Common Mode Rejection Ratio

Slides:



Advertisements
Similar presentations
Operational Amplifier
Advertisements

Operational Amplifiers
Operational Amplifiers 1. Copyright  2004 by Oxford University Press, Inc. Microelectronic Circuits - Fifth Edition Sedra/Smith2 Figure 2.1 Circuit symbol.
Lecture 4: Signal Conditioning
Summing Amplifier -+-+ RFRF R4R4 + IFIF I4I4 VoVo R3R3 + I3I3 V3V3 V4V4 R2R2 + I2I2 V2V2 R1R1 + I1I1 V1V1 RLRL V id.
CHAPTER 3 Measurement Systems with Electrical Signals
Chapter 11 Operational Amplifiers and Applications
CHAPTER 1: INTRODUCTION TO OPERATIONAL AMPLIFIERS
Ref:080114HKNOperational Amplifier1 Lecture 1 Op-Amp Introduction of Operation Amplifier (Op- Amp) Analysis of ideal Op-Amp applications Comparison of.
Operational Amplifiers (Op Amps) Discussion D3.1.
Operational Amplifier
Operational Amplifiers
Operational Amplifiers (Op Amps) Discussion D3.1.
PH4705/ET4305: Instrumentation Amp Our sensor will be connected to some kind of measurement system either directly, diag. 1, or as a bridge circuit diag.
Instrumentation Amplifier
Lecture II: Linear Applications of Opamp
Introduction to Op Amps
ENTC 4350 BIOMEDICAL INSTRUMENTATION I BASIC DIFFERENTIAL AMPLIFIER.
Chapter 8 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Introduction to Op Amp Circuits ELEC 121. April 2004ELEC 121 Op Amps2 Basic Op-Amp The op-amp is a differential amplifier with a very high open loop gain.
Analog Electronics Lecture 5.
Analogue Electronics II EMT 212/4
Instrumentation for Scientists
Chapter 8 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
09/16/2010© 2010 NTUST Today Course overview and information.
Differential Amplifier
Electronics Fundamentals 8 th edition Floyd/Buchla © 2010 Pearson Education, Upper Saddle River, NJ All Rights Reserved. chapter 18 electronics.
© 2012 Pearson Education. Upper Saddle River, NJ, All rights reserved. Electronic Devices, 9th edition Thomas L. Floyd Electronic Devices Ninth.
Differential Amplifiers.  What is a Differential Amplifier ? Some Definitions and Symbols  Differential-mode input voltage, v ID, is the voltage difference.
Lecture 1 Op-Amp Introduction of Operation Amplifier (Op- Amp) Analysis of ideal Op-Amp applications Comparison of ideal and non-ideal Op-Amp Non-ideal.
Microelectronic Circuits, Sixth Edition Sedra/Smith Copyright © 2010 by Oxford University Press, Inc. C H A P T E R 02 Operational Amplifiers.
10/11/2015 Operational Amplifier Characterization Chapter 3.
ECE 342 – Jose Schutt-Aine 1 ECE 342 Solid-State Devices & Circuits 18. Operational Amplifiers Jose E. Schutt-Aine Electrical & Computer Engineering University.
Module 4 Operational Amplifier
OPERATIONAL AMPLIFIERS. BASIC OP-AMP Symbol and Terminals A standard operational amplifier (op-amp) has; V out is the output voltage, V+ is the non-inverting.
Biomedical Instrumentation I
Operational Amplifiers
UNIT – III : OP-AMPS AND APPLICATIONS
Chapter 30 Operational Amplifiers. 2 Introduction Characteristics –High input impedance –Low output impedance –High open-loop gain –Two inputs –One output.
Parameters of OP-AMP M.S.P.V.L Polytechnic College, Pavoorchatram.
Amplifiers. BASIC AMPLIFIER CONCEPTS Ideally, an amplifier produces an output signal with identical waveshape as the input signal, but with a larger.
Applications of OP-AMP. Introduction Operational amplifier using IC's is inexpensive, versatile and easy to use. For this reason they are used not only.
Chapter 15 Differential Amplifiers and Operational Amplifier Design
Lecture VIII Operational Amplifiers DMT 231/3 Electronic II.
1 CHAPTER 20 OPERATIONAL AMPLIFIERS (OP-AMPS). 2 Introduction to operational amplifiers Symbol and Terminals.
PRESENTATION ON:  Voltage Amplifier Presentation made by: GOSAI VIVEK ( )
OPERATIONAL AMPLIFIERS + - Presented by D.Satishkumar Asst. Professor, Electrical & Electronics Engineering
1 Operational Amplifiers 1. 2 Outlines Ideal & Non-ideal OP Amplifier Inverting Configuration Non-inverting Configuration Difference Amplifiers Effect.
Differential voltage-gain device that amplifies the difference between the voltages existing at its two input terminal. An instrumentation (or instrumentational)
Operational Amplifiers 1. Copyright  2004 by Oxford University Press, Inc. Microelectronic Circuits - Fifth Edition Sedra/Smith2 Figure 2.1 Circuit symbol.
CHAPTER 20 OPERATIONAL AMPLIFIERS (OP-AMPS). Introduction to operational amplifiers Symbol and Terminals.
Ref:080114HKNOperational Amplifier1 Op-Amp Properties (1)Infinite Open Loop gain -The gain without feedback -Equal to differential gain -Zero common-mode.
EE101-Lecture 9 Operational Amplifier EE101 Fall 2012 Lect 9- Kang1 Non-inverting amplifier & Inverting amplifier.
Guided by - Prof. N A Gajjar Prepared by : Hemaxi Halpati : Priyank Hirani : Manish Jatiya : Rakesh.
Shantilal Shah Government Engineering College Bhavnagar Electrical Engg. Department.
Module 2 Operational Amplifier Basics
ARUN MUCHHALA ENGINEERING COLLEGE- DHARI [ ] ANALOG ELECTRONICS Prajapati Omprakash rd ELECTRICAL DEPARTMENT ANALOG ELECTRONICS.
Operational Amplifiers Chapter 10 Boylestad Electronic Devices and Circuit Theory.
Operational Amplifier
PUSAT PENGAJIAN KEJURUTERAAN KOMPUTER & PERHUBUNGAN
Operational Amplifier
Branch:- Electrical (09)
Analogue Electronics Circuit II EKT 214/4
Analogue Electronic 2 EMT 212
Electronic Devices Ninth Edition Floyd Chapter 12.
Medical electronics II
Differential Op - Amplifier TIM. 1 Introduction 2 Differential Amplifier: 2.1 Input Resistances: 2.2 Differential Gain: 2.3 Common Mode Input: 2.4 Common.
Department of CNET Electronic Circuit II
Medical electronics II
Department of CNET Electronic Circuit II
Presentation transcript:

Common Mode Rejection Ratio www.ustudy.in

Introduction The common-mode rejection ratio (CMRR) of a differential amplifier (or other device) measures the tendency of the device to reject input signals common to both input leads. A high CMRR is important in applications where the signal of interest is represented by a small voltage fluctuation superimposed on a (possibly large) voltage offset, or when relevant information is contained in the voltage difference between two signals. www.ustudy.in

Cont.., Ideally, a differential amplifier takes the voltages V + and V − on its two inputs and produces an output voltage Vo = Ad(V + − V − ), where Ad is the differential gain. However, the output of a real differential amplifier is better described as where Acm is the common-mode gain, which is typically much smaller than the differential gain. www.ustudy.in

Definition The CMRR is defined as the ratio of the powers of the differential gain over the common-mode gain, measured in positive decibels (thus using the 20 log rule): As differential gain should exceed common-mode gain, this will be a positive number, and the higher the better. www.ustudy.in

The CMRR is a very important specification, as it indicates how much of the common-mode signal will appear in your measurement. The value of the CMRR often depends on signal frequency as well, and must be specified as a function thereof. It is often important in reducing noise on transmission lines. For example, when measuring the resistance of a thermocouple in a noisy environment, the noise from the environment appears as an offset on both input leads, making it a common-mode voltage signal. The CMRR of the measurement instrument determines the attenuation applied to the offset or noise. www.ustudy.in

Measuring Common Mode Rejection Ratio Common-mode rejection ratio can be measured in several ways. The method shown in Figure below uses four precision resistors to configure the op amp as a differential amplifier, a signal is applied to both inputs, and the change in output is measured—an amplifier with infinite CMRR would have no change in output. The disadvantage inherent in this circuit is that the ratio match of the resistors is as important as the CMRR of the op amp. www.ustudy.in

A mismatch of 0.1% between resistor pairs will result in a CMR of only 66 dB—no matter how good the op amp! Since most op amps have a low frequency CMR of between 80 dB and 120 dB, it is clear that this circuit is only marginally useful for measuring CMRR (although it does an excellent job in measuring the matching of the resistors!). www.ustudy.in

Simple Common-Mode Rejection Ratio (CMRR) Test Circuit www.ustudy.in

The slightly more complex circuit shown in Figure below measures CMRR without requiring accurately matched resistors. In this circuit, the common-mode voltage is changed by switching the power supply voltages. (This is easy to implement in a test facility, and the same circuit with different supply voltage connections can be used to measure power supply rejection ratio). www.ustudy.in

CMRR Test Circuit Does Not Require Precision Resistors www.ustudy.in

The power supply values shown in the circuit are for a ±15 V DUT op amp, with a common-mode voltage range of ±10 V. Other supplies and common-mode ranges can also be accommodated by changing voltages, as appropriate. The integrating amplifier A1 should have high gain, low VOS and low IB, such as an OP97 family device. www.ustudy.in

Given: A 741 op amp with CMRR = 90 dB and a noise gain, AN = 1 k Find: The common mode gain, Acm Example 1: Solution: Acm = AN = 1000 log-1 (CMRR / 20) log-1 (90 / 20) = 0.0316 It is very desirable for the common-mode gain to be small. www.ustudy.in

Example 2: Solution: From the defining equation for CMRR: 5000 Common-Mode Rejection Ratio (CMRR) Example 2: A certain diff-amp has a differential voltage gain of 500 and a common-mode gain of 0.1. What is the CMRR? Solution: From the defining equation for CMRR: 5000 Expressed in decibels, it is 74 dB www.ustudy.in

Common-Mode Rejection Ratio (CMRR) Example 3: A certain diff-amp has Ad = 100 and a CMRR of 90 dB. Describe the output if the input is a 50 mV differential signal and a common mode noise of 1.0 V is present. Solution: The differential signal is amplified by 100. Therefore, the signal output is Vout = Av(d) x Vin = 100 x 50 mV = 5.0 V The common-mode gain can be found by The noise is amplified by 0.0032. Therefore, Vnoise = Acm x Vin = 0.0032 x 1.0 V = 3.2 mV www.ustudy.in

Quiz 1. When two identical in-phase signals are applied to the inputs of a differential amplifier, they are said to be a. feedback signals. b. noninverting signals. c. differential-mode signals. d. common-mode signals. www.ustudy.in

Quiz 2. Assume a differential amplifier has an input signal applied to the base of Q1 as shown. An inverted replica of this signal will appear at the emitter terminals. collector of Q1 collector of Q2 all of the above. RC1 RC2 Q1 Q2 RE -VEE www.ustudy.in

Quiz 3. A differential amplifier will tend to reject noise that is in differential-mode. noise that is in common-mode. only high frequency noise. all noise. www.ustudy.in

Quiz 4. The average of two input currents required to bias the first stage of an op-amp is called the a. input offset current. b. open-loop input current. c. feedback current. d. input bias current. www.ustudy.in

Quiz 5. The slew rate illustrated is a. 0.5 V/ms b. 1.0 V/ms c. 2.0 V/ms d. 2.4 V/ms Vout (V) 12 10 -10 -12 10 ms www.ustudy.in

Quiz 6. For the circuit shown, Vf is approximately equal to a. Vin b. Vout c. ground. d. none of the above. - + Feedback network Vf Vin Rf Ri Vout www.ustudy.in

Quiz 7. For the inverting amplifier shown, the input resistance is closest to a. zero b. 10 kW c. 2 MW d. 8 GW Rf 150 kW Ri Vin - Vout 10 kW + www.ustudy.in

Quiz 8. For the inverting amplifier shown, the output resistance is closest to a. zero b. 10 kW c. 150 kW d. 8 GW Rf 150 kW Ri Vin - Vout 10 kW + www.ustudy.in

Quiz 9. The gain of the inverting amplifier shown is a. -1 b. -10 c. -15 d. -16 Rf 150 kW Ri Vin - Vout 10 kW + www.ustudy.in

Quiz 10. A voltage follower has a. current gain. b. voltage gain. c. both of the above. d. none of the above. www.ustudy.in

Quiz Answers: 1. d 2. b 3. b 6. a 7. b 4. d 8. a 5. c 9. c 10. a www.ustudy.in