Keith Clark NSM VRF Commercial VRF

What’s Different About Our Ductless Products? Ductless Mini-Split Technology Not Much

Market Overview – North America Residential Mini-Splits All Distribution VRF in North America All Distribution

Single Zone Systems Cooling Only 9K-36K Btu/h Heat Pump 9K-36K Btu/h Solar Hybrid 12K-18K Btu/h Product Offering Overview Multi Zone Systems – Flex-Match Heat Pump 18K-42K Btu/h Single Zone Large Capacity Systems – U-Match Heat Pump 18K-48K Btu/h

Internal Components – Outdoor Unit 2-Stage Compressor Electronic Expansion Valve Inverter Compressor, Condenser, and Evap. Fan Motor PCB operating range up to 185°F Temp Resistant Axial Fan

Internal Components Linear High Volume Fan High Efficiency Coil with Optimized Piping Design Integrated Base and Water Tray Inverter Fan Motor

Standard Features I Feel Intelligent auto-restart Comfortable sleeping mode Wide angle swing Independent dehumidifying Pre-heat mode (Anti-cold wind) Wide working temp Cooling temp. range is 0 ℉ (-18 ℃ ) to 115 ℉ (46 ℃ ) Heating temp. range is -4 ℉ (-20 ℃ ) to 75 ℉ (24 ℃ ) Optional Features Auto clean Cold plasma Health filter Wired control Hidden Display Backlit Double 8 Display

Single zone systems are 1 to 1 matched sets with Wall Hung indoor unit only. Single Zone Systems Simple installation Flare connections Pre-charged condenser Minimum maximum pipe length.

Solar Hybrid system is an inverter heat pump and can be fully powered with 1150 Watts from solar panels Solar Hybrid System

Flex-Match Offering – 2 to 5 Zones Mix and match indoor styles

Flex Match Matrix

U-Match – Large Capacity Single Zone 1 to 1 Match - Cassette, Ducted, or Floor Ceiling type indoor unit

All indoor units come with wireless remote control (except ducted units) Ducted units come with wired controller All indoor units can be connected to wired controller but may still use remote Wired controllers use 18 gauge thermostat wire Controls

Nomenclature Nomenclature can help quickly determine if OU and IU are compatible.

Systems are designed for optimum performance within specified parameters Installation Considerations Multi zone systems use the same specifications for pipe length as single zone systems. There can be slight variations in the specification tables.

Flex-Match Piping Flex-Match provides long piping connections for easier installation. Max pipe length: 263 ft. Max height dif. BTW indoor units: 25 ft. Max height dif. BTW outdoor and indoor units: 50 ft. Max length from outdoor to farthest indoor: 66 ft. Y-Branch Connector 4 service valves for easy installation

Invest in the Right Tools - Doing the job right is nearly impossible if you don’t have the right tools. Installation Tools Flare Nut Torque Wrench – Torqueing to proper specs is essential to a quality installation. Otherwise, leaks can occur over time with expansion and contraction. Multi-Meter with Diode Setting and Needle Probes – The ability to check diode functionality is essential to the troubleshooting process. Standard meter probes cannot get into small harness casings. 45° Flaring Tool - Mini-splits use flare connections. Systems only equipped with a small strainer to keep large debris out of the compressor. We do not allow soldering because debris can plug the strainer or damage the compressor. We do not allow filter dryers. SC440 45° Orbital Flaring Tool Flare Nut Torque Wrench Set

Installation Step-By-Step STEP 1 - Mount Condenser STEP 2 - Mount Indoor Unit STEP 3 - Connect Piping, Wiring & Drain STEP 4 - Torque Flare Fittings STEP 5 - Nitrogen & Bubble Leak Test STEP 6 - Vacuum Test STEP 7 - Open Service Valves and Test Operation STEP 8 - Cover Lines Installation Techniques

Installation techniques are basically the same for all residential and light commercial products. There are several industry companies making products that cater to the ductless market. We are partnering with some as “Accessory Partners” to assist with installations and provide technical expertise.

Troubleshooting Standard Questions: 1.Is the product registered for warranty? 2.Have you been through Nortek ductless training? 3.What is the nature of problem? 4.Does your indoor unit match outdoor unit? 5.Did you remove plastic plug in line set? 6.Did you purge with nitrogen and bubble leak test? 7.Did you pull a sufficient vacuum and leak test? 8.Is wiring uniform? 9.Is power supply appropriate and sufficient? 10.Are the IU and OU communicating? 11.Is piping within minimum maximum allowable lengths? 12.Did you add refrigerant, if so, how much? 13.Are you getting an error code? 14.Did you power unit before opening the service valves? 15.Did you use a 45° flaring tool? 16.Did you use a flare nut torque wrench?

Preventative maintenance for reliable system performance. Cleaning and Maintenance Variety of filters available from Nortek.

Training Facilities Nortek Global HVAC O’Fallon, MO Coming Soon: United Kingdom Belgium France

Internal Technical and Product Support Nortek Global HVAC O’Fallon, MO Technical Service Department Customer Service Department Sales Department Engineering Department Gree Engineering Support U.S. based engineer for 1 year Parts Inventory (Warranty & Service) Nortek Distributors Training Facilities Nortek Global HVAC O’Fallon, MO “Accessory Partners” Aligned with manufacturers to support installations and service of equipment Additional Support Catalogs Websites Installation Manuals Service Manuals App support (future) Primary Support

Thank You