OfficeServ 7200 Hardware Description Distribution ED01 English STM#121: OfficeServ 7200 Hardware Description Code : STM#120 OfficeServ 7200 Hardware Description Samsung Electronics Co., Ltd.

Contents Cabinet and Power Supply Processor Modules Voice Trunk Modules Subscriber Stations Data Modules Terminals © Samsung Electronics Co., Ltd.

Cabinet and Power Supply © Samsung Electronics Co., Ltd.

Cabinet Configuration Expansion Cabinet LCP only 8TRK,DLI,SLI,HYB WLI,MGI,WIM,4DSL 8TRK,DLI,SLI,HYB WLI,MGI,LIM,4DSL 8TRK,DLI,SLI,HYB,LIM TEPRI,WLI,MGI,4DSL 8TRK,DLI,SLI,HYB,LIM WLI,MGI,4DSL 8TRK,DLI,SLI,HYB,LIM WLI,MGI,4DSL MCP only 8TRK,DLI,SLI,HYB WLI,MGI,WIM,4DSL 8TRK,DLI,SLI,HYB WLI,MGI,LIM,4DSL 8TRK,DLI,SLI,HYB,LIM TEPRI,WLI,MGI,4DSL 8TRK,DLI,SLI,HYB,LIM TEPRI,WLI,MGI,4DSL 8TRK,DLI,SLI,HYB,LIM TEPRI,WLI,MGI,4DSL Access Cabinet © Samsung Electronics Co., Ltd.

Rear Side Configuration of Cabinet continue               Rear Side Configuration of Cabinet Function  External Rectifier Socket External DC power supply socket for PoE.  Power Switch Turn on/off the OfficeServ 7200 power.  Power Connection Connector between Basic Cabinet and Extension Cabinet The connector to supply the supplied power to the external cabinet.  Power Input/Output Connector The connector to connect power cable.  AC LED LED is turned on when AC power is entered.  DC LED LED is turned on when DC power is properly output.  Battery Connection Socket The socket to connect the external battery. © Samsung Electronics Co., Ltd.

PSU (Power Supply Unit) Features 1 PSU per chassis Mounted on back plane Supports 80 devices per chassis Power is controlled by a thermal sensor After 24hrs of cooling fan failure, PSU will stop ! © Samsung Electronics Co., Ltd.

Processor Boards © Samsung Electronics Co., Ltd.

MCP (Main Control Unit) Features Installed in slot 0 of main chassis 256 time slot switch matrix 1x smart media card slot 3x daughter module positions Memory backup switch 8 position DIP switch 1x internal MOH source MFM : Multi-Frequency Module RCM/RCM2 : R2 CID Module MIS : Miscellaneous MFM RCM MIS © Samsung Electronics Co., Ltd.

continue Capacity without Option board Capacity with Option board Items Specification No. of DTMF sender No. of DTMF receiver 4 channels Items No. of channel No. of DTMF sender Non limit No. of DTMF receiver 16 channels No. of R2/CID receiver 14 channels No. of R2 sender 29 channels Items No. of channel External music on hold 2 channels Internal music on hold 1 channel External page External loud bell External page dry contact Common dry contact © Samsung Electronics Co., Ltd.

continue Sets DIP switch S2 S3 Off CHARGE © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description LINK1~LINK3 Ports that connect the MCP with the LCP. MISC1~MISC2 Ports that connect external music sources, paging device, loud bell, common bell, or door bell. SmartMedia Port for installing the NAND-type flash memory. LAN Port for establishing the 10/100 BASE-T Ethernet connection. SIO UART port (for tests). RST Button for resetting the MCP board. RUN LED - Off: Power is not connected. - On: Booting - Blink: The Program is operating properly LAN LED - Off: MCP is not connected to LAN. - On: MCP is connected LAN. - Blink: MCP is transmitting or receiving Data through LAN port. SM LED - Off: The Smartmedia is not installed. - On: The SmartMedia is installed, however is not accessed. - Blink: The SmartMedia is installed and is being accessed. LCP LED - Off: There’s no message exchange between MCP and LCP. - On: Messages are being sent/received to/from the LCP. © Samsung Electronics Co., Ltd.

Daughter boards for MCP MFM (Multi-Frequency Module) Installed in any position on MCP module Only 1 per system 12 DSPs for DTMF and tone detection © Samsung Electronics Co., Ltd.

continue RCM (R2 CID Module) Installed on MCP module Only 1 per system R2 signalling send (30 channels) and receive (8 channels) or CID detection (14 channels) by DIP switch on RCM. RCM2 R2 signalling send ( channels) and receive (8 channels) or CID detection (14 channels) by DIP switch on RCM. © Samsung Electronics Co., Ltd.

continue MISC (Miscellaneous) Installed on MCP Only 1 per system 2x external MOH 1x external page 1x loud bell 1x common bell 1x dry contact © Samsung Electronics Co., Ltd.

continue Dry contact #1 (For common bell) Dry contact #2 (For external page) External Page Equipment Additional Page Equipment MISC 1 MISC 2 Dry contact #2 © Samsung Electronics Co., Ltd.

LCP (Local Control Processor) Features Installed in slot 0 expansion chassis 3x link cable RJ45 ports, for connection to MCP 2x status LEDs © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function LINK1~LINK3 Ports that connect the MCP with the LCP. SIO UART port(for tests). RST Button for resetting the LCP board. RUN LED This LED indicates the status of the LCP. - Off: Power is not connected. - On: Booting. - Blinking: Program in operation. MCP LED This LED indicates the status of signaling message processing. - Off: There’s no message exchange between MCP and LCP. - On: Messages are being sent/received to/from the MCP. © Samsung Electronics Co., Ltd.

Voice Trunk Modules © Samsung Electronics Co., Ltd.

Voice Trunk Module (TEPRI) Features Same as OS500 operation. Only installed in slots 3 – 5 of Access cabinet or slot 3 of Expansion cabinet. T1/E1 signals by programming. Resistor Terminations for T1 line(100 W) and E1 line(120 W). 8 position DIP switch. © Samsung Electronics Co., Ltd.

continue DIP switch Setting © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description T1/E1/PRI RST TEPRI T1/E1/PRI SIO SYNC ASI IPC TP1 LOS L2 CLK TP2 Front View Ports & LEDs Function Description T1/E1/PRI Ports that connect the T1/E1/PRI cable. SIO UART port (for tests). RST Button for resetting the TEPRI board. SYNC LED - On: Clocks are not synchronized when they interwork with the counterpart station. - Off: Clocks are synchronized when they interwork with the counterpart station. LOS LED - On: Signals have been lost. - Off: Signals have not been lost. AIS LED - On: The remote alarm has been generated. - Off: The remote alarm has not been generated. L2 LED - On: The PRI Layer2 is operating properly. - Off: The PRI Layer2 is operating abnormally. IPC LED - On: The board is interworking with the MCP/LCP. - Off: The board is not interworking with the MCP/LCP. CLK LED - On: The board has received the synchronization clock from the counterpart station. - Off: Using synchronous clock for internal clock. TP1 LED - This LED turns on once the T1 is established. TP2 LED - This LED turns on once the PRI is connected. © Samsung Electronics Co., Ltd.

Voice Trunk Module (8TRK) Features 8 trunk loop start module 8 caller ID path support Performs Polarity Reverse Sensing (PRS), (Option) Performs Metering Pulse Detection (MPD), (Option) © Samsung Electronics Co., Ltd.

continue Pin Assignment P1-P8 Port (RJ-45) Pin No. 1 2 3 4 5 6 7 8 Function - C.O. TIP C.O. RING © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description P1~P8 8TRK P1 P5 P2 P6 P3 P7 P4 P8 Ports & LEDs Function Description P1~P8 Trunk ports. P1~P8 LED These LEDs indicate the status of the ports. - Off: The trunk line is not being used. - On: The trunk line is being used. - Blink: The ring is being connected. © Samsung Electronics Co., Ltd.

Voice Trunk Module (4BRI) Features 8 ISND2 channels Slots 1 – 5 of any cabinet Max 10 cards – 80 channels © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description P1-T~P4-T 4BRI P1-T RUN P2-T P3-T P4-T P1-S P2-S P3-S P4-S ACT Ports & LEDs Function Description P1-T~P4-T Office (trunk) Port P1-S~P4-S Internal (station) Port RUN LED 4BRI Board Operation Status - Off: 4BRI board is abnormal or power is disconnected - On: 4BRI board is properly operated. ACT LED 4BRI Board LAYER1 SETUP Status - Off: LAYER1 SETUP Abnormal - On: LAYER1 SETUP Normal © Samsung Electronics Co., Ltd.

MGI (Media Gateway Interface) Features MGI2 – carrier module has NO MGI channels MGI2 daughter modules added to provide 4 – 16 channels. Installed in any subscriber slot. G.729,G.723.G.726.G.711 © Samsung Electronics Co., Ltd.

continue Option board Option board provide 4 channels. Option1 Option2 MGI2D Option3 Option2 Option1 © Samsung Electronics Co., Ltd.

Subscriber Stations © Samsung Electronics Co., Ltd.

Analog Station (8/16SLI) Features SLI (Subscriber Line Interface) Functions Ring generation DTMF/Dial pulse detection Hook on/off detection Tone generation Board types 8 SLI : 8 SLI ports 16 SLI : 16 SLI ports 16 MWSLI : 16 SLI with message wait Power fail transfer relays © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description P1~P8 8SLI P1 P5 P2 P6 P3 P7 P4 P8 16SLI P1/P9 P1 P9 P2/P10 P3/P111 P4/P12 P5/P13 P6/P14 P7/P15 P8/P16 P2 P10 P3 P11 P4 P12 P13 P5 P14 P6 P15 P7 P16 P8 Ports & LEDs Function Description P1~P8 Station ports for analog phones. P1~P8 LED or P1~P16 LED These LEDs indicate the operation status of the ports. - Off: The station is not being serviced. - On: The station is being serviced. © Samsung Electronics Co., Ltd.

continue Pin Assignment P1 port Ports from P2 to P8 Pin No. 1 2 3 4 5 6 7 8 Function PFT TIP RING - SLI 1 Ports from P2 to P8 Pin No. 1 2 3 4 5 6 7 8 Function - SLI 2 TIP RING © Samsung Electronics Co., Ltd.

Digital Station (8/16DLI) Features DLI (Digital Line Interface) Types 8 DLI : 8 DLI ports 2B+D 16 DLI : 16 DLI ports 1B+D Max 8 large display phones per module © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description P1~P8 or P1~P16 8DLI P1 P5 P2 P6 P3 P7 P4 P8 16DLI P1/P9 P1 P9 P2/P10 P3/P11 P4/P12 P5/P13 P6/P14 P7/P15 P8/P16 P2 P10 P3 P11 P4 P12 P13 P5 P14 P6 P15 P7 P16 P8 Ports & LEDs Function Description P1~P8 or P1~P16 Station ports of Samsung digital phones. P1~P16 LED These LEDs indicate the status of the ports. - Off: The station is not being used. - On: The station is being used. If the LED turns green, it shows that the P1-P8 is being used. If the LED turns red, it shows that the P9-P16 is being used. If the LED turns yellow, it shows that both of the ports are being used simultaneously. © Samsung Electronics Co., Ltd.

continue Pin Assignment Pin No. 1 2 3 4 5 6 7 8 Function - DLI 1 © Samsung Electronics Co., Ltd.

Hybrid Station (8HYB/8Combo) Features Ring generation DTMF/Dial pulse detection Hook on/off detection Tone generation Specifications 8 SLI ports 8 DLI ports © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description P1~P16(8HYB) P1~P16(8COMBO) Station ports of Samsung digital phones. P1~P16 LED (8HYB) These LEDs indicate the status of the ports. - Off: The station is not being used. - On: The station is being used. If the LED turns green, it shows that the P1-P8 is being used (Analog phone port). If the LED turns red, it shows that the P9-P16 is being used (Samsung digital phone port). If the LED turns yellow, it shows that both of the ports are being used while being connected to an analog phone and Samsung digital phone simultaneously. © Samsung Electronics Co., Ltd.

continue Pin Assignment Pin No. 1 2 3 4 5 6 7 8 Function - SLI 1 TIP/DLI SLI 1 RING/DLI © Samsung Electronics Co., Ltd.

Voice Mail System (SVMi-20E) Features Same position rules as station modules Default card has 4 ports Scalable to 20 ports? Modem daughter card (and yes, it works!) © Samsung Electronics Co., Ltd.

continue Front View Part Description LAN Interface Connector SIO VM1 VM2 VM3 HDD LAT LRT SDN PGD SVMi-20E RST Front View Part Description LAN Interface Connector The LAN interface connector is used for data transmission and database backup. It is also called as ‘LAN connector’ and mainly used for system file transmission (backup and restore) SVMi-20E backs up or restores data by using LAN provided by customer or by connecting to laptop computer or PC connected the relevant LAN connector. Serial Interface Connector Used to connect to PC. Reset Button(RST) If pushing this button, SVMi-20E system starts and the call in progress is disconnected. LED (Light Emitting Diode) VM1 When one or more ports are hooked on/off in the first 4 ports(1~4), it blinks. VM2 When one or more ports are hooked on/off in the second 4 ports (5~8), it blinks. VM3 When one or more ports are hooked on/off in the final 4 ports(9~12), it blinks. HDD If accessing to the hard disk driver, LCD blinks. LAT When the LAN port is run, LED is turned on into green color. LRT When transmitting data to LAN, LED is turned on into orange color. SDN This LED displays the system status. When the system driver is loaded, LED is turned on into red color, and if the loading is terminated, LED is turned into green color. PGD If the system power is normal, LED is turned on into green color. © Samsung Electronics Co., Ltd.

Data Modules © Samsung Electronics Co., Ltd.

Router Module (WIM) Features WIM : WAN Interface Module Functions Only 1 per system Only installed in slot 1 of main chassis 1x LAN port 2x WAN ports (RJ45) 1x WAN port (V.35 serial) 1x DMZ SIO for configuration WIMD – daughter board for VPN © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description DMZ WIM DMZ WAN1 LAN WAN2 SIO SERIAL RUN SERIALL RST Front View Ports & LEDs Function Description DMZ Internal port that does not need firewalls LAN Ethernet port connected with the Intranet SERIAL Port that connects the serial dedicated line that interworks with the V.35 WAN1, WAN2 WAN interface port that interworks with Ethernet of 10/100 BASE-T SIO UART port(for tests) RST Button for resetting the WIM module RUN LED - Off: The WIM board is in an abnormal status or the power is not being supplied. - On: The WIM board is operating properly. DMZ LED - Off: The link is not connected. - On: The link is operating. SERIAL LED WAN1, WAN2 LED LAN LED - Off: Link is not connected - On: Link is in operation © Samsung Electronics Co., Ltd.

continue WIM to LIM connection The Method of LAN port connection Managed LIM : Slot2 LIM with WIM Unmanaged LIM : Slot 3,4,5 Using the Ethernet port of the front panel, Through back panel, connect with the LIM board of slot 2. © Samsung Electronics Co., Ltd.

Switch Module (LIM/PLIM) LIM : LAN Interface Module Features Installed in slots 2 ~ 5 of any chassis Max 8 per system (128 ports) When in slot 2 of main chassis it’s a managed switch If in any other slot it’s unmanaged 16x 10/100 base T Ethernet ports PLIM provides the Power over Ethernet (PoE) function Functions Detects 10/100 BASE-T, or full/half duplex automatically. Offers the VLAN for supporting QoS. Functions as a switching hub. © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description P1~P16 LIM P1 P5 P2 P6 P3 P7 P4 P8 P9 P13 P10 P14 P11 P15 P12 P16 Front View Ports & LEDs Function Description P1~P16 Ports for connecting the Ethernet. Left LED of each port The LED indicates if the link is operating. - Blink: The link is operating. Right LED of each port The LED indicates if the port of 10/100 BASE-T is operating. - Off: The port of 10 BASE-T is operating. - On: The port of 100 BASE-Tx is operating. © Samsung Electronics Co., Ltd.

Wireless Modules © Samsung Electronics Co., Ltd.

Voice Application Module (4WLI) WLI : Wireless Line Interface Features Functions Voice decompression: G.711, G.729 Wireless specification: 802.11b WLAN Specifications Up to four APs. Simultaneous calling through up to four channels per AP. The maximum number of mobile station subscribers is 120. © Samsung Electronics Co., Ltd.

continue Front View Ports & LEDs Function Description P1~P4 4WLI P1 P2 P3 P4 RUN SW1 SW2 SW3 SIO Ports & LEDs Function Description P1~P4 Port that connects with the WBS24. SIO UART port (for tests). RUN LED This LED turns on when the wireless LAN operates. SW1~SW3 LED This LED turns on when the software task operates. © Samsung Electronics Co., Ltd.

Terminals © Samsung Electronics Co., Ltd.

Digital Phones DS-24SE DS4000 Series DS5000 Series DS2000 Series DS-5012L DS-5014D DS2000 Series DS-5021D DS-5038D DS-3020S © Samsung Electronics Co., Ltd.

IP Phones ITP5000 Series ITP5100 Series ITP-5012L ITP-5107S ITP-5121D © Samsung Electronics Co., Ltd.

AP (Access Point) Configuration WBS24 Basic WBS24 Combo MCP MGI LIM RJ45 RJ11 AC POWER LIM-MGI PC Configuration WBS24 Basic WBS24 Combo PDA SoftPhone MCP MGI LIM WIP Phone Laptop PC Data WIM LIM RJ45 RJ11 WLI PC LIM Coverage = 30m PDA SoftPhone MCP WLI WIP Phone Laptop PC Data WIM PLIM © Samsung Electronics Co., Ltd.

WLAN Phones Configuration © Samsung Electronics Co., Ltd.

Add on Module Features Station module type of digital phone where the programmable buttons and LEDs are expanded. AOM Types Connectable Phones DS-5064B AOM DS-5000 series digital phone DS-4014 AOM DS-4000 series digital phone DS-4064 AOM DS-24SE AOM DS-24SE digital phone DS-2024E AOM DS-2000 series digital phone DS-3020S AOM DS-3000 series digital phone © Samsung Electronics Co., Ltd.

Door Phone Interface Module Features Door Phone Interface Module (DPIM) connects door phones and door open/close devices with the OfficeServ 7200. © Samsung Electronics Co., Ltd.

KDB-D/S Features The KDB-D module is attached to the digital phones connected with the DLI board for use. The KDB-D enables a digital terminal to use one out of the two B channels received by another digital phone from the DLI board. © Samsung Electronics Co., Ltd.

Samsung Electronics Co., Ltd.