ConcepTest 19.1a Series Resistors I

Slides:



Advertisements
Similar presentations
ConcepTest 1 Series Resistors I
Advertisements

© 2007 Pearson Prentice Hall This work is protected by United States copyright laws and is provided solely for the use of instructors in teaching their.
Chapter 17 Electric current
Direct Current Circuits
Ohm’s Law Objective: TSW understand the concepts of Voltage, Current, and Resistance by developing and applying Ohm’s Law.
ConcepTest 19.1aSeries Resistors I 9 V Assume that the voltage of the battery is 9 V and that the three resistors are identical. What is the potential.
Physics for Scientists and Engineers, 6e
Direct-Current Circuits
Kirchhoff’s Laws a b e R C I e R I r V.
© 2007 Pearson Prentice Hall This work is protected by United States copyright laws and is provided solely for the use of instructors in teaching their.
Chapter 26 DC Circuits Chapter 26 Opener. These MP3 players contain circuits that are dc, at least in part. (The audio signal is ac.) The circuit diagram.
Electricity Review 10 MYP Science.
Series and Parallel Circuits
Direct Current Circuits
Resistivity and Resistance
Q26.1 Which of the two arrangements shown has the smaller equivalent resistance between points a and b? A. the series arrangement B. the parallel arrangement.
© 2012 Pearson Education, Inc. Which of the two arrangements shown has the smaller equivalent resistance between points a and b? Q26.1 A. the series arrangement.
Concept Questions with Answers 8.02 W10D2
Copyright © 2009 Pearson Education, Inc. Chapter 26 DC Circuits.
Today 3/27  Circuits  Current  Potential (same as always)  HW:3/27 “Circuits 2” Due Monday 3/31.
ConcepTest 21.1 Connect the Battery
Capacitors and/or TV (not Emf). 1. An empty capacitor does not resist the flow of current, and thus acts like a wire. 2. A capacitor that is full of charge.
Light bulb When switch is closed, bulbs are … Brighter The same Dimmer than the bulb above (?)
2. the intensity of light bulb A increases.
Fundamentals of Circuits: Direct Current (DC)
Electric circuit power, circuit elements and series-parallel connections.
Chapter 23 Circuits Topics: Sample question:
7/2/20151 T-Norah Ali Al-moneef king saud university.
ConcepTest 25.1 Capacitors
1) Connect the Battery Which is the correct way to light the lightbulb with the battery? 4) all are correct 5) none are correct 1) 2) 3)
Copyright © 2009 Pearson Education, Inc. Chapter 26 DC Circuits.
Copyright © 2009 Pearson Education, Inc. Chapter 25 Electric Currents and Resistance.
Series and Parallel Circuits
ConcepTest 4.1aSeries Resistors I 9 V Assume that the voltage of the battery is 9 V and that the three resistors are identical. What is the potential difference.
ConcepTest 17.1a Electric Potential Energy I
In conclusion, there are two requirements which must be met in order to establish an electric circuit. The requirements are: 1.There must.
Lecture 13 Direct Current Circuits
Copyright © 2009 Pearson Education, Inc. Chapter 26 DC Circuits.
ConcepTest 16.1aElectric Charge I ConcepTest 16.1a Electric Charge I 1) one is positive, the other is negative 2) both are positive 3) both are negative.
Series and Parallel Circuits Making Electricity Work for Us.
ConcepTest 18.1 Connect the Battery
ConcepTest 16.1aElectric Charge I ConcepTest 16.1a Electric Charge I a)one is positive, the other is negative b)both are positive c)both are negative d)both.
Physics 2102 Circuits Circuits Physics 2102 Gabriela González b a.
Copyright © 2009 Pearson Education, Inc. Chapter 25 Electric Currents and Resistance.
© 2008 Pearson Education, Inc. This work is protected by United States copyright laws and is provided solely for the use of instructors in teaching their.
1. ConcepTest 19.1aSeries Resistors I 9 V Assume that the voltage of the battery is 9 V and that the three resistors are identical. What is the potential.
11.6 Kirchhoff’s Laws In 1845, German physicist Gustov Kirchhoff developed two important laws when investigating circuits. These laws describe the behavior.
Three identical bulbs Three identical light bulbs are connected in the circuit shown. When the power is turned on, and with the switch beside bulb C left.
Review Exam 4. Chapter 18 Electric Currents Resistance and Resistors The ratio of voltage to current is called the resistance: (18-2a) (18-2b)
Which of the circuits shown above are wired in parallel? 1) A only 2) B only 3) C only 4) B and C 5) all of them.
© 2005 Pearson Prentice Hall This work is protected by United States copyright laws and is provided solely for the use of instructors in teaching their.
Chapter 27 Lecture 23: Circuits: I. Direct Current When the current in a circuit has a constant direction, the current is called direct current Most of.
What is the equivalent resistance of this circuit? What is the current running through the first resistor? What is the potential difference drop across.
Series and Parallel Circuits
© 2005 Pearson Prentice Hall This work is protected by United States copyright laws and is provided solely for the use of instructors in teaching their.
Phys102 Lecture 10 & 11 DC Circuits Key Points EMF and Terminal Voltage Resistors in Series and in Parallel Circuits Containing Resistor and Capacitor.
DC Circuits Series and parallel rules for resistors Kirchhoff’s circuit rules.
Chapter 27 Circuits (Basic) Electric Circuits Series Connections: Total Resistance = Sum of individual Resistances. Current the same through every load.
ConcepTest 19.1aSeries Resistors I 9 V Assume that the voltage of the battery is 9 V and that the three resistors are identical. What is the potential.
19 Current, Resistance, and Directed-Current Circuits Lectures by James L. Pazun Copyright © 2012 Pearson Education, Inc. publishing as Addison-Wesley.
1) Connect the Battery Which is the correct way to light the lightbulb with the battery? 4) all are correct 5) none are correct 1) 2) 3)
Physics: Principles with Applications, 6th edition
1) Connect the Battery Which is the correct way to light the lightbulb with the battery? 4) all are correct 5) none are correct 1) 2) 3)
SPH4UW Kirchhoff’s Laws Lecture timing is fine. No need to rush 1.
Circuits Rs r Ig Is I r >> Rs A + - Chapter 27 R V r e I + -
ConcepTest 4.1a Series Resistors I
Bell Ringer: Define to the best of your ability the definition of:
Resistance of a light bulb
ConcepTest 27.1 Junction Rule
Circuits Circuit Intro
Presentation transcript:

ConcepTest 19.1a Series Resistors I 1) 12 V 2) zero 3) 3 V 4) 4 V 5) you need to know the actual value of R Assume that the voltage of the battery is 9 V and that the three resistors are identical. What is the potential difference across each resistor? 9 V

ConcepTest 19.1a Series Resistors I 1) 12 V 2) zero 3) 3 V 4) 4 V 5) you need to know the actual value of R Assume that the voltage of the battery is 9 V and that the three resistors are identical. What is the potential difference across each resistor? Since the resistors are all equal, the voltage will drop evenly across the 3 resistors, with 1/3 of 9 V across each one. So we get a 3 V drop across each. 9 V Follow-up: What would be the potential difference if R= 1 W, 2 W, 3 W

ConcepTest 19.1b Series Resistors II 1) 12 V 2) zero 3) 6 V 4) 8 V 5) 4 V In the circuit below, what is the voltage across R1? 12 V R1= 4 W R2= 2 W

ConcepTest 19.1b Series Resistors II 1) 12 V 2) zero 3) 6 V 4) 8 V 5) 4 V In the circuit below, what is the voltage across R1? The voltage drop across R1 has to be twice as big as the drop across R2. This means that V1 = 8 V and V2 = 4 V. Or else you could find the current I = V/R = (12 V)/(6 W) = 2 A, then use Ohm’s Law to get voltages. 12 V R1= 4 W R2= 2 W Follow-up: What happens if the voltage is doubled?

ConcepTest 19.2a Parallel Resistors I 2) zero 3) 5 A 4) 2 A 5) 7 A In the circuit below, what is the current through R1? 10 V R1= 5 W R2= 2 W

ConcepTest 19.2a Parallel Resistors I 2) zero 3) 5 A 4) 2 A 5) 7 A In the circuit below, what is the current through R1? 10 V R1= 5 W R2= 2 W The voltage is the same (10 V) across each resistor because they are in parallel. Thus, we can use Ohm’s Law, V1 = I1 R1 to find the current I1 = 2 A. Follow-up: What is the total current through the battery?

ConcepTest 19.2b Parallel Resistors II 1) increases 2) remains the same 3) decreases 4) drops to zero Points P and Q are connected to a battery of fixed voltage. As more resistors R are added to the parallel circuit, what happens to the total current in the circuit?

ConcepTest 19.2b Parallel Resistors II 1) increases 2) remains the same 3) decreases 4) drops to zero Points P and Q are connected to a battery of fixed voltage. As more resistors R are added to the parallel circuit, what happens to the total current in the circuit? As we add parallel resistors, the overall resistance of the circuit drops. Since V = IR, and V is held constant by the battery, when resistance decreases, the current must increase. Follow-up: What happens to the current through each resistor?

ConcepTest 19.3a Short Circuit 1) all the current continues to flow through the bulb 2) half the current flows through the wire, the other half continues through the bulb 3) all the current flows through the wire 4) none of the above Current flows through a lightbulb. If a wire is now connected across the bulb, what happens?

ConcepTest 19.3a Short Circuit 1) all the current continues to flow through the bulb 2) half the current flows through the wire, the other half continues through the bulb 3) all the current flows through the wire 4) none of the above Current flows through a lightbulb. If a wire is now connected across the bulb, what happens? The current divides based on the ratio of the resistances. If one of the resistances is zero, then ALL of the current will flow through that path. Follow-up: Doesn’t the wire have SOME resistance?

ConcepTest 19.3b Short Circuit II 1) glow brighter than before 2) glow just the same as before 3) glow dimmer than before 4) go out completely 5) explode Two lightbulbs A and B are connected in series to a constant voltage source. When a wire is connected across B, bulb A will:

ConcepTest 19.3b Short Circuit II 1) glow brighter than before 2) glow just the same as before 3) glow dimmer than before 4) go out completely 5) explode Two lightbulbs A and B are connected in series to a constant voltage source. When a wire is connected across B, bulb A will: Since bulb B is bypassed by the wire, the total resistance of the circuit decreases. This means that the current through bulb A increases. Follow-up: What happens to bulb B?

ConcepTest 19.4a Circuits I The lightbulbs in the circuit below are identical with the same resistance R. Which circuit produces more light? (brightness  power) 1) circuit 1 2) circuit 2 3) both the same 4) it depends on R

ConcepTest 19.4a Circuits I The lightbulbs in the circuit below are identical with the same resistance R. Which circuit produces more light? (brightness  power) 1) circuit 1 2) circuit 2 3) both the same 4) it depends on R In #1, the bulbs are in parallel, lowering the total resistance of the circuit. Thus, circuit #1 will draw a higher current, which leads to more light, because P = I V.

ConcepTest 19.4b Circuits II 1) twice as much 2) the same 3) 1/2 as much 4) 1/4 as much 5) 4 times as much The three lightbulbs in the circuit all have the same resistance of 1 W . By how much is the brightness of bulb B greater or smaller than the brightness of bulb A? (brightness  power) 10 V A B C

ConcepTest 19.4b Circuits II 1) twice as much 2) the same 3) 1/2 as much 4) 1/4 as much 5) 4 times as much The three light bulbs in the circuit all have the same resistance of 1 W . By how much is the brightness of bulb B greater or smaller than the brightness of bulb A? (brightness  power) 10 V A B C We can use P = V2/R to compare the power: PA = (VA)2/RA = (10 V) 2/1 W = 100 W PB = (VB)2/RB = (5 V) 2/1 W = 25 W Follow-up: What is the total current in the circuit?

ConcepTest 19.5a More Circuits I What happens to the voltage across the resistor R1 when the switch is closed? The voltage will: 1) increase 2) decrease 3) stay the same V R1 R3 R2 S

ConcepTest 19.5a More Circuits I What happens to the voltage across the resistor R1 when the switch is closed? The voltage will: 1) increase 2) decrease 3) stay the same With the switch closed, the addition of R2 to R3 decreases the equivalent resistance, so the current from the battery increases. This will cause an increase in the voltage across R1 . V R1 R3 R2 S Follow-up: What happens to the current through R3?

ConcepTest 19.5b More Circuits II 1) increases 2) decreases 3) stays the same What happens to the voltage across the resistor R4 when the switch is closed? V R1 R3 R4 R2 S [CORRECT 5 ANSWER]

ConcepTest 19.5b More Circuits II 1) increases 2) decreases 3) stays the same What happens to the voltage across the resistor R4 when the switch is closed? V R1 R3 R4 R2 S A B C We just saw that closing the switch causes an increase in the voltage across R1 (which is VAB). The voltage of the battery is constant, so if VAB increases, then VBC must decrease! Follow-up: What happens to the current through R4?

ConcepTest 19.6 Even More Circuits 2) both R1 and R2 equally 3) R3 and R4 4) R5 5) all the same Which resistor has the greatest current going through it? Assume that all the resistors are equal. V R1 R2 R3 R5 R4

ConcepTest 19.6 Even More Circuits 2) both R1 and R2 equally 3) R3 and R4 4) R5 5) all the same Which resistor has the greatest current going through it? Assume that all the resistors are equal. The same current must flow through left and right combinations of resistors. On the LEFT, the current splits equally, so I1 = I2. On the RIGHT, more current will go through R5 than R3 + R4 since the branch containing R5 has less resistance. V R1 R2 R3 R5 R4 Follow-up: Which one has the smallest voltage drop?

ConcepTest 19.7 Junction Rule 1) 2 A 2) 3 A 3) 5 A 4) 6 A 5) 10 A What is the current in branch P? 5 A 8 A 2 A P [CORRECT 5 ANSWER]

ConcepTest 19.7 Junction Rule 1) 2 A 2) 3 A 3) 5 A 4) 6 A 5) 10 A What is the current in branch P? 5 A 8 A 2 A P junction 6 A The current entering the junction in red is 8 A, so the current leaving must also be 8 A. One exiting branch has 2 A, so the other branch (at P) must have 6 A. S

ConcepTest 19.8 Kirchhoff’s Rules 1) both bulbs go out 2) intensity of both bulbs increases 3) intensity of both bulbs decreases 4) A gets brighter and B gets dimmer 5) nothing changes The lightbulbs in the circuit are identical. When the switch is closed, what happens? [CORRECT 5 ANSWER]

ConcepTest 19.8 Kirchhoff’s Rules 1) both bulbs go out 2) intensity of both bulbs increases 3) intensity of both bulbs decreases 4) A gets brighter and B gets dimmer 5) nothing changes The lightbulbs in the circuit are identical. When the switch is closed, what happens? When the switch is open, the point between the bulbs is at 12 V. But so is the point between the batteries. If there is no potential difference, then no current will flow once the switch is closed!! Thus, nothing changes. 24 V Follow-up: What happens if the bottom battery is replaced by a 24 V battery?

ConcepTest 19.10 More Kirchhoff’s Rules 1) 2 – I1 – 2I2 = 0 2) 2 – 2I1 – 2I2 – 4I3 = 0 3) 2 – I1 – 4 – 2I2 = 0 4) I3 – 4 – 2I2 + 6 = 0 5) 2 – I1 – 3I3 – 6 = 0 Which of the equations is valid for the circuit below? 2 V 2  6 V 4 V 3  1  I1 I3 I2

ConcepTest 19.10 More Kirchhoff’s Rules 1) 2 – I1 – 2I2 = 0 2) 2 – 2I1 – 2I2 – 4I3 = 0 3) 2 – I1 – 4 – 2I2 = 0 4) I3 – 4 – 2I2 + 6 = 0 5) 2 – I1 – 3I3 – 6 = 0 Which of the equations is valid for the circuit below? Eqn. 3 is valid for the left loop: The left battery gives +2V, then there is a drop through a 1W resistor with current I1 flowing. Then we go through the middle battery (but from + to – !), which gives –4V. Finally, there is a drop through a 2W resistor with current I2. 2 V 2  6 V 4 V 3  1  I1 I3 I2

ConcepTest 19.11a Capacitors I 1) Ceq = 3/2 C 2) Ceq = 2/3 C 3) Ceq = 3 C 4) Ceq = 1/3 C 5) Ceq = 1/2 C What is the equivalent capacitance, Ceq , of the combination below? o C Ceq

ConcepTest 19.11a Capacitors I 1) Ceq = 3/2 C 2) Ceq = 2/3 C 3) Ceq = 3 C 4) Ceq = 1/3 C 5) Ceq = 1/2 C What is the equivalent capacitance, Ceq , of the combination below? o C Ceq The 2 equal capacitors in series add up as inverses, giving 1/2 C. These are parallel to the first one, which add up directly. Thus, the total equivalent capacitance is 3/2 C.

ConcepTest 19.11b Capacitors II 1) V1 = V2 2) V1 > V2 3) V1 < V2 4) all voltages are zero How does the voltage V1 across the first capacitor (C1) compare to the voltage V2 across the second capacitor (C2)? C1 = 1.0 mF C3 = 1.0 mF C2 = 1.0 mF 10 V

ConcepTest 19.11b Capacitors II 1) V1 = V2 2) V1 > V2 3) V1 < V2 4) all voltages are zero How does the voltage V1 across the first capacitor (C1) compare to the voltage V2 across the second capacitor (C2)? The voltage across C1 is 10 V. The combined capacitors C2+C3 are parallel to C1. The voltage across C2+C3 is also 10 V. Since C2 and C3 are in series, their voltages add. Thus the voltage across C2 and C3 each has to be 5 V, which is less than V1. C1 = 1.0 mF C3 = 1.0 mF C2 = 1.0 mF 10 V Follow-up: What is the current in this circuit?

ConcepTest 19.11c Capacitors III 1) Q1 = Q2 2) Q1 > Q2 3) Q1 < Q2 4) all charges are zero How does the charge Q1 on the first capacitor (C1) compare to the charge Q2 on the second capacitor (C2)? C1 = 1.0 mF C3 = 1.0 mF C2 = 1.0 mF 10 V

ConcepTest 19.11c Capacitors III 1) Q1 = Q2 2) Q1 > Q2 3) Q1 < Q2 4) all charges are zero How does the charge Q1 on the first capacitor (C1) compare to the charge Q2 on the second capacitor (C2)? We already know that the voltage across C1 is 10 V and the voltage across C2 and C3 each is 5 V. Since Q = CV and C is the same for all the capacitors, then since V1 > V2 therefore Q1 > Q2. C1 = 1.0 mF C3 = 1.0 mF C2 = 1.0 mF 10 V