Forming Where Is It Used In Manufacturing? Advantage/Disadvantages Materials Used Process

What Is Press Forming When pressure is applied to sheet metal to form a mould. Automated process where sheet metal is fed from a coil into die set. Products that has been press formed

Where Is It Used In Manufacturing? It is used in car manufacturing to create the car bodies It is used to make kitchen sinks It is used to make aircraft panels Here are pictures of other press formed products

Materials Used Sheet Metals: Copper Various Steels Brass Alloys Aluminium

Process Step 1 Cut The Metal Or Plastic Step 2 Heat The Metal Or Plastic Step 3 Put Into Mould Step 4 Apply Pressure To Moulds Step 5 Remove Metal Or Plastic From Mould

The END!! By Lewis & Joe