New Hardware – Peripheral - 1 KX-NT136 (IP-PT) Connection via IP User Interface is same as TD7636. Almost of KX-TD7636 Functions is in it. PC-Phone/Console doesn’t work with. PC Maintenance Console doesn’t connect. (USB port is not supported) Navigation Key Dual color 24 Flexible Keys Visible Large Ring/Msg Lamp 6 Lines 24 digits LCD /w backlit RJ45 RJ11 TDA LAN PC Benefit Remote Office, Easy moving in network, Cost saving

System Connection Diagram - 1 IP Connection PC IP-PT External Sensor/ External Relay Device Remote PC PC Trunk (Telephone Company Lines) Analogue / BRI / PRI / T1 / E1 Private IP Network Router Server PC PC PC Batteries SLT DPT APT DSS DPT DSS PC or Printer T7633/36 PC USB T7600 DPT DXDP Doorphone & Door Opener SLT CS Wireless Phone PS BGM/MOH Pager/ Speaker Amplifier FAX ISDN Telephone Voice　Processing System Peripheral Connection Legacy Connection

System Connection Diagram – 2 PC T7600 DPT DPT DSS PT-IF CS PS Voice Processing System SLT FAX APT Wireless Phone Same capability of DLC CS LAN Server PC Doorphone & Door Opener Pager/Speaker Amplifier Radio DLC16 (TDA0172) DLC8 (TDA0171) DHLC8 (TDA0170) MSLC16 (TDA0175) SLC16 (TDA0174) SLC8 (TDA0173) CSIF4 (TDA0143) CSIF8 (TDA0144) CTI-LINK (TDA0410) OPB3 (TDA0190) DPH4 (TDA0161) DPH2 (TDA0162) ECHO16 (TDA0166) MSG4 (TDA0191) LCOT4 (TDA0183) LCOT16 (TDA0181) LCOT8 (TDA0180) CID/PAY8 (TDA0189) CID8 (TDA0193) DID8 (TDA0182) E&M8 (TDA0184) BRI4 (TDA0284) BRI8 (TDA0288) PRI30 (TDA0290CE/CJ) PRI23 (TDA0290) T1 (TDA0187) E1 (TDA0188) IP-GW4 (TDA0480) IP-GW4E (TDA0484) MPR MEC (TDA0105) RMT (TDA0196) PSU-S/M/L TDA0108/0104/0103 Router Batteries SMDR PC PSTN Analogue E&M ISDN BRI ISDN PRI T1 E1 Private IP Network EXT-CID (TDA0168) IP-EXT16 (TDA0470) LAN IP-PT PC IP-GW16 (TDA0490) EIO4 (TDA0164) External Sensor / External Relay Device

Function – Highlight Function - Highlight

16 ports IP-GW Card - 1 - model number is KX-TDA0490. - 16ch IPGW Card occupies a Single slot in TDA100/200 Physical I/F single Ethernet 10/100BaseT (auto sense) LED’s - Status, Link, Data, Online, Alarm & Busy - G729a/G723.1/G711 - T.38 (FAX) mode is not supported (FAX = G711) - Configuration using Web browser (English) - 100% call compatibility with TDA0484/3480 - Interoperability with TDA0480 Incoming call, Outgoing call and CLIP only. - Interoperability with another manufacturers : Not guaranteed. - Power factor is 0.

16 ports IP-GW Card - 2 Compatibility The compatibility of the IPGW4 (TDA0480), IPGW4E (TDA484), IPGW16 (TDA0490) and the TDA30 IPGW4 (TDA3480) is described in the table below: Compatibility TDA0480 TDA0484/TDA3480 TDA0490 Signalling H.323 V2 QSIG service Proprietary H.323 V4 Annex M1 Max networked IPGW’s 511 Voice Codec G.723/G.729a G.711/G.723.1/G.729a FAX Protocol T.38 G.711 Echo canceller 16ms 48/128ms AGC Yes No DTMF Tone Detection SNMP Event Notice by email DHCP Yes (Client) NAT

16 ports IP-GW Card - 3 Interoperability The interoperability of the IPGW4 (TDA0480), IPGW4E (TDA484), IPGW16 (TDA0490) and the TDA30 IPGW4 (TDA3480) is described in the table below: Function TDA0480 connected to TDA0384/TDA0484/TDA0490 Connected to TDA0384/TDA0484/TDA0490 Connected to TDA0480 CLIP OK OK OK COLP OK OK No COLR OK OK No CNIP OK OK No CNIR OK OK No CONP OK OK No CONR OK OK No CT(Avoid Tromboneing) OK OK No CF(Avoid Tromboneing) OK OK No CCBS OK OK No Making/Receiving Call OK OK OK Fax Connection OK OK No

IP PT Extension (Benefit 1) What is benefit of IP Extension Two type wirings require two types of construction, maintenance and their time. One type wiring save them. Router LAN Router LAN IP-PT Unified wiring give low cost construction and maintenance.

IP PT Extension (Benefit 2) What is benefit of IP Extension Normal Extension IP Extension Slot:301 Port:02 Slot:201 Port:01 LAN Setting change will be required. Just MOVE EXT.201 EXT.201? EXT.201 EXT.201 MOVE IP-PT IP-PT Setting change is not necessary Easy & Quick move enable

IP PT Extension (Benefit 3) What is benefit of IP Extension Router IP Network Private Leased Line IP-PT PBX LAN Head Office Branch Office PBX is not necessary for Branch Office. All setting can be controlled by Head Office.

IP PT –1 (Sample Configuration) Sample of configuration Feature of IP PT(KX-NT136) is basically same as KX-T7636. Except: OHCA, USB connection, 12CO Key connection, Digital XDP, and Walking Extension Head Office Branch Office Private IP Network IP-PT IP-EXT16 LAN IP-PT Secondary Ethernet Port IP-PT 大石 3. IP PT Extension benefitと制限事項をきちんと記述する (DHCP Server) PC Primary Ethernet Port

IP PT –2 (Requirements) Requirements - IP-EXT16 card is required. -DHCP (Dynamic Host Configuration Protocol) Server is not supported by IP-EXT16 card. You need to assign IP address of IP-EXT16 card by manual. - Cable: 100 BASE-TX Category 5 or higher - Power source: Power-over-Ethernet (PoE) or KX-A237 AC Adaptor is necessary Note: Following features are not supported. OHCA, USB connection, 12CO Key connection, Digital XDP, and Walking Extension IP-PT cannot be used for initial set-up of PBX system.

IP PT –3 (Programming IP-EXT. Card) Programming Instruction Step 1 Step 2 Step 3 Assign IP Address for IP-EXT. card by manual Assign IP Address for IP-PT Register IP-PT IP Address & Subnet mask (GW Address for IP-PT) * If necessary (See page IP-PT7) 1. Configuration 1. Slot 2. System 14. IP Extension Setting IP-EXT16 Property

IP PT –4 (Programming IP-PT) Programming Instruction Step 1 Step 2 Step 3 Assign IP Address for IP-EXT. card Assign IP Address for IP-PT Register IP-PT At start up 2. Press “Enter” key at 1st installation or 1. Power on IP-PT 3. Select “Network” 2. Press “Set-up” soft key from 2nd time LCD status 2. At 1st installation Menu Please first setup ! OK [ENTER] 3. Menu select 1. Start up Menu Network PBX VLAN Maintenance STORE EXIT CONT ENTER 操作がわかりやすい絵とか写真とか考えて欲しい9/9 IPL Start… Now Loading 2. From 2nd time Searching… Setup

IP PT –5 (Programming IP-PT) Programming Instruction Step 1 Step 2 Step 3 Assign IP Address for IP-EXT. card Assign IP Address for IP-PT Register IP-PT With DHCP Server (Automatic Assignment: IP Address for Subnet mask, IP-PT Default GW) 6. Assign IP Address for IP-EXT16 card 4. DHCP: Enable 5. Select “PBX” 7. Store LCD status 4. 5. 6. DHCP Enable IP Address 0. 0. 0. 0 Subnet Mask NEXT Disable EXIT ENTER 矢印を太くしたほうがいい？ LCD表示と操作の関連がぱっと見てわかるようにならないか? Menu Network PBX VLAN Maintenance STORE EXIT CONT ENTER PBX IP Address ? 192.168. 0.100 EXIT CLER ENTER

IP PT –6 (Programming IP-PT) Programming Instruction Step 1 Step 2 Step 3 Assign IP Address for IP-EXT. card Assign IP Address for IP-PT Register IP-PT Without DHCP Server 4. DHCP: Disable 5. Select “IP-Address” 6. Assign IP Address for IP-PT 8. Assign IP Address for Subnet mask 7. Select “Subnet mask” * 9. Select “Default GW” *10. Assign IP Address for Default GW 12. Assign IP Address for IP-EXT16 card 11. Select “PBX” 13. Store LCD status 4. – 8. 11. 12. DHCP Enable IP Address 192.168.0.101 Subnet Mask 255.255.255. 0 NEXT Disable EXIT ENTER 操作と画面の関連がぱっとわかるようにならないか？ Menu Network PBX VLAN Maintenance STORE EXIT CONT ENTER PBX IP Address ? 192.168. 0.100 EXIT CLER ENTER

IP PT –7 (Programming IP-PT) Programming Instruction Step 1 Step 2 Step 3 Assign IP Address for IP-EXT. card Assign IP Address for IP-PT Register IP-PT Without DHCP Server Head Office Branch Office Router Router Private IP Network Gateway: 192.169.0.1 Gateway:10.75.0.1 IP-EXT16 IP-PT IP-PTからする設定でいやらしいGATEWAYの設定があったはずby Mr.Take LAN DHCP Enable Default Gateway 192.168. 0. 1 PREV Disable EXIT ENTER IP-PT PC

IP PT –8 (Register IP-PT to PBX) Programming Instruction Step 1 Step 2 Step 3 Assign IP Address for IP-EXT. card Assign IP Address for IP-PT Register IP-PT Select: ON Registration Registration:Start UNREGISTERED TO SERVER OK[ENTER] LCD of IP-PT is changed to normal アブノーマルな状態(登録前の状態)のLCD表示も追加すること 30 SEP. 11:09AM FRI PROG INFO RING MENU 1. Configuration 15. IP-Extension Port Confirm: OK

IP PT –9 Virtual LAN VLAN(L2 Switch) Necessary Information VLAN Name : Sales ID : 1 Port on VLAN: 1-4 Tagged VLAN: Null PHY. Port 1 2 3 4 5 6 VLAN No. 1 1 1 1 2 2 VLAN(L2 Switch) Necessary Information Local Office Remote Office IP-PT EXT.101 IP-PT EXT.102 IP-PT EXT.103 IP-PT EXT.104 IP-PT IP Address 192.168.0.101 192.168.0.102 10.75.0.103 10.75.0.104 Subnet Mask Address 255.255.255.0 Default Gateway Address 192.168.0.1 10.75.0.1 Card IP Address 192.168.0.100 10.75.0.100 VLAN ID 1 VLAN ID is necessary for IP-PT when you connect PC to IP-PT

IP PT –10 Virtual LAN Branch Office Head Office Private IP Network Router L2 switch configuration VLAN Name : Sales ID : 1 Port on VLAN: 1-4 Tagged VLAN: Null PHY. Port 1 2 3 4 5 6 VLAN No. 1 1 1 1 2 2 L2 Switch Gateway:10.75.0.1 Gateway: 192.169.0.1 IP Network Private Branch Office Head Office VLAN ID = 1 VLAN ID = 1 IP-EXT16 LAN VLAN ID = 1 VLAN ID = 1 IP-PT IP-PT VLAN ID = 1 LCD status VLAN ID = 1 VLAN ID って何?設計者に竹さんが確認。思うではなく事実を確認。 Menu Network PBX VLAN Maintenance STORE EXIT CONT ENTER VLAN Enable Primary port Secondary port (TO PC) Disable EXIT ENTER Primary port VLAN ID VLAN Priority 1 7