Cody Kieler Kevin Keating 02/15/2013. Lab #1 - Resistor Lab Cody Kieler Kevin Keating Date: 02/15/2013 Tools: Multimeter Parts: 25- 100 ohm resistors.

Slides:

Advertisements

Similar presentations

Series and Parallel Circuits

Advertisements

6V Voltage (V) Current (A) Your teacher will show you how to build this circuit. Copy the.

Internal Resistance. Batteries and generators add some resistance to a circuit. This resistance is called internal resistance. The actual voltage between.

Voltage Drops Around Closed Loops 470  220  5V   220  living with the lab.

Simple Electronics: Ring Oscillator

If the 2 cm long resistor is 3 ohms, what is the resistance of the 1 cm long resistor (with half the radius)? (Both are of the same material.) A] 1 ohm.

5/19/03 Minute Paper If a piezo-electric motor can expand and contract with voltage, can it also produce a voltage when it is expanded or contracted? Is.

Thursday November 29, 2007SNC1D | Miss. Manaktola 1 Simple Circuits Quiz SNC1D: Thursday November 29, 2007.

Blinking LED Lab David Luong Herrick Chang. Recall Capacitor Flash in disposable camera.

Resistor Code How to read the value of a resistor.

Calibration is a comparison between measurements of known magnitude with one device and another measurement made in as similar a way as possible with.

+ Using Ohm’s Law to Build a Voltage Divider 1. + Learning Objectives Understand and demonstrate the engineering design process Use Ohm's Law as a tool.

Ohm’s Law V = IR.

Electricity Define Electricity: Electrons: Short Circuit: Current: Battery: Voltage:

Introduction to Circuits – Practical Resources.  Reading resistors ▪

Section 2: Series and Parallel Circuits. Series Circuits Picture of Series Circuit:Properties: 1)Current: 2) Voltage: 3) Equivalent Resistance:

Measuring the Current and Voltage of a 820 Ω Resistor Setting for Multimeter = 200 mA DC Measure Voltage in 2 V increments up to 20 V.

Forging new generations of engineers

DIGITAL MULTIMETER A Must Have For Dealing With Electronics.

Introduction to Robotics for Teachers Lab Instructors: Quentin Stoll (a.k.a - Q) Matthew Miller.

The Math for Ohms Law along in DC Circuits

+ Using Ohm’s Law to Build a Voltage Divider 1. + Learning Objectives Understand and demonstrate the engineering design process Use Ohm's Law as a tool.

Solving for current, resistance and voltage in circuits.

Tutorial 1 Question 1 If a given resistor in the lab has the following colours bands from left to right, what is its value? ( Yellow, Purple, Red, Gold)

Regents Physics Chapters 17/18 Circuits  Series Circuits.

Digital Multimeter (DMM) Used to measure the following: Voltage – DC and AC Current – DC and AC Resistance Capacitance Temperature – w/ extra probe Also.

Bellwork (2/26) What do voltage sources do in a circuit? They do work on charges that is transferred into electric potential energy. Aside: High voltages.

Internal Resistance.

Bellwork (2/26) What do voltage sources do in a circuit? They do work on charges that is transferred into electric potential energy. Aside: High voltages.

How to Calculate Total Circuit Current in a Series Circuit ?

Series and Parallel.  a single resistance that can replace all the resistances in an electrical circuit while maintaining the same current when connected.

Lab 2 Density of a Solid and Liquid Objective - Measure the density of aluminum and water.

Physics A First Course Electricity Chapter 13.

I Example: A 12 V battery with 2  internal resistance is connected to a 4  resistor. Calculate (a) the rate at which chemical energy is converted to.

Lab, Project Wednesday, February 24, Unit 9: Electricity Friday, 2/26 Upcoming dates  Friday, 2/26 – Project due at end of the period (test grade)

Ohm’s Law Ohm’s Law Gateway To Technology

U3e-L4 1.Get out last night’s homework. 2.Calculate the total resistance of a circuit with 3 resistors (5, 20, and 30 ohms) in series. Sketch a schematic.

Test Friday, March 4, Draw a series and parallel circuit. Each circuit has a 200 V battery and three resistors (5 ohms, 10 ohms, 20 ohms). 2.

HOW FAST IS A NANOSECOND?. ONE-BILLIONTH OF A SECOND!!!

Intro to Electricity Electricity Definition: Circuit Definition: Three things for a circuit to work:

 A multimeter is tool that measures electrical currents. It is a combination of many different measurements in one tool.

Using a Mulitmeter A digital multimeter is a test tool used to measure two or more electrical values—principally voltage (volts), current (amps) and resistance.

Ying Yi PhD Physics Lab 2 1 PHYS Lab HCC 2014 Spring.

The Series Circuit Summary 1. The sum of the _____________or voltage equals the potential rise of the source. 2. The current is ______________ everywhere.

Set up your circuit board 2 batteries, bulb, switch, and variable resister.

Electricity Definitions

Experiment #1 Measurement of Resistance

Series and Parallel Circuits

How to read the value of a resistor

Norton’s Theorem. By: Engr.Irshad Raheem Memon

Thevenin’s Theorem By: Engr.Irshad Raheem Memon

September 7, 2017 Resistance Length of Wire Affects Resistance

Circuit Introduction Section 1:

Forging new generations of engineers

Digital Multimeter (DMM)

a) For the trace, determine

Ohm’s Law The relationship between voltage, current and resistance is known as Ohm’s Law: V = IR Voltage (V) = Current (I) x Resistance (R) Volts.

FIGURE 6-1 The amount of current flowing into junction point A equals the total amount of current flowing out of the junction.

(a) the equivalent resistance, (b) V0,

FIGURE 6-1 The amount of current flowing into junction point A equals the total amount of current flowing out of the junction.

Unit 3 Review (Calculator)

Ohm’s Law – The relationship between Current, Voltage and Resistance.

Resistance in Series and Parallel

Series Circuits Makeup Lab

Bell work: You want a circuit with 3 bulbs

Ohm’s Law Practice Problem Set Name: ___________________________

Calculate 9 x 81 = x 3 3 x 3 x 3 x 3 3 x 3 x 3 x 3 x 3 x 3 x =

Thing / Person:____________________ Dates:_________________

Record your QUESTIONS as your read.

Chapters 18 & 19 What is the definition of electric potential?

Presentation transcript:

Cody Kieler Kevin Keating 02/15/2013

Lab #1 - Resistor Lab Cody Kieler Kevin Keating Date: 02/15/2013 Tools: Multimeter Parts: ohm resistors Procedure: Use the multimeter to measure the resistance in each resistor. Record the data and compare the results with the anticipated results. Calculate the tolerance for each resistor. Include the findings from the other groups for a broader analysis.

resistorreading