In this paper, we present a novel approach for the design of an edge-type LED backlight unit (BLU) with no light guide plate. The effect of several important.

Slides:



Advertisements
Similar presentations
Optical sources Lecture 5.
Advertisements

1 Graphics CSCI 343, Fall 2013 Lecture 18 Lighting and Shading.
DESIGN OF 2.2-INCH LED BACKLIGHT UNITS FOR BRIGHTNESS UNIFORMITY AND REDUCTION OF HOT-SPOT EFFECT Jeng-Feng Lin, Chin-Chieh Kang, and Chih-Yang Liu Department.
Reduction of the Hot-Spot Effect on the Light Guide Plate by Inverted Pyramid Arrays Jeng-Feng Lin, Chin-Chieh Kang, Pei-Chiang Kao Department of Electro-Optical.
Natural light illumination system Irfan Ullah Department of Information and Communication Engineering Myongji university, Yongin, South Korea Copyright.
ANALYTICAL HAZE SIMULATION OF OPTICAL FILMS WITH 2D PARABOLOIDAL MICROLENS ARRAY Jeng-Feng Lin, Chin-Chieh Kang, and Shih-Fu Tseng Department of Electro-Optical.
Scattering property of rough surface of silicon solar cells Bai Lu a, b, *,Wu Zhensen a, Tang Shuangqing a and Pan Yongqiang b a School of Science, Xidian.
Optical Fiber Basics Part-3
Geometric Optics The Law of Reflection.
Advanced Plastic Solutions Light & Building 2008 Patent Pending Copyright© DKI Plast as Microprism™ Introducing.
A NEW PRINTED QUASI-LANDSTORFER ANTENNA
Chapter 34 The Wave Nature of Light; Interference
A 21 F A 21 F Parameterization of Aerosol and Cirrus Cloud Effects on Reflected Sunlight Spectra Measured From Space: Application of the.
Radiative Properties of Clouds ENVI3410 : Lecture 9 Ken Carslaw Lecture 3 of a series of 5 on clouds and climate Properties and distribution of clouds.
LCD COMPONENTS. GoalsGoals 1.Light Guiding Plates 2.Reflector Sheet 3.Light Collimator Films 4.Diffusers 5.Polarizers 6.Non - Absorptive Polarizers 7.Quarter.
Newton’s Rings Another method for observing interference in light waves is to place a planoconvex lens on top of a flat glass surface, as in Figure 24.8a.
By Bhaskar Department of Physics K L University. Lecture 07 (25 Aug) Interference in Thin Films.
REFRACTION. When light travels from one material to another it usually changes direction The bending of light that occurs at the borderline of two materials.
© imec 2006 Photonics Europe Design of new collection systems for multi LED light engines Hüseyin Murat 05/04/2006.
Lecture 12 Monte Carlo Simulations Useful web sites:
Reflection and Refraction Chapter 29. Reflection When a wave reaches a boundary between two media, some or all of the wave bounces back into the first.
Antennas The primary elements of a synthesis array M. Kesteven ATNF 25/September/2001.
Advanced Ideal Backlight Illumination System  Illumination of a set of three red, green and blue pixels.  This micro-optical system is replicated many.
A Stable Zn-indiffused LiNbO 3 Mode Converter at μm Wavelength STUT Hsuan-Hsien Lee 2, Ruey-Ching Twu 1, Hao-Yang Hong 1, and Chin-Yau Yang 1 1.
STUST. Abstract Introduction Measurement Setup Experimental Setup Conclusion Reference Sensitivity Enhanced Optical Angle Measurement Using an Immersion.
Attenuation by absorption and scattering
A Member of the ITW Confidential Purpose To demonstrate the versatile uses of backlights beyond traditional LCD applications Objective Overview of backlight.
Automated Electron Step Size Optimization in EGS5 Scott Wilderman Department of Nuclear Engineering and Radiological Sciences, University of Michigan.
Guangzhou Zheng Ming Laser Technology Co.,Ltd. We are a Professional Manufacturer of laser dot Light Guide Plate for LED panel light, LED down light,
Example problem 1 Example problem 2
High Efficiency Uniform LED Surface Light Source Chih-Chieh Kang, Jeng-Feng Lin, Yu-Chang Wu, Shih- Cheng Yeh, Tai-Rong Chen Department of Electrooptical.
Diffraction is the bending of waves around obstacles or the edges of an opening. Huygen’s Principle - Every point on a wave front acts as a source of tiny.
Fringes Color pattern occurs because incident light is not monochromatic.
Yi-Chin Fang, Institute of Electro-Optical Engineering, National Kaohsiung First Univ. of Science and Technology Improvements of Petzval Field Curvature.
Design of Solar Lighting System for Energy Saving
The Analysis of Light Absorption and Extraction of InGaN LEDs Jeng-Feng Lin, Chin-Chieh Kang, Pei-Chiang Kao Department of Electro-Optical Engineering,
J-V Characteristics Optical Properties Above-11%-Efficiency Organic–Inorganic Hybrid Solar Cells with Omnidirectional Harvesting Characteristics by Employing.
Ch 16 Interference. Diffraction is the bending of waves around obstacles or the edges of an opening. Huygen’s Principle - Every point on a wave front.
Congresso del Dipartimento di Fisica Highlights in Physics –14 October 2005, Dipartimento di Fisica, Università di Milano An application of the.
Virtual Mechanism for Displaying Viewing Angle Related Mura of a Backlight Unit in Simulation Chih-Chieh Kang, Jeng-Feng Lin, Cho-Wei Chen, Yu-Chang Wu.
Lecture Outline Chapter 22 College Physics, 7 th Edition Wilson / Buffa / Lou © 2010 Pearson Education, Inc.
Lecture 24 Interference of Light.
Lecture 26-1 Lens Equation ( < 0 )  True for thin lens and paraxial rays.  magnification m = h’/h = - q/p.
Study of Bright “Fringes” near the Incident Surface of a Wedge-Type Light Guide Plate in an Edge-Type Backlight Unit Chih-Chieh Kang, Jeng-Feng Lin, Yu-Chang.
ME 556 Solar Energy Conversion Lecture 9. Radiative Properties: Selective Surfaces & Transparent Materials.
Today’s agenda: Thin Film Interference.
LED Construction – Aim – 100% light emitting efficiency ◘Important consideration - radiative recombination must take place from the side of the junction.
Refraction The bending of light due to a change in speed.
A STUDENT’S EXPERIMENT WITH MULTIPLE REFLECTIONS AND REFRACTIONS ON A GLASS PLATE AND VALIDATION OF THE FRESNEL’S EQUATIONS N. Mahmudi 1, S. Rendevski.
3. OLED panel Organic light emitting diodes (OLEDs) with a quasi-crystal (QC) structure are analyzed and applied in a head-mounted display (HMD) system.
1 Electromagnetic waves: Multiple beam Interference Wed. Nov. 13, 2002.
Optical Design, Fabrication and Measurement Associate Professor: Yi-Pai Huang Department of Photonics and Display Institute 2010/02/25.
Optical Design of Phosphor Sheet Structure in LED Backlight System
Light and Optics  The Electromagnetic Spectrum  Interference, Diffraction, and Polarization Wave Properties of Light.
Lecture 26-1 Lens Equation ( < 0 )  True for thin lens and paraxial rays.  magnification m = h’/h = - q/p.
Light Engine Design and Manufacturing Development in Projection System
Speaker: Hao-Wen Chuang ( 莊浩彣 ) Advisor: Prof. Chung-Hao Tien ( 田仲豪 助理教授 ) Prof. Yi-Pai Huang ( 黃乙白 助理教授 ) Display Institute, National Chiao Tung University,
LOGO Benefits of LED flood lightsLED flood lights.
Computer Graphics: Illumination
Date of download: 7/9/2016 Copyright © 2016 SPIE. All rights reserved. Schematic diagrams of (a) our novel wide viewing LCD, consisting of a collimated.
A Multi-Performance Film for Highly Efficient LCD Backlights
Speaker: Bo-Wen Xiao ( 蕭博文 ) Advisor: Prof. Yi-Pai Huang ( 黃乙白教授 ) Prof. Chung-Hao Tien( 田仲豪教授 ) Institute of Electro-Optical Engineering, National Chiao.
Optical Fiber Basics Part-3
Color pattern occurs because incident light is not monochromatic.
VW 370 Optical Feasibility
Meeting 指導教授:李明倫 學生:劉書巖.
© 2003 University of Wisconsin
Chapter 22 – The Nature of Light
Today’s agenda: Thin Film Interference.
Presentation transcript:

In this paper, we present a novel approach for the design of an edge-type LED backlight unit (BLU) with no light guide plate. The effect of several important design parameters, such as BLU height, LED position, location of bumpy structure as well as its height, on illuminance uniformity is examined. Typical simulation results are presented. They demonstrate the feasibility of our devised approach. Shih-Cheng Yeh, Shao-Tun Chung, Chih-Chieh Kang, and Jeng-Feng Lin Department of Electrooptical Engineering, Southern Taiwan University Tainan, TAIWAN LED UNIFORM SURFACE LIGHT SOURCE WITH NO LIGHT GUIDE PLATE Introduction Experiment Results and discussions Conclusions REFERENCES Abstract In the rising global tide of energy saving and environmental protection, LED has become the backlighting source of choice for LCD displays. This is due to its advantages of being low power consumption, free of mercury, longer life, continuously improved luminous efficacy, and rapidly decreased price, etc. However, as the size and thickness of a backlight unit (BLU) becomes larger and thinner, the design of the indispensable components for an edge-type LED BLU―light-guide plate (LGP) also becomes more challenging and its manufacturing processes get more complicated and costly. Therefore the concept of edge-type LED BLUs with no LGP[1] exhibits significant competitive advantage over its adversaries: edge-type BLUs with LGP and direct-type BLUs as well in terms of manufacture process and cost. As for its implementation[1-3], in most cases side-emitting LEDs with narrow beam angle, such as ±20° for Luxeon Emitter, are demanded. But the use of side-emitting LEDs implies energy loss due to the multiple reflection of light inside the LED lamp reflection. To rectify this problem, we propose a slightly modified approach―replacing side-emitting LED with shell-type narrow beam LED, e.g., Nichia NSPW500, of which the half angle is within ±10°, illustrated by its radiation pattern[4], shown in Fig. 1. To examine the effectiveness of our proposed approach, An ASAP ray- tracing model for a 20-inch edge-type LED BLU with no LGP, as shown in Fig. 2, has been developed to perform the design work of illuminance uniformity for a LED BLU. With the concern of computation time in simulation, a truncated version of the model is implemented. It consists of 10 LEDs, five on each short side housed inside LED lamp reflectors, a bottom reflection sheet with bumpy structures, and a diffusion plate on-top. The inner surface of lamp reflector is taped with white reflector, whereas the surface of bottom reflector is kept to be of specular reflection. The dimension of the BLU is of 62.6 × 251.5× H mm, where H is the height of the BLU. In order to ensure the accuracy of optical simulation, an accurate BSDF model of ASAP for a white reflector has been constructed according to the measured data. As for the diffusion plate, a developed optical model based on Mie scattering is implemented. To simplify analysis, the LED is assumed to be a monochromatic light source with wavelength of 550 nm and the size of scatter inside the diffusion plate is assumed to be uniform instead of a size distribution function, though the scattering of light through a diffusion plate depends on particle size, volume fraction, the wavelength of incident light, and the relative refractive index between the scatters and the host media, etc[5]. Fig. 1. Radiation pattern of Nichia NSPW500. Fig. 2. (a) Schematic and (b) cross-section of proposed edge-type LED BLU with no LGP. Three sections of bumpy structures are constructed on the bottom reflector. Fig. 3. Simulation results. (a) hB = h/2, lB = lC/2 (b), hB = h/4, lB = lC/2 and, (c) hB = h/2, lB = 3lC/4. Fig. 4. Illumiance uniformity. Simulation results (a) without, and (b) with a diffusion plate. By using a shell-type narrow beam LED, we can implement the concept of an edge-type LED BLU without LGP. To achieve illuminance uniformity for a uniform backlight source, the optimal design parameters can be achieved through optical simulations. This demonstrates the feasibility of using our devised approach. However, these parameters can be varied by the size as well as the height of a BLU. And future work will focused on the problem of thinness for this structure. 【 1 】 Sakai, S., Mori, A., Ishiguchi, K., Kobauashi, K., Kokogawa, T., Sakamoto, T., and Yoneda, T., “A thin LED backlight system with high efficiency for backlighting 22-in. TFT-LCDs”, SID 04 Digest, (2004) pp 【 2 】 Chen, C. H. and Shieh, H. P. D., Inclined LED array for large-sized backlight system, SID 05 Digest, (2005) pp 【 3 】 Hung, C. P., Chen, W. S., Lin, J. H., and Li, W. Y., Novel design for LED lens and backlight system, (2007) IDMC07, pp 【 4 】 NICHIA Corporation, 【 5 】 Hsu, Y. C., Kang, C. C., and Lin, J. F., 3D Simulation of a LCD backlight diffuser using Monte Carlo ray- tracing modeling, in Proc ISNST, Tainan, (Nov. 2006) pp