Robertshaw Millivolt Troubleshooting Guide Gas Products

Slides:

Advertisements

Similar presentations

Residential Gas – Honeywell Valve - Thermopile Powered Series 300/301

Advertisements

Electricity The Quick Version.

Breadboard Power bus + (red) and – (blue) on left and right of breadboard abcde (green) are all connected in a row fghij (yellow) are all connected in.

Charging System Tests & Voltage information Checking the charging system with just a volt meter.

Master Jet Atmospheric Fryers The flame rides two inches above the burner manifold in an atmospheric fryer.

Understanding Electrical TransmissionDemonstration C2 A Guide to the National Grid Transmission Model Demonstration C2 Why are high voltages used for transmission?

Heating Control Devices

Bellwork TRUE/FALSE concerning Lab Safety: If a student drops an alcohol thermometer, they should stop, drop, and roll.

Millivolt Troubleshooting Guide Gas Products NOVA SIT Valves 1) Thermocouple Millivolt Check 2) Safety Magnet Testing 3) Thermopile Millivolt Check 4)

Register Digital Multimeter Usage Click Register to begin the course.

Cells have positive and negative electrodes.

HVAC121 – Gas Heat Flame Rectification.

7.3.2 Student Book © 2005 Propane Education & Research CouncilPage Identifying the Components and Operating Characteristics of Electronic Ignition.

Gas Furnace Controls Part 4.

PHSAUTOMOTIVESALSPHSAUTOMOTIVESALS Charging System tests & Voltage information Checking the charging system with just a volt meter.

California Friendly ® Landscape Training Irrigation System Troubleshooting The Metropolitan Water District of Southern California and the Family of Southern.

Lesson 23 AC Source Tx AC Thèvenin

SERIES AND PARALLEL CIRCUITS. Circuits  Provides a path for electricity to travel  Similar to water pipes in your house  Because of the voltage of.

TEST METER OPERATION. Electrical Test Instruments Analog Or Digital Voltmeters – Measuring Potential Difference Ammeters – Measuring Current Flow – Clamp.

Register Digital Multimeter Usage Click Register to begin the course.

Gas Furnace Controls Part 2.

Chapter 7. Voltage Remember: Atoms are in EVERYTHING and they are made up of equal amounts of positive and negative charges. Battery: uses chemical energy.

SERIES – PARALLEL DC CIRCUITS INCLUDING BASIC COMBINATION CIRCUITS Jimmie Fouts Houston County Career Academy.

Register Digital Multimeter Usage Click Register to begin the course.

Electrical Electricity Fuses Relays Solenoids Electrical Testing

Gas Furnace Planned Maintenance

7.4.1 Student Book © 2005 Propane Education & Research CouncilPage Identifying the Operating Characteristics of Circuit Control Devices, Electromagnetic.

 Four Components of a circuit  Power supply  Conductor  Load device  Controlling device  Power Supply  Generator  Line source (wall outlet)  Transformer.

Do Now Describe what you think happens electrically when you dim a light.

7.1.3 Student Book © 2005 Propane Education & Research CouncilPage Applying a Systems Approach to Gas Appliance Troubleshooting Troubleshooting.

Integrated Science Unit 3, Chapter 7.

Meter Accuracy DC Volts ±(0.1% of the reading + 1 digit) DC Amps

Speaker Foundations of Technology Speaker © 2013 International Technology and Engineering Educators Association, STEM  Center for Teaching and Learning™

Register Digital Multimeter Usage Click Register to begin the course.

1 Basic Electrical Series and Parallel Circuits. 2 Introduction So far we have looked at circuits that have one path for electricity to go as well as.

E2 Motors and Motor Starting

Bellringer A standard household outlet has a voltage of what?

Why Maintenance Tasks are Important Produced by Joe Marchese.

Basic Electrical Contactors.

E1 – Electrical Fundamentals

1 HVAC122 - Gas Gas Valves. 2 Solenoid Gas Valves The solenoid gas valve is the simplest of all valves. This valve has an electrical magnetic coil which.

How an NPN Transistor Works

Page A5 Schematic Analysis for Sequence of Operation (AUTOMATIC Spark Ignition System)

In this lesson, you will learn how to set up a Digital Multimeter (DMM) to perform various measurements Click on each question to learn more How is the.

LCD Wiring Diagram Presentation B / B.

 Measurement of difference in potential energy between 2 locations in a circuit.  Also called potential difference  Measured in volts (V)  Drives.

BASIC ELECTRICITY AND MAGNETISM

Jag Mark Name 4 factors that can affect the resistance of a current?

E1 – Electrical Fundamentals

E2 Motors and Motor Starting

Operating a Amp – Volt – Ohm Meter

ELECTRICAL QUANTITIES IN CIRCUITS

Principles & Applications

Water Heater Repair – What to Do When You Get No Hot Water?

Gas Furnace Controls Part 1.

Using DMMs Part 2.

E2 Motors and Motor Starting

Figure 12.2 The signal voltage from a throttle position increases as the throttle is opened because the wiper arm is closer to the 5-volt reference.

Is there anything we can do to keep from going into this state?

How an NPN Transistor Works

Paul Chapple Manager Technical & Sales Support

Electronics Current Practice Problems LabRat Scientific © 2018.

THROTTLE POSITION (TP) SENSORS

Presentation transcript:

Robertshaw Millivolt Troubleshooting Guide Gas Products 1) Safety Magnet Testing 2) Thermopile Millivolt Check 3) Circuit Millivolt Check 4) Valve Operating Head Test

Electromagnet power unit (EPU) testing Set meter to Ohms for this test To take an Ohms reading on a safety magnet, remove EPU wire from the valve. Place one meter lead to the EPU wire spade and one to TP Good reading is 0 to 13 Ohms. If the reading is higher,magnet is defective therefore Change the Valve - Do not try to repair. Good Reading

Thermopile Millivolt Check Symptom - Intermittent shutdown or main burner will not light with on/off switch. Set meter to Volts DC / Millivolts Place on lead to TP/TH & TP Thermopile Output- MAIN BURNER OFF : 325 mv minimum required for system to operate consistently. If lower than 325 mv, change the thermopile.

Thermopile Millivolt Check Symptom - Intermittent shutdown or main burner will not light with on/off switch. Thermopile Output- MAIN BURNER ON: 110 mv minimum required for system to operate consistently. If lower than 110 mv, conduct valve operating head test. If valve proves good, change the thermopile.

Circuit Millivolt Check Symptom - Intermittent shutdown or main burner will not light with on/off switch. The Thermopile, energized by the pilot flame, generates sufficient power to operate the gas valve and on/off switch. Voltage drop across the switch terminals Burner on: 35 mv or less. Set meter to MV or Volts DC Place one lead to TP/TH and place one lead to TH *If higher than 35mv check connections and switch.

Valve Operating Head Test Symptom - Intermittent shutdown or main burner fails when burner switch or thermostat is turned on. Before conducting this test, disconnect all leads from valve. Set meter to Ohms for this test. One lead to TH/TP and one to TP 0 – 10.9 Ohms Good Infinite ohms (bad) One lead to TP and one to TH 1.5 – 1.7 Ohms Good Infinite ohms (bad)

Circuit Millivolt Check Symptom - Intermittent shutdown or main burner will not light with on/off switch. The Thermopile, energized by the pilot flame, generates sufficient power to operate the gas valve and on/off switch. Set meter to Ohms Place one lead to each spade switch in on position *If higher than 0.3 ohms replace switch