Landscape Irrigation Based upon the book Rain Bird Irrigation Design Manual.

Slides:



Advertisements
Similar presentations
Surge Pressure Computations
Advertisements

Fire Apparatus Pump Theory
PUMPING SYSTEMS BASICS
BLM National Training Center PIPE MATERIALS SELECTION.
R. Allen Straw Area Specialist SW VA AREC Virginia Cooperative Extension Irrigation Basics.
Cycle Stop Valves 1” through 16” 1 GPM to 10,000 GPM.
Booster System Basics: Constant Speed Systems
Pipeline Hydraulics.
Chapter 3.1 Storm Drainage Sizing. Building Drain & Sewer  Building Drain —That part of the lowest piping of a drainage system that receives the discharge.
1 Math Questions. 2 Length x Width x Water Depth = cubic feet.
Fluids & Bernoulli’s Equation Chapter Flow of Fluids There are two types of flow that fluids can undergo; Laminar flow Turbulent flow.
Operation of Centrifugal pump
Flushing. Annual flushing is enough for many systems, but some water and emitter combinations require almost daily flushing to control clogging. If frequent.
Pump Basics. Centrifugal Pumps From the Center of a Circle RADIAL DIRECTION To the Outside of a Circle A machine for moving fluid by accelerating the.
Landscape Irrigation Slide Set and Narrative Provided by Dr. Brian G. Leib Dr. John Buchanan Biosystems Engineering & Environmental Science Agricultural.
Installing & Maintaining Irrigation Systems Ms. Gripshover Landscaping Unit 15.
Basic Hydraulics Irrigation.
What is it?. Fluid Mechanics  The study of fluids and the forces on them.  What are fluids?
Irrigation Pipe.
Piping Systems.
Steel Pipe Plumbing Systems
Hydraulic Power.
WATER PIPING DESIGN FOR A RESIDENCE In the packet is a floor plan of a residence with water supply piping shown. Follow the process as a step by step.
Pipe Sizing Sizing Gas Pipe for Low-Pressure Systems
Installed Gain as a Control Valve Sizing Criteria Jon Monsen, Ph.D., P.E.
Micro Design. System Capacity D = gross application for what ever time period ( hrs, day or days) T= hours in time period used to decide “D” (max.
NFPA 31 Standard for the installation of Oil- Burning Equipment
Hydraulic Power Hydraulics
Pumps and Lift Stations. Background Fluid Moving Equipment Fluids are moved through flow systems using pumps, fans, blowers, and compressors. Such devices.
Micro Design. System Capacity Crop Water Needs Example Calculate capacity required for a proposed 1 ac. Micro irrigation system on Vegetables.
TEC 4607 Wind and Hydro Power Technologies Fall 2011.
Landscape Irrigation Based upon the book Rain Bird Irrigation Design Manual.
Unit Conversions. Dimensions Length Flow Volume Pressure Power.
Why is resource assessment important? It wont work without the resource! (Lawn ornament) It will not provide a return on investment without working! You.
HVACR116 – Trade Skills Longest length method.
HVACR116 – Trade Skills Pipe Sizing Sizing Gas Pipe for Low-Pressure Systems.
Washington University ChE 433 Digital Process Control Laboratory Fluid Statics & Dynamics Lecture.
CBE 150A – Transport Spring Semester 2014 Other Friction Losses Valves and Fittings.
Pipe Sizing Chart Exercise Based upon the tables in the book Rain Bird Irrigation Design Manual.
Sizing Variable Flow Piping – An Opportunity for Reducing Energy
Chapter 2 Lecture Basic Chemistry Fourth Edition Chapter 2 Measurements 2.7 Problem Solving Using Unit Conversions Learning Goal Use conversion factors.
Microhydro Flow, nozzles. Site Assessment: Flow 5-gallon bucket –Small stream, small waterfall Float –Larger, flat, uniform stream V-notch Weir Rectangular.
Available Water Flow Meter Size Typical flow depending on size
Hydraulics is defined as the study of fluid behavior, at rest and in motion Properly designed piping with sound hydraulics can: - Greatly reduce maintenance.
Volume: Descriptions, Calculations & Industrial Applications
Water Management Water is an important natural resource that requires proper management. Appropriate flow rate, pressure, and water quality are necessary.
Based upon the book Rain Bird Irrigation Design Manual
Friction Loss Tutorial Used in conjunction with the Friction Loss Check Sheet and any Irrigation Plan.
Irrigation System for Home Landscape Developed by: Dr. Teri Hamlin Georgia Department of Education.
Chapter 1: Dimensional Analysis
Hydraulic Power © 2012 Project Lead The Way, Inc.Principles of Engineering.
IRRIGATION SYSTEMS. OBJECTIVES 1. Describe irrigation & its purpose 2. Explain preparation for irrigation systems 3. Calculate GPM 4. Identify & explain.
Tips on how to winterize your lawn sprinkler system Benefits of using Lawn Sprinkler Systems.
Irrigation Systems and Components. Overview Types Layout Components Hydraulics Design Considerations.
ATP FOAM SYSTEM Engine 438 Ansul / Rockwood Model B2 400 GPM Around The Pump Foam System.
Learning for Water wehelptwo.com
Domestic Hot Water Recirculation Design
Sensors and Detectors - 1
Tips on how to install irrigation systems
WATER DEMAND (Chapter 24)
Customary Units of Measure
2018 SHADE Conference “Fundamentals (Keys) of Basic Irrigation Design”
Find: max L [ft] 470 1,330 1,780 2,220 Pmin=50 [psi] hP=130 [ft] tank
Find: Q gal min 1,600 1,800 2,000 2,200 Δh pipe entrance fresh water h
Find: Phome [psi] 40 C) 60 B) 50 D) 70 ft s v=5 C=100
Find: QBE gal min 2, A F B Pipe AB BC CD DE EF FA BE C
Chapter 2 Measurements 2.7 Problem Solving Using Unit Conversions
Mathematics of Air Filtration
Presentation transcript:

Landscape Irrigation Based upon the book Rain Bird Irrigation Design Manual

Determine the Available Flow 3 common methods Stopwatch/meter method 5 gallon bucket/stopwatch method Flow meter method

Stopwatch/Meter Method Locate the first hose bibb in line along the service line Usually has a “shut-off” valve for the house Open the hose bibb Take a water meter reading In one minute take a second reading from the meter

Stopwatch/Meter Method Determine the difference in the two readings If the meter reads in gallons – you have the flow If the meter reads in cubic feet (cu.ft.) you must convert to gallons per minute

Conversion Cu.Ft. to GPM 1 Cu.Ft. of water equals gallons 1 Cu.Ft. = gal. So… Multiply the number of cubic feet from the meter reading times gal/cu.ft. Ex.: 1.55 cu.ft. x gal/cu.ft. = 11.6 gal/min. This answer is in gallons per minute

Conversion Cu.Ft. to GPM Since the reading was taken after one minute – the answer is in gpm or 11.6 gpm If the reading was taken after 2 min. – divide by 2… And so on….

5 Gallon Bucket/Stopwatch Method Locate that same first hose bibb Open the hose bibb Stick the bucket under the bibb into the flow Fill the bucket and time how long it takes in seconds

5 Gallon Bucket/Stopwatch Method Here’s the arithmetic: 60 seconds x 5 gallons = # gpm Ex. 60 seconds x 5 gallons = 12 gpm or (60 x 5) ÷ 25 = 300÷25 = 12 gpm 1 minute time in seconds 25 seconds

Flow Meter Method Locate that same first hose bibb – again Attach a “flow meter” to the hose bibb Open the bibb and take the reading – just that simple You also get a static pressure reading

OK… So we’ve established the flow… And we’ve established the static pressure… And we’re using the worst case too…

And… With a bit of effort we can determine the : Water meter size – 5/8”, 3/4”, 1”, 1-1/2” & 2” Service line type, size and length Water main type, size and length All of which can be limiting factors for the design

And then… We take a look at those three “rules of thumb”

Available Flow Rules These 3 “rules” determine safe flows through the water meter, service line and water main Know these inside and out!

Rule #1 … Water Meter Pressure Rule or the “10% Rule” Friction loss through the water meter must never exceed 10% of the static pressure on the site Helps prevent heavy pressure loss in the system

Rule #2… Water Meter Flow Rule Safe flow through a water meter should never exceed 75% of the maximum flow of the water meter This rule is designed to prevent excess demand on the water meter

Rule #3… Safe Velocity Rule or the “75% Rule” Maximum safe velocity through the service line should never exceed 5 fps for PVC pipe and 7.5 fps for metal pipe Designed to reduce damage to pipe, fittings and valves caused by excess velocities

What if…? We have a static pressure of 72 psi (WCS) A 1” water meter A 1” Type K copper service with a 10’ rise What is our available flow? In other words—”how many gallons per minute do we have?” WCS = worst case scenario

Rule #1… “10% Rule” How much static pressure can we loose from the water meter? 7.2 or 6.9 psi (if not in the table, round down to the next lowest number in the table for worst case) What flow does that give us? Or how many gallons per minute (gpm) are available?

Water Meter Table Find the correct meter size Locate the correct pressure Locate the flow 34 gpm is the available flow for “Rule #1”

Rule #2… “75% Rule” How much flow (gpm) can we safely get from the water meter? The “75% Rule” will tell us that What flow does that give us? Or how many gallons per minute (gpm) are available?

Water Meter Table Find the correct meter size Locate the maximum flow of the meter Determine 75% of the maximum flow 36 gpm is the available flow for “Rule #2”

Rule #3… “Safe Velocity Rule” Based on the industry standard for safe velocity in pipe, what is the maximum safe flow through 1” Type K copper?

Pipe Table Find the correct pipe type & size Locate the maximum safe velocity Determine the maximum flow 18 gpm is the available flow for “Rule #3”

The Available Flow Rules Give Us Rule #1 – “10% Rule” gives us 34 gpm Rule #2 – “75% Rule” gives us 36 gpm and Rule #3 – “Safe Velocity Rule” gives us 18 gpm

So… Which rule produces the limiting factor? Rule #3 Which element is that? Type K copper service line What is the available flow? 18 gpm

Moving Right Along.... We’ve establish all of those little details like: Static pressure…and Water meter size…and Service line type, size Any of which can be limiting factors… Giving us the available flow….

The Beginnings of the Design The available flow tells us what? Depending on their individual flows, we now know how many sprinklers we can run at any one time No more guessing!

What if…? We have a static pressure of 68 psi (WCS) A 3/4” water meter A 1-1/4” PE pipe city main with a 10’ rise up to the water meter A 1” Sch 40 PVC service line at 38’ from the meter to the house What is our available flow?

Rule #1… “10% Rule” How much static pressure can we loose from the water meter? 6.8 or 6.5 psi (if not in the table, round down to the next lowest number in the table for worst case) What flow does that give us? Or how many gallons per minute (gpm) are available?

Water Meter Table Find the correct meter size Locate the correct pressure Locate the flow 20 gpm is the available flow for “Rule #1”

Rule #2… “75% Rule” How much flow (gpm) can we safely get from the water meter? The “75% Rule” will tell us that What flow does that give us? Or how many gallons per minute (gpm) are available?

Water Meter Table Find the correct meter size Locate the maximum flow of the meter Determine 75% of the maximum flow 22 gpm is the available flow for “Rule #2”

Rule #3… “Safe Velocity Rule” Based on the industry standard for safe velocity in pipe, what is the maximum safe flow through 1-1/4” Polyethylene pipe?

Pipe Table Find the correct pipe type & size Locate the maximum safe velocity Determine the maximum flow 22 gpm is the available flow for “Rule #3a”

Rule #3… “Safe Velocity Rule” Based on the industry standard for safe velocity in pipe, what is the maximum safe flow through 1” Sch 40 PVC? Yup, it’s still “Rule #3” but we can call it “Rule #3b”

Pipe Table Find the correct pipe type & size Locate the maximum safe velocity Determine the maximum flow 12 gpm is the available flow for “Rule #3b”

The Available Flow Rules Give Us Rule #1 – “10% Rule” gives us 20 gpm Rule #2 – “75% Rule” gives us 22 gpm Rule #3a – “Safe Velocity Rule” gives us 22 gpm Rule #3a – “Safe Velocity Rule” gives us 12 gpm

So… Which rule produces the limiting factor? Rule #3b Which element is that? Sch 40 PVC service line What is the available flow? 18 gpm