Patel Tejasvini D.(T-13CL225)

Slides:



Advertisements
Similar presentations
Theodolite: Introduction
Advertisements

Surveying I. Lecture 4..
Surveying I. Lecture 2..
Sz. Rózsa: Surveying I. – Lecture 2
Plane Table Mapping The power of triangles And Appropriate Technology.
Micrometer Sizes range from 0 to 1 inch up to 12 inches.
CE 260 SURVEYING CHAPTER 5.
S.H.H.S Building Construction
ENGINEERING SURVEYS DEFINITION Surveying has to do with the determination of location of points on or near the surface of the earth. It is the art/science.
1. Chose a location where you can see all other points of interest 2. Pace out the area so that you get a feel for what kind of scale you may use. 3. Set.
Faculty of Engineering Technology
Energy & Environment. What are these lines called and what are they used for? If this map has a scale of 1:25,000 what does this mean? They are called.
Harry Williams, Cartography1 Surveying Techniques I. The USGS supplies 1:24,000 scale maps for all the U.S. But detailed topography at larger scales is.
Faculty of Engineering Technology
CHAPTER 2 CHAIN SURVEYING Tape Measurements
Introduction to surveying
Surveying instruments
Compass surveying.
Sz. Rózsa: Surveying I. – Lecture 1
Surveying I. Lecture 3..
Surveying I. Lecture 13. Tacheometry.
REG231 – Basic Land Surveying
1.Chose a location where you can see all other points of interest 2.Pace out the area so that you get a feel for what kind of scale you may use. 3.Set.
Surveying Techniques I. The USGS supplies 1:24,000 scale maps for all the U.S. But detailed topography at larger scales is rare and/or.
TECHNIQUES IN BASIC SURVEYING
Chapter (5) Leveling Introduction:
COMPASS SURVEYING STUDY OF INSTRUMENTS AND AREA CALCULATION
Orthographic Multiview Projection Multiview Projection.
Dumpy Level Surveying Energy & Environment.
THEODOLITE SURVEYING THEODOLITE SURVEYING
CHAPTER 3 LINEAR MEASUREMENTS
Topic : Theodolite Traversing
SURVEYING PLANE TABLE SURVEYING 1. 2  Plane Tabling is a graphical method of surveying in which the field work and plotting are done simultaneously.
THEODOLITE SURVEYING THEODOLITE SURVEYING. THEODOLITE SURVEYING THEODOLITE SURVEYING.
Mahatma Gandhi Institute of Tech. Education and Research Center
PLANE TABLE SURVEYING NUST Institute of Civil Engineering/Engr Muhammad Ammar.
PLANE TABLE SURVEYING SURVEYING – I
INSTRUMENTS USED IN PLANE TABLE SURVEYING.
Civil Department. GROUP MEMBERS GROUP MEMBERS:- ENROLLMENT NO. NAME OF THE STUDENT BURHAN ADENWALA PRIYANK AGRAWAL TAMANNA.
Rampurwala Taher Z Panchal Deep S Shah Akash K Patel Apurv K Rathod Hardipsinh.
CIVIL DEPRATMENT.
Made by- Civil 3rd semester
VARIOUS METHODS OF PLANE TABLE SURVEYING
Compass Surveying.
GOVERNMENT ENGG. COLLEGE B.E Semester III :- Civil Engineering
In Compass survey chain or tape is used for linear measurements and compass is used for fixing direction. In compass freely suspended.
Under the guidance of Prof. S. Roy Chowdhury Prepared by. Anjan Mukherjee B.C.E-III, Sec-B2 Roll
CIVIL A [3 RD SEM ] TOPIC :- Plane Table Survey GROUP 1O ENROLLMENT NO  DARSHAN R MEHTA  KOMAL N MALVANIYA  HARDIK G MAKWANA.
SANKALCHAND PATEL COLLEGE OF ENGINEERING, VISNAGAR PLANE TABLE SURVEYING PREPARED BY: PATEL AVANI B PANDYA RUCHA H CHAUHAN.
BIRLA VISHWAKARMA MAHAVIDYALAYA
Handled by, R.PRADEEPA, M.E Assistant Professor, Department of Civil Engg, PITS.
Mr. Vedprakash Maralapalle, Asst. Professor
FACULTY OF ENGINEERING TECHNOLOGY AND RESERCH, TAJPORE, BARDOLI CIVIL ENGINEERING DEPARTMENT SURVEYING ( )
Surveying I. Lecture 3..
Surveying 1A (SVG 105) PLANE TABLE SURVEYING
Visit for more Learning Resources
Theodolite: Introduction
Topic: “Plane table surveying”…
SURVEYING Plane Table Survey
Theodolite: Introduction
Plane table surveying with contouring
Introduction Theodolite is used to measure the horizontal and vertical angles. Theodolite is more precise than magnetic compass. Magnetic compass measures.
COMPASS SURVEYING.
VADODARA INSTITUTE OF ENGINEERING
THEODOLITE TRAVERSING BY S N Nanaware
SURVEYING – II THEODOLITE
Unit 5. Levelling.
Unit 4. Plane Table Surveying
Leveling By : Parveen Kumar.
1.  Plane table is a graphical method of surveying in which the field works and the plotting is done simultaneously.  It is particularly adopting in.
Presentation transcript:

Patel Tejasvini D.(T-13CL225) SAL INSTITUTE OF TECHNOLOGY AND ENGEENIRING RESEARCH Ahmedabad B.E (3rd Semester)-Civil-Shift 2 December-2014 Group-3 Shah Disha R.(T-13CL247) Gosai Beran M.(T-13CL207) Chavda Hetal N.(T-13CL203) Patel Keval K.(T-13CL223) Patel Tejasvini D.(T-13CL225)

Plane Table Survey

Content Plane Table Surveying Principle Instruments setting up the plane table methods of plane tabling Advantages & Disadvantages sources of Errors.

Plane Table Surveying Plane Table Surveying is a graphical method of survey in which the field observations and plotting are done simultaneously. It is simple and cheaper than theodolite survey. It is most suitable for small scale maps. The plan is drawn by the surveyor in the field, while the area to be surveyed is before his eyes. Therefore, there is no possibility of omitting the necessary measurements.

Principle Of Plane Table Survey The principle of plane tabling is parallelism means, Principle: “All the rays drawn through various details should pass through the survey station.” The Position of plane table at each station must be identical, i.e. at each survey station the table must be oriented in the direction of magnetic north.

Principle Of Plane Table Survey

Equipments and Accessories for Plane Tabling The following instruments are used in plane table surveying. Equipments Plane Table Tripod Alidade

Equipments and Accessories for Plane Tabling Trough Compass Spirit level U-Fork with Plumb bob Water proof cover Drawing paper Pins Drawing accessories

Equipments Plane Table: The drawing board for plane tabling is made from well-seasoned wood with its upper surface exactly plane. It is normally rectangular in shape with size 75 cm x 60 cm It is mounted on a tripod and clamps are provided to fix it in any direction. The table can revolved about its vertical axis and can be clamped in any position, when necessary.

Plane Table

Plane Table

Tripod The plane table is mounted on a tripod The tripod is generally of open frame type, combined rigidity with lightness. The tripod may be made to fold for convenience of transportation. Tripod is provided with three foot screws at its top for leveling of the plane table.

Tripod

Alidade The alidade is useful for establishing a line of sight. Two Types of alidade are used. Simple alidade Telescopic alidade

Simple Alidade It is used for ordinary work It is generally consists of a gun metal or wooden rule with two vertical vanes at the ends. The eye-vane is provided with a narrow slit while the object vane is open and carries a horse hair. Both the slits, thus provide a definite line of sight which can be made to pass through the object to be sighted

Simple Alidade

Simple Alidade To draw the rays, one of the edge of alidade is beveled and this perfectly smooth working edge is known as the fiducially edge. The fiducially edge is graduated to facilitate the plotting of distances to a scale.

Telescopic Alidade The telescopic alidade is used when it is required to take inclined sights. It essentially consists of a small telescope with a level tube and graduated arc mounted on horizontal axis. It gives higher accuracy and more range of sights.

Telescopic Alidade

Telescopic Alidade

Accessories Trough Compass The trough compass is required for drawing the line showing magnetic meridian on the paper. It is used to orient the table to the magnetic meridian. When the freely suspended needle shows 00 at each end, a line is drawn on the drawing paper which represents the magnetic north.

Trough Compass

Spirit Level A Spirit Level is used for ascertaining If the table is properly level. The Table is leveled by placing the level on the board in two positions at right angles and getting the bubble central in both positions.

Spirit Level

U-Fork With Plumb bob U-fork with plumb bob is used for centering the table over the point or station occupied by the plane table when the plotted position of that point is already on the sheet. Also, in the beginning of the work, it is used for transferring the ground point on the sheet.

U-Fork With Plumb Bob

Water Proof Cover An umbrella is used to protect the drawing paper from rain.

Drawing Paper Drawing paper is used for plotting the ground details.

Setting Up the Plane table Fixing the plane table on the tripod stand Leveling the table Centering the table Marking the North-line Orientation Orientation by magnetic needle Orientation by backsighting

Methods Of Plane Tabling Radiation Intersection Traversing Resection Special Methods of Resection Compass Method Back-ray Method Two-point problem Three-point problem

Advantages and Disadvantages of Plane Table Surveying The plan is drawn by the surveyor himself while the area to be surveyed is before his eyes. Therefore, there is no possibility of omitting the necessary measurements. The surveyor Can compare the plotted work with the actual features of the area.

Advantages It is simple and cheaper than the theodolite survey. It is most suitable for small scale maps. No great skill is required to produce a satisfactory map and work may be entrusted to a subordinate. It is useful in magnetic areas where compass may not be used. The mistakes in writing field books are eliminated.

Advantage

Disadvantages Disadvantages (Limitations): It is not intended for very accurate work. It is not suitable in monsoon. It is essentially a tropical instrument. Due to heaviness, it is inconvenient to transport. Since there are so many accessories, there is likelihood of them being lost.

Disadvantage

Sources of Errors Instrumental Errors Personal Errors Errors of plotting

Thank You