Schutzvermerk nach DIN 34 beachten Handling 2 XControl XC600 XC600: Handling

Schutzvermerk nach DIN 34 beachten XC600: Assembly

Schutzvermerk nach DIN 34 beachten Address setting of the optional modules

Schutzvermerk nach DIN 34 beachten Comfortable diagnosis and handling even without programming tool or external visualisation 4 lines with 12 digits Choice of menue by turning 1 Confirm by pushing 2 Cursor blinks XControl: Display + Menu selection button

Schutzvermerk nach DIN 34 beachten PACK_8=ON HAUBE_2=AUF AUSSCHUSS=7 Diagnosis Program Receipt Device System Back Main Menu User-specific Display Basic menue Turn Push XControl: The Menus

Schutzvermerk nach DIN 34 beachten ! ! = non-acknoledged event PLC mode Loaded program Informed at a glance Push: To main menu Turn: To user-specific display Position Function selector switch S = Stop P = Run-P R = Run XControl: The Basic Menu

Schutzvermerk nach DIN 34 beachten Control sends strings to display 3 When programming: Choice of important variables, definition of strings 1 XSoft PACK_8=ON HAUBE_2=AUF AUSSCHUSS=7 Within each control cycle: interrogation of chosen variables 2 Actual and specific information at a glance XControl: User-specific display

Schutzvermerk nach DIN 34 beachten Displays errors and events Reset, Copy, aktivate, Load, Delete Define IP address, date/time, security, language, hardware configuration, software version Shut down, new start Back to basic menu Diagnosis Program Receipt Device System Back Logic menu paths: Quick finding without manual XControl: Main menu

Schutzvermerk nach DIN 34 beachten Error diagnosis: All non-acknoledged program errors are shown with time of occurance Battery empty, hardware module missing, program missing … List of events: Has the program been running without problems? Was it stopped or started? When was that? Starts / Stops Strong support while commissioning, servicing and operating XControl: Menu diagnosis

Schutzvermerk nach DIN 34 beachten INTERNAL EXTERNAL RAM Compact Flash (Plug-in at operation module) Flash Disk (Hard memory on CPU module) Activated program / receipt ACTIVATE LOAD Program / receipt RUN / RUN-P Simple and safe data management and program starting COPY Loaded program / receipt Start STOP Program / recipe XControl: Menus „Program“ und „Recipe“

Schutzvermerk nach DIN 34 beachten Activate Password Security Function selector switch at RUN Device Activating password via menus + Securing after commissioning Protection against unautorized menu manipulation Access only to Basic Menu and User-specific Menu “Lock switch”: Protection against unauthorized swich operation Display shows: “Function selector swich at RUN!” Protection against unauthorized programming Programming only with switch position RUN-P XControl: Security

Schutzvermerk nach DIN 34 beachten When performing a RESET some data is to be put back to its initial values while other data shall maintain their values Example: Feed data of a shaft Example: Statistic data... are maintained... are reset VAR Persistant... are maintained... are reset... are maintained VAR Retain PersistantVAR Retain WARM COLD Safe starts through correct initialization STOP RUN M-RES 1 2 Within XSoft variables are declared precisely 3 Resets during operation bring about the desired initialization Or power cycle XControl: Menu „Program“ – Reset functionality

Schutzvermerk nach DIN 34 beachten SECURITY Define password Other network participants GATEWAYDefine IP address IP ADDRESS Definition as network participant SUBNETMASK NAME SOFTWARE Interrogation of actual version DATE / TIME LANGUAGE (English, German, Italian, French) Efficient configuration and interrogation HARDWARE Interrogation of actual modules Router XControl: Menu „Device“

Schutzvermerk nach DIN 34 beachten Operation Removal or malfunction of a hardware module TimeCommissioning AUTOcONFIG = OFF “Freeze” of nominal configuration Error reported SF-LED shows red Perfect supervision of hardware XControl: Menu „Device“ – Hardware configuration