Repair Guide SMP-Series Products

page 2 Agenda Warning Product Disassembly ○ SMP-WEBPLUS ○ SMP-WEB / SMP-PRO2 ○ SMP-WEB3 / SMP-PRO3 SMP-WEB3N / SMP-PRO3N Product Serial Number and License Key

Warning!

page 4 [Important] Only Cayin Authorized Resellers are allowed to perform the procedures in this document. You may violate the warranty if you disassemble Cayin’s product without permission.

page 5 Notice Before you disassemble an SMP player ○ Wear antistatic gloves to prevent damaging components ○ Carefully use a screwdriver and not to harm the surface of PCB ○ All connectors must be plugged in the correct direction

Product Disassembly SMP-WEBPLUS

page 7 1. Logo and Model 2. Mark 3. Product information and serial number sticker Package (1)

page 8 1. Product 2. Accessories (Power cable, wall- mount kit, product CD) 3. Product Quick Installation Guide Package (2)

page 9 DISASSEMBLY SMP-WEBPLUS PLAYER Unscrew Case Unscrew Case Disassembly Steps Remove Hard-Disk Drive Remove Hard-Disk Drive Remove DOM & DRAM Remove DOM & DRAM Remove Power Supply Remove Power Supply Remove Motherboard Remove Motherboard Finish STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6

page 10 Unscrew top case and open it. Unscrew Case

page 11 1.Motherboard 2.DRAM & Disk-on-Module (Store system firmware) Inside Player 3.Hard-Disk Drive 4.Power Supply

page 12 Remove Hard-Disk Drive (1) Unplug the IDE cable and the power connector (1, 2, 3) Unscrew four screws and remove the HDD bracket from the product case

page 13 Remove Hard-Disk Drive (2) Unscrew HDD from the bracket You must set HDD to master for using it in SMP-WEBPLUS

page 14 Remove DOM DOM (Disk-on-Module) locates besides DRAM Remove it gently from IDE connector

page 15 Remove DRAM Press 2 DRAM latches and remove it from the socket

page 16 Remove Power Supply (1) Unplug ATX power connector Press the latch and pull up the connector

page 17 Remove Power Supply (2) Unscrew five screws then you can remove power supply from its place

page 18 Unscrew five screws; then you can remove the power supply Remove Power Supply (2)

page 19 Remove front panel connector Remove Motherboard (1)

page 20 Loose the 4 screws at 4 corners of the motherboard Remove the motherboard from the box Remove Motherboard (2)

page 21 Disassembly - Finish

page 22 Installation-Wall Mount SMP-WEBPLUS equips wall- mount kit to let you mount the player on the wall or behind the screen Beware of the ventilation when you install player; don’t block air circulation

Product Disassembly SMP-WEB/SMP-PRO2

page 24 Package Product package and Serial Number sticker

page 25 DISASSEMBLY SMP-WEB/SMP-PRO2 PLAYER Remove Upper Case Remove Upper Case Disassembly Steps Remove CF, HDD & HDD Rack Remove CF, HDD & HDD Rack Remove DRAM Remove DRAM Unlock Rear Panel Unlock Rear Panel Remove Motherboard Remove Motherboard Finish STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6

page 26 Remove Upper Case Slide the upper case backward to open it.

page 27 Inside Player 1.DRAM 2.HDD and HDD racket 3.HDD upper rack screw

page 28 Remove CF and HDD Release the HDD rack screw, you can remove HDD upper rack from the base The firmware Compact Flash Card locates beneath the HDD Remove CF card by dragging it in the direction of arrow

page 29 Remove HDD from Drive Bay Unplug IDE cable and remove HDD from the box Unscrew four screws around the upper rack and remove HDD You must set HDD to the slave mode

page 30 Remove HDD Rack Unscrew those 4 screws around the HDD rack

page 31 Remove DRAM Push DRAM’s latch to unlock DRAM from socket.

page 32 You can unload the rear panel by unscrewing it in two sides. Inside Player

page 33 Remove Motherboard Gently remove the motherboard by sliding it in the right direction.

page 34 Disassembly - Finish

Product Disassembly SMP-WEB3/SMP-PRO3 SMP-WEB3N/SMP-PRO3N

page 36 Remove Power Supply (1) Product package Model and package information Serial number sticker

page 37 DISASSEMBLY SMP-WEB3(N) / SMP-PRO3(N) PLAYER Remove Box Remove Box Disassembly Steps Remove Cover Remove Cover Remove HDD Remove HDD Remove DOM Remove DOM Remove Motherboard Remove Motherboard Finish STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6

page 38 Take out the box from the package carton Remove Box

page 39 Remove Cover To remove the upper cover, you must unscrew four screws on the top and bottom.

page 40 Inside Player After opening the top cover, you will see (1) Slim HDD (2) Firmware flash (DOM)

page 41 Remove HDD (1) To remove HDD and the rack from the box, you must release four screws in four corners. After removing HDD and rack, you can release HDD screws from rack.

page 42 Remove HDD (2) You must set HDD to master for SMP- WEB3/ PRO3/ WEB3N/ PRO3N

page 43 Remove Firmware DOM To remove the firmware flash disk (DOM), just unplug it from the IDE socket

page 44 Remove Motherboard (1) To remove the motherboard from the box, you must release 4 hexagonal screws from the VGA and COM port connectors.

page 45 Remove Motherboard (2) Release 4 screws around the corners and remove the motherboard from the case

page 46 Disassembly - Finish

Product Serial Number and License Key

page 48 Serial Number Serial Number is very important to communicate with Cayin You can find Serial Number on Carton and Product Box The initial 2 letters is product model:  SW: SMP-WEB  SP: SMP-PRO2  WP: SMP-WEBPLUS  WE: SMP-WEB3  PR: SMP-PRO3  CM: CMS server

page 49 License Key You can find the product license key on the rear panel of the product. It combines 8~10 digits. When you recover the system or replace the system flash memory, you will be asked to enter the Key in first start up.